My dealership told me It wouldn’t be smart to replace my trans fluid & filter due to Viscosity differences and recommended my original life factory fluid was suited for my car. I have a 07’ 650i (E63) and It shifts a bit clunky. Other then that the cars great 91k miles
@@BellaNoir3 well a bmw dealership is trying to persuade me to replace the transmission for $8,000.. versus fixing the problem!! I was told by a sister company their trying to get a big commission check versus $1,500-2,000 they would normally make.. the car is still sitting at the dealership for six weeks, ill pick it up next month and leave in my driveway
I have a 2012 740I and when I push the button simply to put it in park it goes to neutral with a message saying use the parking brake to ensure it doesn't roll. Consult a service center. Is there an easier fix?
Thank you for the video, you're knowledge is appreciated! Please explain how to fix my trouble code... I have 2011 750li 107k miles trans code: 400126 - solenoid 3 (parking-lock holding magnet short circuit to ground or open circuit) I have already replaced plug adapter,4 stem seals and bridge seal... Along with new pan/filter and trans oil. Stl no fix
Hi thanks a lot for the information. I have 2012 BMW740LI I just go to garage for change transmission oil change .they saying they will change but they not take any responsibility. they propose not to change. now my car run 140000km i buy this last year that time132000km drive. I asked that owner when the last time change oil he not remember. Please advice what shod i do. Thanks..
Hi I have a 2009 bmw 750i I have been getting a Transmission malfunction warning so I took the car to a indy in my area. When the car was first diagnosed it was sending a code that said the shift solenoid C was the problem so I purchased solenoids and transmission fluid, filter and all. My mechanic checked it out and said that it needed fluid. To make a long story short he tested the solenoids all of them were good so he added fresh fluid and a need transmission filter so he did that I went to pick up the car today and it was still showing transmission malfunction. Does anyone know if the transmission needs to be reset for it to work properly with the new fluid and all? Any help will be appreciated Thanks
I have a 2013 bmw 650i stuck in neutral it won’t even start up at all new engine new injectors and everything what could be the issue I need to drive my car please help 😔
My 750 won’t go into P light flickers and go back to N and when I drive the car trans erratically switches gears back and forth like it has lost its mind, anyone has same problem ? Any solutions, ideas would be helpful, thanks
My 2007 BMW 525i will make a click sound in the actual gear shift then is stuck in z1st gear and won’t shift u til I turn the car off then it’s stuck in park and I use the gear shift release to out in drive but then it’s stuck in first gear again. Then I the. The engine off and on some times it will shift and be fine until I hear this click sound again and it’s stuck in first gear.
Hi Guys have bmw 2015 3series diesel automatic transmision 8gear.Question when I driving on M+S it’s says on the dash S7 but not showing 8gear.Is this normal or it should show S8 when I driving 140-160kmph.I thinking maybe it’s not shifting into 8gear.But drives no problem no lights on dash nothing.Can someone explain me please?
CF19C1 amigo tengo ese error en la transmisión y me dice que tiene pérdida de potencia y que conduzca moderadamente, dice errores del grupo 3 durante la marcha de mi serie 5 BMW podrías ayudarme?
What does my 2015 528i twin turbo get this code 420641 while I'm driving and the auto engine button doesn't work but if i put the auto H button the problem with the gear changing to neutral and then to drive until i have to restart the car but if i have the auto H button it won't cause the problem as much but it still does it and then if i have the auto H on and turn on the sport or eco function it will go back to comfort and it won't go too fast or the turbo won't work properly. The code it gives me is 420641 and it only gives me the code whenever I that problem happens and i have to have the code reader connected to get the code but the code says that i actually pressing the Park button on while driving(moving car) why does it do that and i can't find no one that can actually fix it cause i live in a small county and the nearest bmw is 2 hrs away.
