Perfect Preload Balance WITHOUT using a Tweak Station
HTML-код
- Опубликовано: 12 июл 2016
- No need for that expensive and hard to use tweak station.
Using only your existing ride height, droop gauge & setup wheels you can now get all your suspension preloads & corner weight balance perfect.
By following this tutorial you will see how easy and fast it is using existing tools compared to buying the likes of a Hudy tweak station.
Once you learn and understand this, it will only take an extra 2min to check and adjust while at the track
Gotta love content creators, a lifetime of knowledge and experience given away for free to the unworthy. This is one of the best setup videos I've seen.
Glad you enjoyed it Justin - I actually have a few more videos I'm creating at the moment which you will also like. Common sense setup stuff made easy!
Amazing info. Watched 2-3 times to get an understanding with my TC. Thanks for making an informative video for the masses. 👍🏼
No problems : )
Thank you for posting this video. It is very helpful to me.
Fantastic method, demonstration, and verification. Thanks!
Hi Tony, wonderful video. A suggestion....maybe could help. The system you propose is perfect, the most difficult part is understanding exactly when you pic up one side and the other lifts from the ground. If you put a small sheet of paper resting under the wheel that should stay on the ground, lift the other side and put it resting on the stepped gauge, then try to move slightly sideways the car..until you have load on the wheel it will move the paper, step the car one step higher and move slightly the car, the wheel will lift from the paper and you have an exact and constant measurement. Simplicity lifting the car until the other week lift is a little less precise, with thin system your tolerance is equal to the thickness of the sheet of paper and you do the settings whit the car perfectly still sitting on the stepped gauge. Hope it helps. Thank you for your great video. Donald
Good idea, I'm actually developing a tool to better and more accurately replace my hand and be still so precise corner tweak can be measured.
This is great! I used this method on my tamiya cars. I had my droop at uneven heights and turned out the preloads were screwy. Is it necessary to weight balance if the preload balance is set?
Hi thanks for great clear and helpful video. I did remember reading somewhere also about checking 1st with anti r b disconnected. Is this necessary? Kind regards Jon
Thank you.
Would this work on the infraction thanks for this even if it doesn’t work on that rig this is always good stuff to know 😎
Kindly to check the spring preload. Do I have to remove the torsion bar or sway bars?
Something else I normally put a screw driver in the middle of the rear and lift to see that both wheels touch the surface together and adjust the drop screws according to adjust the rear.
Same procedure to the front.
When I tried it on a flat levelled surface with two bars underneath the chassis like you did, I found a big difference on one side, and I am confused which system I should use to adjust them!
My rig is an Arrma Limitless, and it weighs about 6kg with batteries.
It's a bit heavy that is why I use a large screw driver to lift up!
Thank You for this Video! .. recent A700 owner here, theres alot to learn but i Love it. Very very helpful .
. Wishing there was a droop setting video to follow also. Question, the rubber grommets on the body posts? do you have a linkee to those or where to find? Sweet Car, beautifully done, I tried to mimic yours in my build process.
Those black grommets are from a local electrical store haha
Quick question here, don't you need to check left to right balance first before this technique will work?
There is an easier way to this. Use a long tool to raise the end of the car directly in the centre such as the middle bumper screw. If one wheel lifts early then use opposite shock preload to adjust.
This is the method I use, and is MUCH easier and faster.
Joshua Dolim The way you are doing it is not even accurate mate. Unless you have a rock steady hand ( which no one does ) you are gonna be well off.
neontetra1000 tell that to Martin Hudy.
I find that applying corner to corner method (My way) gives a far better result than lifting 1 end of the car as this now takes the weight of the whole opposite end of the car and not each corner individually. Your way (Martin Hudy's) is faster but not as accurate.
would the preload and ride height being off explain why my A700 wants to spin out when i make left turns ?
yes this can be 25% of the problem, it could also have air in one shock, tweaked chassis, unglued tire, a binding suspension arm....check all of these and let me know what you find :) I normally find a tire has unglued itself when it all of a sudden wants to spin out turning one way.
Let me know
is there a super secret tool to use to adjust the end bell timing with the longitudinal motor set up or just remove and replace motor and or ESC every time?
Hey, yeah that is a bit of a problem, but you just have to unscrew motor from the chassis and then flip it over then you can adjust :)
followed this and just shaved 3 seconds off my lap times :) thank you !
Is this info exclusive to the awesomatix system or will it also work for my BD8?
Hi, it works on all RC cars, the theory relates to all chassis's
Hi great vid fresh to see ,
Could you point me in the right direction to get this a700
Tried the official and usual distribution no luck
try www.rcmaker.com.au and contact Ryan. He will be able to source one for you
I haven't raced for a while but thinking of getting back. But when you adjust the diagonal tweak, from I recall, you adjust shock collar, not preload screw. And you had set droop already with preload screw. I don't know maybe I'm confused because I'm not familiar with Awesomatix at all. But I do remember, Awesomatix's shocks are laid down around lower suspension. Is that why?
Will ride height be different after these adjustments?
Yes, but as explained in the video, once all the preloads are set in each corner, you can simply adjust the each corner exactly the same amount up or down and the ride height will drop or rise keeping the pre load settings
What if you measure the front and not the other front wheel comes up but the rear wheel
You are effed at that point!
what is the total weight after all is installed?
about 1400grams
what's the brand/name of this chassis?
Awesomatix A700 EVO
I just assemble and drive and tweak over feel i have a really old mugen nitro subaru rally Car from the 90s that i have rebuilt and she is beutiful (btw does any body know where to buy 49mm dogbone bcus i broke one in half)
If you know any hobby machinists they can make you anything, and 10times the initial quality of most molded plastic parts. And most hobby machinists would like the challenge. Especially content creators
What rc is that
Awesomatix shaft drive
What brand of car is that??
Awesomatic A700