Thanks for this video. I enjoy working on old 3 Speeds so it’s always good to see what other people do to get old parts working again. Keep up the good work!
Thanks very much. I'm just refurbishing my dad's 1962 Raleigh Superbe with a four-speed SA FG hub. I'm no expert, so everything's trial and error. I stripped the trigger, cleaned it, and reassembled using two 2BA brass screws and nuts rather than rivets. The bike will get very little use, so the screw shanks shouldn't wear a lot.
I was thinking of doing the same thing! Using small nuts and bolts to hold it together. But maybe not. I just think it would be easier to clean. How has your been working out?
I think when assembling the two pins it is important to put the back plate onto a hole and then to press or hammer them into their final position. However, thanks for the instruction!
Great vid and knowledge, how did you flatten out the drill bit end pls also how does the new wire fit in :) you keep posting i will keep watching Steve NZ
Thanks Stephen for watching, the drill bit sits in place snug so just make sure you get the correct thickness or sand down to make fit, the gear cable are you referring too, if so that goes in at the back of the lever 👍
Hi, Great video. I need to service my 4 sp SA shifter as I suspect the clutch and spring need replacing, it does not hold gear 1. Where can I purchase a new clutch? Can I send this into you for a service?
B for Bottom gear (super low) L for regular Low gear- N for normal(direct drive} and H for High gear(overdrive). The sturmey archer story by Tony Hadland is good. Just in case you want to know almost everything. Except 4 speed trigger work.
Patience of a saint. Well done, most enjoyable to watch.
Thanks for this video. I enjoy working on old 3 Speeds so it’s always good to see what other people do to get old parts working again. Keep up the good work!
Thank you franco 👍
brilliant ! always wondered how these worked since I was a kid lol
Thanks very much. I'm just refurbishing my dad's 1962 Raleigh Superbe with a four-speed SA FG hub. I'm no expert, so everything's trial and error. I stripped the trigger, cleaned it, and reassembled using two 2BA brass screws and nuts rather than rivets. The bike will get very little use, so the screw shanks shouldn't wear a lot.
I was thinking of doing the same thing! Using small nuts and bolts to hold it together. But maybe not. I just think it would be easier to clean. How has your been working out?
@@greg1268 I think it's fine, but I've hardly used the bike. I think the screws will last many years.
What a patient guy. Nice work.
Thank you 🙏
Great video!! So very helpful!!!! Many thanks!!!!
Your welcome
I think when assembling the two pins it is important to put the back plate onto a hole and then to press or hammer them into their final position. However, thanks for the instruction!
Thank you sir
For this shifter restore tips
I am also happy
Your welcome buddy 👍
Super to watch, thx a lot!
Your welcome 👍
Great video, I just happen to be refurbishing 2 3 speed trigger shifters that I picked up from eBay
👍👍👍
Thank you 😊 and good luck with your refurb 👍
Great vid and knowledge, how did you flatten out the drill bit end pls also how does the new wire fit in :) you keep posting i will keep watching Steve NZ
Thanks Stephen for watching, the drill bit sits in place snug so just make sure you get the correct thickness or sand down to make fit, the gear cable are you referring too, if so that goes in at the back of the lever 👍
Is it not possible to add tension to the spring by bending it slightly?
as a kid, I had one on a stingray with banana seat.
Nice effort 👍, Can I get few numbers of shifters for restoration of my 3&4 speed hubs.
Hi thanks
What’s your question please ?
@@retrobikestuff760 I want few numbers of shifters, can you give me .
Hi,
Great video. I need to service my 4 sp SA shifter as I suspect the clutch and spring need replacing, it does not hold gear 1. Where can I purchase a new clutch? Can I send this into you for a service?
Check eBay for parts although they are hard to find, I’m also after some bits 😂
Thanks also 👍
What did you clean the plate it to make it go gold coloured? It's a nice touch.
If you use a fine wire wool it will take off the silver, maybe a bit of cutting paste too 👍
Thank you 😊
Thankiu. Nice. 👍🚴
Cool video! Do you lubricate the shifter at all?
Thank you, occasional thin oil will be fine mate 👍
hello mate are the sturmey archer 4 speed hubs still available today in this year of 2021?
Is there a reason you're not greasing everything up before reassembly ??
I’m demonstrating problem solving however lite oiling will suffice 👍
Why couldn't you bend the spring to make it tighter?
You can try that, in the past the springs have snapped on me so I avoid it
BLNH on the trigger what does that stand for?
B for Bottom gear (super low) L for regular Low gear- N for normal(direct drive} and H for High gear(overdrive). The sturmey archer story by Tony Hadland is good. Just in case you want to know almost everything. Except 4 speed trigger work.
@@Apheresis ok thank you.
Try it on with cable
Itu harganya berapa
Suwiterny pak