Hi Francisco, thanks for all the good educational videos on your chanel. I own a regular 2012 750LI and recenlty a transmission malfunction light came up and the car went into the safety mode you explained. I plugged in my Autel MK808 and 400341 popped up. The symtoms before the light came up was that the car will not shift properly in the lower gears and after hesitating for a few seconds it will shift normally and pick up a normal acceleration (no codes registered during those conditions) but today the code showed up. Have you had any experiences with this code? Is it a serious issue? After watching one of your videos on how to replace the trans fluid and filter I feel confident that I can do it. What would you recommend I replace while doing that ?
Good day. how can i send you a video? i want to send you a video clip of what i am experiencing on my 2011 BMW X6M gear, my gear jumps on the initial start. when the car is parked for a while, and you start it and put the gear on reverse or drive, it jumps to park((P) It jumps automatically to park, except u step on the accelerator pedal at the same time as soon as you select drive or reverse, then it will now engage in driving or reverse. But it doesn't jump while the car is already in motion, except when parked and the engine is switched off for a while.
Like your video, need help on BMW 2013 535iXdrive sedan M-sport F10 model has Fault code 420321 gear shift ration monitoring gear shift 2 not plausible What can I do? thank you Jorge
Hello. Solenoid valve 2 defective short-circuit to ground or open circuit code 400116. Start engine and put on driver and D flashing. Need only valve 2 charging?thanks
Hi I need your help ...my f30 gearbox get water...the gearbox cooler broke so coolent lick into the gearbox...I removed the gearbox clean it up...now I have this fault code 420641: Parking lock defectively engaged...please help me please
I have a BMW X5 2010 3.0 xdrive . The car goes into limp mode when going up an inclined road and when gear in changing from 4th to 5th. i notice because i put the gearbox into manuel and it always slips meaning the revs go high as if in free for a split of a second then goes into 5th gear. if its on automatic it would go into limp mode. The thing is i changed the gear oil and also the o rings and gaskets. Cannot understand if it's a solenoid or a gear . BMW cannot identify the problem telling me i need a new gearbox.... can this be the situation?
Yup me to goes into limp mode when it shifts into 4th gear if you drive it manually skip 4th to 5th and 6th can't remember to skip 4th back down but I've done it once and I've also changed all six silllinois and new fluid if I remember the megatronix which looked like it had a crack in it but I didn't really think much of it because it was just a piece of plastic that still functioned if anybody has any info that would much appreciated
Having some issues like this too ! Car stuck in park not shifting at all ! The light blinking ! Had the transmission replaced 8k miles before or less ! Any other suggestions?
@@adamtorres8303 mines goes into drive, it's when I take off it slams back into park and gears on dash blinking would that be the same thing? Thanks for the response
@@adamtorres8303 I took mines to the shop also and it was low on transmission fluid they raised it up more on the driver side when refilling and it took 2 more quarts after originally thinking it was full
My 2007 BMW 525i will make s click sound in the actual gear shift then is stuck in z1st gear and won’t shift u til I turn the car off then it’s stuck in park and I use the gear shift release to out in drive but then it’s stuck in first gear again. Then I the. The engine off and on some times it will shift and be fine until I hear this click sound again and it’s stuck in first gear.
What's up Francisco? I got this code on my 2013 740i this morning. I filled my car up Tuesday, it sat for a day and when I went to start my car this morning I got a rough idle and the transmission malfunction warning on the iDrive screen. I did not turn the car on, I gave the car a little gas so it wouldn't shut off during the rough idle and then my RPMs just settled out just below 1000RPMs. I let the car warm up, drove 25 miles to work, no problems. I will drive it home soon and I don't expect any issues. I scanned with my Autel MaxiCheck MX808 and I don't see any codes I should be reading. Do you know where I should look? Thanks in advance.
I have an automatic car is doing funny things First when selected Drive or Reverse it would just jump back on its own into Park. Now its not doing that anymore. Now when i select reverse it goes into reverse and as soon as i get close to something it was sound an alarm, but when i select Drive it goes into drive and goes forward . the alarm disappears but the reversing information is still on the dash screen even when i put in Neutral. Hope i can get some help from you or someone on this chat
That is a simple thing to fix. It’s distance based. The car displays the rear backup camera info when put into reverse, the information will not go away until you travel a far enough distance forward to make it disappear. Like 15 feet or something.
