DIY knife parting tool from an old table saw blade
HTML-код
- Опубликовано: 9 сен 2024
- In this video I make a knife parting tool out of an old table saw blade and a piece of mahogany. This tool is used to part off thin pieces of wood when woodturning.
Tools and materials I propose:
Angle grinder: amzn.to/2E6uLAx
Metal cutting discs: amzn.to/2Wzcn85
Drill press: amzn.to/2pJaAPo
Flat file: amzn.to/2RHIMHH
Propane torch: amzn.to/2NGa3XP
Belt sander: amzn.to/2QK0TeN
hacksaw: amzn.to/2ywuMYP
Chisel set: amzn.to/2pILO1B
Block plane: amzn.to/2RLiAMf
Spoke shave: amzn.to/2IjIALM
Mini machinist’s lathe: amzn.to/3hR3wJT
Jeweler's saw: amzn.to/3j53MG9
Disclosure: Some of the links below are affiliate links, meaning, that at no cost to you, I get a small commission if you click through and make a purchase.
You can also support my channel by getting a T-shirt: tinyurl.com/y8...
For more information about this project, go here:
tinyurl.com/24...
----------------------------------------------------------------------------
You can support my channel through Patreon:
/ scrapwoodcity
----------------------------------------------------------------------------
For more scrap wood projects, please visit my blog:
scrapwoodcity.b...
My social media channels:
Facebook
/ scrapwoodcity
Pinterest
/ scrapwoodcity
Instagram
/ scrapwoodcity
twitter
/ scrap_wood_city
#DIYtools #woodturning #κnife
Lovely. Minimalist and straightforward.
Thank you
The essence of recycling!
Well done!
Thank you, I hope so!
Bravo that's a great tool
Thank you
Nice build. We featured this video on our homemade tools forum this week :)
Awesome! Thank you!
Magnificent job, as always. Thanks Dimitris.
Thank you my friend
Πολύ ωραίο αποτέλεσμα!!! Μπράβο Δημήτρη!!!👍
Ευχαριστώ Μιχάλη
Το αγαπημένο μου εργαλείο! Χιλια μπραβο φοβερή δουλειά όπως πάντα
Ευχαριστώ αγαπητέ
When riveting make a rivet head plate by drilling a hole in a piece of three eighths steel plate the size of the rod stock you are using then use a counter sink drill bit to form a counter sink throat like a funnel
To form a head first lay your head plate on vise insert the rod through the hole with about an 1/8" above the plate and grip in vise and then use a dall peen hammer to form the shoulder of rivet
Countersink the holes in handle scales
To used the rivet place through the handle and place head side down on anvil and leave about the same amount protruding as you used to form the head using the ball peen hammer peen the head down using strikes around the rod to peen the head into the countersink and tight to the scales file flush and done
headless rods will not hold even when epoxied
Nice thin parting tool
Το βρίσκω εξαιρετικά δημιουργικό να μπορείς να ανακυκλώνεις και να γίνονται πάλι χρηστικά αντικείμενα !!!!! Κακώς δεν έχεις κάνει site να τα πουλάς (όπως την ματσόλα από χαλκό) Πολύ ωραία δουλειά !!!!!!!!!!!!!!!!!
Σε ευχαριστώ Κατερίνα κι εμένα μου αρέσουν αυτά τα πρότζεκτ
Big like!👍👍👍👍👍✅💪Felicitări! Great video 👍👍👍😎
thank you
Πολύ ωραίο Δημήτρη. Να φτιάξεις ένα ταινιολειαντηρα είναι πολύ χρήσιμο εργαλείο για κατασκευές
Ευχαριστώ Στέλιο. Ο ταινιολειαντηρας που έχω μου είναι αρκετός. Θα ήθελα καλύτερο αλλά προσ το παρόν δεν είναι προτεραιότητα για εμένα. Ειδομεν.
Curious question. Why didn't you use one of the carbide saw teeth for the tools cutting edge?
Actually I want to try this at some point. But I wanted to make the classic knife and be able to sharpen it multiple times. I was a bit skeptical on sharpening carbide teeth.
@@ScrapwoodCity Cool. Thank you for the reply. I really like the channel and your creative approach. Subscribing now. :-)
Thank you
nice
Thank you
Very cool. I love how you recycle old materials. I have a few old sawblades that I'm keeping for a knife project myself. Any tips for a first-timer?
Thank you. Nothing special it was a nice material to work with. Not too hard not too soft. Just place your design in such a way so you don't waste too much steel from the blade.
Expense to income.
GooD)))))))
Thank you
Great tool. Why didn’t you save and use the carbide tip end for the cutting edge?
Thank you. I wanted to he able to sharpen it for a long time. And also I don't trust that the carbide tip will stay there for ever. So, in my mind this option was never in my intentions.
@@ScrapwoodCity Thanks for the explanation.
Ωραιος ο φίλος. Και το βίντεο πολυ καλο..
Πιστευω όμως ότι ένας ταινιολειαντηρας θα σου λυσει τα χέρια...
Η λαβη σε ταλαιπωρησε αρκετά..
Ευχαριστώ. Μπα η λαβή ήταν το εύκολο. Θα ήθελα ένα ν καλύτερο ταινιολειαντηρα αλλά δεν το βλέπω για σύντομα
@@ScrapwoodCity prioritys... Όπως και
να'χει και παλι μπράβο για το βίντεο..
could you not have used one of the teeth as the cutting edge.
Perhaps I could, but I decided to go for the classic knife. Interesting point though.