Это видео недоступно.
Сожалеем об этом.
Bialetti Moka Express percolator gasket replacement
HTML-код
- Опубликовано: 11 май 2021
- When your percolator starts leaking on the side, it is an easy gasket replacement. This is a stove-top 3-cup Bialetti Moka Express Iris but the same replacement instructions work for almost any percolator of this type.
Also view my "how percolators work" video.
• How Stove-Top Percolat...
And my video where you actually get to see it work.
• How To Make Espresso w...
This was really helpful! My moka pot started leaking and I was real intimidated about how to fix it. Thanks for instructions and the humour!
welcome
"you need a very complex tool...a butterknife" 🤣
Just made and saved my Morning, appreciate it 💪🏻
Very helpful. Rehabilitating my knock-off moka pot after accidentally leaving it on the burner for over an hour! Gasket melted onto the metal and residual coffee in the reservoir looked baked-on. Took steel wool to it and ordered the gasket/filter replacement. Just watched your video and installed and I'm ready to roll for tomorrow morning! Thanks!
very welcome
That’s so funny! That is exactly how I stuffed up my pot too! Left him on the stove while talking on the phone to an old friend in the US 😂
@@kyliewalker6647 Well, you have a better excuse. I just neglected to turn the stove off. Later, I kept thinking, man the coffee aroma sure lingers! Not realizing it was cooking the whole time!
Great thanks for the explanation ! Have a great day ! and I love your sense of humour
Very helpful thank you very much ! There is so no notice in the packet like it's totally normal to know how to replace this XD 👍🏼👍🏼👍🏼👍🏼❤️
Wow, replaced mine, it IS that simple. The lower half, when screwed in to position, secures the gasket which in turn secures the upper filter.
Hence no adhesive required.
Thanks.
And thanks AliExpress.
You are welcome.
Yes, you can get gaskets from a lot of places but AliExpress has a handy gasket chart that helps you figure out which one you need.
Very helpful video. If only I had a very complex tool to pull it off 😉
Thank you for the vid! this was super easy.
Have a little one cup and the gasket is totally worn out
You’re very welcome. Thanks for liking it
Glad I saw this before buying a new bialetti thanks!
Nothing wrong with having a 6-cup bialetti for guests anyway. In my other video I show the 10 or so immediate ones in front of me but I have like 50.
Thanks for making this entertaining, helpful little vid. I wish I’d seen it before replacing my whole moka pot..😩
welcome
Brilliant. Thank you 👍🏻
Very helpful. I will give it a go.
You are a brilliant teacher! I'd love to see how you make a coffee in your Bialetti- I mean I know they're all the same but I imagine we all have slightly different ways & preferences in our coffee rituals 😊
Thank you. Very kind of you to say
this is the link to my coffee making video. ruclips.net/video/iORcokydMzE/видео.html
Thank you! That was super easy! 😊
welcome
exactly what i needed!! thankyou mister
You are very welcome.
Omg thank you, I was spending way too long on this on my own haha
glad it helped.
Thankyou! Very useful tutorial.
yw
Good Lad. Thanks☕
Thank you so much x
Thanks so helpful🤗
you are very welcome
Thanks for the video. I was about to throw my old bialetti and buy new one
Brilliant thank you so much
you are very welcome
Thank you for that yseful entertaining little vid !
One little detail to add i think that second filter is made out of inox
that may depend on the pot you're using. I have some pots where it's full stainless steeel. But thankyou for the info
Super
Thanks ❤
thanks, super helpful
you're welcome
Thank you 🙂
y welcome
Thank you
welcome
Thanks, I'll get a replacement gasket. Mine fell apart after the first use. Question, I read that the flame or heat source should not be wider than the bottom of the pot. I have a gas burner but doesn't work well on your electric stove top? Is the heat only as small as the base? Or does your handle get real hot?
There are a few issues with flames. You should not have flames high because it's a waste. If you look at the flame "points" - the cone point of the gas stove flame is the hottest point. You should lower the flame height so the points approximate hitting the bottom of the base. If the flames are too high, you are heating the edge of the pot above the base. You also run the risk of damaging the handle. Here is a simple youtube vid where you can watch where the flame is hottest. ruclips.net/user/shortsvlRGGhJOWwQ
As far as using an electric stove, I actually use one but every electric stove is different so you have to figure what works for you. A standard three cup percolator should take between 8 and ten minutes as shown in this video ruclips.net/video/iORcokydMzE/видео.html
You should NEVER heat the poy too fast or too high or too long beacause you could damage the gasket, the handle, the cap nub or the pot itself. But what you are most concerned about with heating the pot to quickly is that it would not give enough time for the water to soak the ground which would cause pressure build up and the escap valve being released. This video talks about how percolators work and talks about the valve. ruclips.net/video/v6XufjVtkb4/видео.html
Hi! How many brews you have to do to the coffee go as it was brewing before the replacement? For me, always it takes like three brews to be ok. At the last one, it for sure is most than 15 times and aren't good enough. Thank you!
Sorry, I am not sure I understand the question.
I have gone years before replacing the gasket. That is hundreds of uses. You don't really need to replace it until it's leaking, or if you feel like you want to.
Good man, people who take care are more sympathic to me :))
Great thanks -- is that a "6-cup" or 3-cup coffee maker -- and does it matter when ordering new gaskets?
Mine was a three-cup and it does matter when you order gaskets
I replaced my filter and gasket and the espresso grounds are making it into the pot now. Any tips?
is it possible you put the filter upside down? During my video I said, "not like this" then flipped it over and said "like this". The other possibility is you are putting the coffee directly in the base instead of the lower filter - I've seen that done before. In the bottom of my comments is a limk to a video on how to make it. Please check if you are doing it right.
Btw you're supposed to regularly take the filter out and clean under it... Otherwise coffee ground and stuff get stuck in there with time, which is gross.
you saw my pot. There were no grounds at all. Just a little bit of patina. If you have grinds beyond your upper filter, you probably need to get a replacement upper filter. The water going through there is high temperature. Nothing could live through that. The only concern would be if you didn't clean it and just left it closed with old grounds in it for a few weeks. Sometimes people put them aside without emptying the ground because they forget. The moistness can cause the upper or lower filter to corrode and could have some mold. But other than that, it should be fine.
Comment changer la poignée en plastique svp apparemment c'est très difficile
Probably not worth replacing the plastic handle. I would say send it back to the company.
I was looking for a solution after I damaged the rubber thing . I order a replacement and it didn't fit iam searching for a solution 😅
different companies have different size rings and I don't know what size of coffee maker you have. Mine is a 3-cup. It helps to know that each cup is 1 1/2 to 2 ounces. Figure out the name of the company, give them a call and they should be able to help you figure it out.
@@scyberclops thanks .
I took the upper seal off rather than the lower seal and the replacement doesn’t fit. Either that or I got the wrong size. The lower seal fits fine, actually, kind of loose😢
I don't know what you mean by upper or lower seal. There is only one seal where the basin screws into the top. What brand and size coffee maker do you have?
Could be about 1.5 minutes long but America says no....