I have a 2007 528xi it moves forward but won't go in reverse and also in P. When I press the P it goes straight in N it flickers but doesn't move as if it's already in Park. The only time it starts moving in reverse for a little bit is when I reset the transmission module. What should I look into? Could it be the solenoids or something else? Thank you
I have a 2012 740i BMW replaced my bad battery and now my bmw don’t want to go into gear ⚙️ transmission malfunction sign pop on my dash…bmw told me it’ll be 10k to get a new transmission…i believe that’s bullshit cause my car didn’t have transmission problems after they placed the new battery in…so it’s just parked outside my home and still runs but won’t go into gear…I need help & information on what to do next
@@choppercitydrew you can try resetting the transmission by getting in the drivers seat, close the door to the car, pressing the start button once (without your foot on the brake, do not turn the engine on) press and hold the accelerator all the way down to the floor for 30 seconds, then press the start button again (turning the car off), open and close the car door and then try turning the car on and see if the transmission malfunction disappears.
I have a 2005 645ci and I got the transmission malfunction light. The BMW doesn't do trans work and recommended new trans. My question is does the 750 have the same trans as the 645CI?
If it goes into gear sporadically check the connection in/on the trans for fluid contamination. Can cause communication issues between can bus and trans
I have a 2008 535xi battery had died tried to jump start did not work, i had the car towed home. I put the car in to neutral manually to move the car and now the shifter is flashing the neutral light. I replace the battery and the car still marking neutral and will not start. Any information would be a big help to get this fixed.
RIP Nipsey Hussle. This was his car
Wow really
@@dunnrite8299yea pussy…really
How you know
For real?
My dealership told me It wouldn’t be smart to replace my trans fluid & filter due to Viscosity differences and recommended my original life factory fluid was suited for my car. I have a 07’ 650i (E63) and It shifts a bit clunky. Other then that the cars great 91k miles
Recommendations by chance?
I was told the same thing by three different ASE certified mechanics!! They said once I flush it cause all types of transmission problems
Are you still have the same issue?
@@BellaNoir3 well a bmw dealership is trying to persuade me to replace the transmission for $8,000.. versus fixing the problem!! I was told by a sister company their trying to get a big commission check versus $1,500-2,000 they would normally make.. the car is still sitting at the dealership for six weeks, ill pick it up next month and leave in my driveway
What would make a 6hp28 blink the shifter indicator under 70% throttle?
This just pop up twice on my 2015 328i xdrive what do you think it maybe
Any way you can do a video on replacing the MAP sensor on the n63 7 series engine. I can't believe no one has done it. Thx.
thanks for this video you explained so well
My 2006 530xi shifts but does not engage the gears. Any thoughts on that before I mortgage my house for the repair?
Did you ever figure out the problem cuz I have a BMW that's doing the same thing right now
@@tiffanywilliams3242same did u ever figure it out
Can u just replace the fluid, by any chance the fluid may b low which causing the gears not to shift
Beautiful walk through video
Hi i do have x1 petrol engine when transmision oil is hot does change the gears why?
I have a 2012 740I and when I push the button simply to put it in park it goes to neutral with a message saying use the parking brake to ensure it doesn't roll. Consult a service center. Is there an easier fix?
I have a 750i it slams back into park at stops also gears in dash are blinking any suggestions?
update?
Sir you are very knowledgeable
I have a BMW 525 XI 2015 the transmission stays on natural and won’t start . Saying car in not in P . ? Anyway how to put it in P ?
Thank you for the video, you're knowledge is appreciated!
Please explain how to fix my trouble code...
I have 2011 750li 107k miles
trans code:
400126 - solenoid 3 (parking-lock holding magnet short circuit to ground or open circuit)
I have already replaced plug adapter,4 stem seals and bridge seal... Along with new pan/filter and trans oil.
Stl no fix
Hi
My BMW 2011 have Clutuch tempreatre problem even i change gear fluid and filter
Hi thanks a lot for the information. I have 2012 BMW740LI I just go to garage for change transmission oil change .they saying they will change but they not take any responsibility. they propose not to change. now my car run 140000km i buy this last year that time132000km drive. I asked that owner when the last time change oil he not remember. Please advice what shod i do. Thanks..
If I change Valve body. With solenoids and seals. But put my original tcm back on the new valve body. Do I need to code it still ?
Can you also make a video why my 2013 745Li when you put it in drive and goes back to Neutral and when you put it in reverse.
Hi I have a 2009 bmw 750i I have been getting a Transmission malfunction warning so I took the car to a indy in my area. When the car was first diagnosed it was sending a code that said the shift solenoid C was the problem so I purchased solenoids and transmission fluid, filter and all. My mechanic checked it out and said that it needed fluid. To make a long story short he tested the solenoids all of them were good so he added fresh fluid and a need transmission filter so he did that I went to pick up the car today and it was still showing transmission malfunction. Does anyone know if the transmission needs to be reset for it to work properly with the new fluid and all? Any help will be appreciated Thanks
I have a 2016 X6 BMW it grinds when I put into gear and won't move, but when I put it in nuetral the grinding stops... What can this be?
I have 328i 2007 bmw that you all can fix. It will not go into gear right
I have a 2012 bmw 750li xdrive. Motor and transmission were changed out now the trans won't shift out of park
I have a 2013 bmw 650i stuck in neutral it won’t even start up at all new engine new injectors and everything what could be the issue I need to drive my car please help 😔
Ok I got transmission problem error code 4E87 (solenoid valve 4 shift lock) any idea how to fix this?
Hi, I’m having the same issue with my transmission, have you figured out what’s wrong with yours ?
My 750 won’t go into P light flickers and go back to N and when I drive the car trans erratically switches gears back and forth like it has lost its mind, anyone has same problem ? Any solutions, ideas would be helpful, thanks
Any fixes? What happened?
You ever fix this problem??
I have the 750 I 2011 when it is cold it doesn’t want to shift what could be my problem once it’s warm it’s fine but I think the guild is low
Same here have you found out anything ?
Me also.
My 2007 BMW 525i will make a click sound in the actual gear shift then is stuck in z1st gear and won’t shift u til I turn the car off then it’s stuck in park and I use the gear shift release to out in drive but then it’s stuck in first gear again. Then I the. The engine off and on some times it will shift and be fine until I hear this click sound again and it’s stuck in first gear.
Hi Guys have bmw 2015 3series diesel automatic transmision 8gear.Question when I driving on M+S it’s says on the dash S7 but not showing 8gear.Is this normal or it should show S8 when I driving 140-160kmph.I thinking maybe it’s not shifting into 8gear.But drives no problem no lights on dash nothing.Can someone explain me please?
I have a 2014 BMW X1 HAS CODE 4EB3 VOLTAGE SUPPLY TO ETC , ONLY HAPPENS WHEN PUSHING OFF START STOP SWITCH, PLEASE HELP
CF19C1 amigo tengo ese error en la transmisión y me dice que tiene pérdida de potencia y que conduzca moderadamente, dice errores del grupo 3 durante la marcha de mi serie 5 BMW podrías ayudarme?
What does my 2015 528i twin turbo get this code 420641 while I'm driving and the auto engine button doesn't work but if i put the auto H button the problem with the gear changing to neutral and then to drive until i have to restart the car but if i have the auto H button it won't cause the problem as much but it still does it and then if i have the auto H on and turn on the sport or eco function it will go back to comfort and it won't go too fast or the turbo won't work properly. The code it gives me is 420641 and it only gives me the code whenever I that problem happens and i have to have the code reader connected to get the code but the code says that i actually pressing the Park button on while driving(moving car) why does it do that and i can't find no one that can actually fix it cause i live in a small county and the nearest bmw is 2 hrs away.
Hi Francisco, thanks for all the good educational videos on your chanel. I own a regular 2012 750LI and recenlty a transmission malfunction light came up and the car went into the safety mode you explained. I plugged in my Autel MK808 and 400341 popped up. The symtoms before the light came up was that the car will not shift properly in the lower gears and after hesitating for a few seconds it will shift normally and pick up a normal acceleration (no codes registered during those conditions) but today the code showed up. Have you had any experiences with this code? Is it a serious issue?
After watching one of your videos on how to replace the trans fluid and filter I feel confident that I can do it. What would you recommend I replace while doing that ?
any updates on the problem? i’m having this same issue
Good day. how can i send you a video? i want to send you a video clip of what i am experiencing on my 2011 BMW X6M gear, my gear jumps on the initial start. when the car is parked for a while, and you start it and put the gear on reverse or drive, it jumps to park((P) It jumps automatically to park, except u step on the accelerator pedal at the same time as soon as you select drive or reverse, then it will now engage in driving or reverse. But it doesn't jump while the car is already in motion, except when parked and the engine is switched off for a while.
My bmw X1 2017 gear box is ok but 4 th gear is not shifting
How do you change the transmission fluid
2012 750li xdrive motor and transmission were changed. Car starts with no problem but transmission stuck in park. Can anyone help me with this problem
Like your video, need help on BMW 2013 535iXdrive sedan M-sport F10 model
has Fault code 420321 gear shift ration monitoring gear shift 2 not plausible
What can I do? thank you Jorge
The gearbox is stage 2 can be software problem?
Hello. Solenoid valve 2 defective short-circuit to ground or open circuit code 400116. Start engine and put on driver and D flashing. Need only valve 2 charging?thanks
Outstanding ❤
Hi I need your help ...my f30 gearbox get water...the gearbox cooler broke so coolent lick into the gearbox...I removed the gearbox clean it up...now I have this fault code 420641: Parking lock defectively engaged...please help me please
Do you have a part number for that sensor?
What about fault code (400126)
completely off topic. anyone know what wheels those are? they are nice!
I have a BMW X5 2010 3.0 xdrive . The car goes into limp mode when going up an inclined road and when gear in changing from 4th to 5th. i notice because i put the gearbox into manuel and it always slips meaning the revs go high as if in free for a split of a second then goes into 5th gear. if its on automatic it would go into limp mode. The thing is i changed the gear oil and also the o rings and gaskets. Cannot understand if it's a solenoid or a gear . BMW cannot identify the problem telling me i need a new gearbox.... can this be the situation?
It also happend to me,BMW X3 ,2013
Yup me to goes into limp mode when it shifts into 4th gear if you drive it manually skip 4th to 5th and 6th can't remember to skip 4th back down but I've done it once and I've also changed all six silllinois and new fluid if I remember the megatronix which looked like it had a crack in it but I didn't really think much of it because it was just a piece of plastic that still functioned if anybody has any info that would much appreciated
I have a problem with my transmission can help me please I'm in California
Thanks!
Having some issues like this too ! Car stuck in park not shifting at all ! The light blinking ! Had the transmission replaced 8k miles before or less ! Any other suggestions?
What was it?
Megatronix
@@adamtorres8303 mines goes into drive, it's when I take off it slams back into park and gears on dash blinking would that be the same thing? Thanks for the response
Not sure what that may be , it could be software issue , mines back in shop again for it ! 🤦♂️🤦♂️🤦♂️🤦♂️🤦♂️
@@adamtorres8303 I took mines to the shop also and it was low on transmission fluid they raised it up more on the driver side when refilling and it took 2 more quarts after originally thinking it was full
Interesting...my transmission won't slide across to sport mode!
i got a 2000 bmw 528i it wont get out of first gear
My 2007 BMW 525i will make s click sound in the actual gear shift then is stuck in z1st gear and won’t shift u til I turn the car off then it’s stuck in park and I use the gear shift release to out in drive but then it’s stuck in first gear again. Then I the. The engine off and on some times it will shift and be fine until I hear this click sound again and it’s stuck in first gear.
B
Hello what state are you located in ?
What's up Francisco? I got this code on my 2013 740i this morning. I filled my car up Tuesday, it sat for a day and when I went to start my car this morning I got a rough idle and the transmission malfunction warning on the iDrive screen. I did not turn the car on, I gave the car a little gas so it wouldn't shut off during the rough idle and then my RPMs just settled out just below 1000RPMs. I let the car warm up, drove 25 miles to work, no problems. I will drive it home soon and I don't expect any issues. I scanned with my Autel MaxiCheck MX808 and I don't see any codes I should be reading. Do you know where I should look? Thanks in advance.
Clean your mass air flow sensor on your air box with brake cleaner
Where your mechanic location
I have an automatic car is doing funny things
First when selected Drive or Reverse it would just jump back on its own into Park.
Now its not doing that anymore.
Now when i select reverse it goes into reverse and as soon as i get close to something it was sound an alarm, but when i select Drive it goes into drive and goes forward . the alarm disappears but the reversing information is still on the dash screen even when i put in Neutral.
Hope i can get some help from you or someone on this chat
bmw 118i F20
That is a simple thing to fix. It’s distance based. The car displays the rear backup camera info when put into reverse, the information will not go away until you travel a far enough distance forward to make it disappear. Like 15 feet or something.
Where are you located
can i have your contact to fix my bmw 750i twinturbo
Where are you located?
Please let me know how I can contact you
I have a 2007 528xi it moves forward but won't go in reverse and also in P. When I press the P it goes straight in N it flickers but doesn't move as if it's already in Park. The only time it starts moving in reverse for a little bit is when I reset the transmission module. What should I look into? Could it be the solenoids or something else? Thank you
Hi halil
I’m experiencing the same problems with my Transmisoon 530i
How did you fix the issue
Any advice will be very helpful
Thanks in advance
You fix it it
I have a 2012 740i BMW replaced my bad battery and now my bmw don’t want to go into gear ⚙️ transmission malfunction sign pop on my dash…bmw told me it’ll be 10k to get a new transmission…i believe that’s bullshit cause my car didn’t have transmission problems after they placed the new battery in…so it’s just parked outside my home and still runs but won’t go into gear…I need help & information on what to do next
They didn’t damage your car. It happens to all cars at some point not just bmw
@@Sequel7 so what to do now?
@@choppercitydrew you can try resetting the transmission by getting in the drivers seat, close the door to the car, pressing the start button once (without your foot on the brake, do not turn the engine on) press and hold the accelerator all the way down to the floor for 30 seconds, then press the start button again (turning the car off), open and close the car door and then try turning the car on and see if the transmission malfunction disappears.
I've done that twice and it
Of the net twice and it violently shifts past four and coming down back to tcm
Can anyone help me with this problem
what city are you located at? might just come bring my car to you 😂
Can a bad camshaft sensor cause transmission malfunction?
No
Yes
TCM code bmw 740d 401071 I need help
I have a 2005 645ci and I got the transmission malfunction light. The BMW doesn't do trans work and recommended new trans. My question is does the 750 have the same trans as the 645CI?
If it goes into gear sporadically check the connection in/on the trans for fluid contamination. Can cause communication issues between can bus and trans
Happy secure grateful blessed
Seria tanbien bueno que lo esplique en español
No mames wey😂
Oh and I have no transmission error on my screen
Creo no ay problema si lo explica en español y que le ponga subtítulos n inglés
Ya esas son mamadas las tuyas😅😂😂😂😂😂
Sorry BMW 528i
🏁🏁🏁
Sir
I have BMW 740li ptrol
Gear not shifting properly what reasin8
Callese wei
This codes are for a bad battery friends? E088 E094 transmition malfunction... my car starts but my dct don't starts. Thank you much.
I have a 2008 535xi battery had died tried to jump start did not work, i had the car towed home. I put the car in to neutral manually to move the car and now the shifter is flashing the neutral light. I replace the battery and the car still marking neutral and will not start. Any information would be a big help to get this fixed.
Did you solve it?