I have just pitted the E010 against the JJRC R010 using my Jumper T-lite 🎮 These are both toy-grade angle-cruisers 🚁 at around the same price range of 15,-💲 And THE R010 JUST OBLITERATED THE E010! 😮😲🤖 The R010 has substantial less deadzones and digital rates which makes it so much more fun to fly. And thanks to the 716 motors it can carry a large battery and camera reasonable comfortable. Noise production is a bit more than the E010, but not as annoying as some 2 bladed toy-grade drones. Really amazed with this flyer. If you can your hands on a R010, you can bind it using Type: Bayang, subtype: STD. I can fly blue and red variants of the R010 with this protocol.
When flying, keep your Jumper T-Lite on page 2. Because every time you swap batteries you have to bind to the drone again 😬 Or you could just switch the Jumper OFF and back ON again 😋 Then it auto-binds as part of its startup procedure 😁
I presume you have the multi module protocol on your Jumper T-Pro. For the E010; create new model and start looking if you have the E010r5 protocol. Its on Pag 2, under the [Mode - Multi] section, look for Type and change it to E010r5. If not present you might have to update your Multi Module Protocol: www.multi-module.org/using-the-module/firmware-updates/update-methods Keep me posted. Getting an E010 off the ground with a fancy schmancy controller is always fun 🥳
Creds go to Albert Kim. He told me to update the Multi-protocol Module in hope to get the E010 working on the Jumper: ruclips.net/channel/UCnJyFn_66GMfAbz1AW9MqbQ
Is [p2] ( switch position 1- [2]-3 ) the starting value for switches A & B for this drone? Or for that; on any “toy-grade” protocol I want to bind to? 🙄
I can get mine to bind under MJXQ then E010 but none of the switches do anything, flies great etc. Under the E010r5 It won't even bind... Any help? Thanks for the vid btw!
MJXQ??? Check your E010! I’ll bet you it’s an older GREEN board and not a RED board? About your [S]witches not working: Did you SETUP INPUTS (pag5) & MIXES (pag6) for CHANNEL 5-6-7-8? = [S]witch A-B-C-D? If you create a new Model on your Jumper T-Lite these are left blank. After configuration it should look something like this: CH1-100%Ail, CH2-100Ele, CH3-100Thr, CH4-100Rud, CH5-100SA CH6-100SB CH7-100SC CH8-100SD.
Specs @ Banggood tells us default "flying range" is 30m. (Maybe more once it is binded with a better transmitter like the Jumper T-Lite.) Never tested range because it is always windy outside. Also, in all practicality, at a distance of more than 10 meters, you can hardly see this tiny drone anymore. I find the E010 to be an exclusive indoor flyer, whereas penetration-power of the signal is more important. In that regard I can tell you it is pretty good and hardly susceptible to interference. You can do FPV with this unit, but flight-control will fell robotic, because of the huge deadzones and digital rates.
Red PCB flight-boards on the E010 are the newer and current standard. Green boards are becoming pretty rare. If you have one, best to hold onto them. I wish I had some in my collection. From what I gather; RED Board is way superior regarding connectivity and multi module protocol support. A step up from green.
@@petereuvideodrones oh ok thanks cuz i got jjrc h36f drone and its red board to, and ye i have 3 drones with green board cuz they are old and 1 motor doesnt work
I use the E010-r5 protocol, which wasn’t present on my (JP4in1) Multi-Protocol Module when I received my Jumper T-lite from the store. I had to flash my Multi-Protocol Module from “1.3.1.78 aetr" to "1.3.2.61 aetr” (using a max 32GB mini SD-card). OpenTX (the OS of my transmitter (v2.3.11) I didn’t touch. I guess you can also use the “OpenTX companion App” to update the Multi-Protocol Module, but that method is so over-complicated. Whatever you do, just make sure to shorten the filename to 7 characters on the SD card: downloads.multi-module.org/
@@NWDestroy Np, btw, here's a "little" tip: I have just pitted the E010 against the JJRC R010 using my Jumper T-lite 🎮 These are both toy-grade angle-cruisers 🚁 at around the same price range of 15,-💲 And the R010 just obliterated the E010! 😮😲🤖 The R010 has substantial less deadzones and digital rates which makes it so much more fun to fly. And thanks to the 716 motors it can carry a large battery and camera reasonable comfortable. Noise production is a bit more than the E010, but not as annoying as some 2 bladed toy-grade drones. Really amazed with this flyer. If you can your hands on a R010, you can bind it using Type: Bayang, subtype: STD. I can fly blue and red variants of the R010 with this protocol. Lator 🤖
No: github.com/pascallanger/DIY-Multiprotocol-TX-Module/blob/master/Protocols_Details.md Just get the JP4in1, it’s only 10 bucks more and you will adding an incredible range of possible protocols. Good luck.
I have just pitted the E010 against the JJRC R010 using my Jumper T-lite 🎮 These are both toy-grade angle-cruisers 🚁 at around the same price range of 15,-💲
And THE R010 JUST OBLITERATED THE E010! 😮😲🤖
The R010 has substantial less deadzones and digital rates which makes it so much more fun to fly. And thanks to the 716 motors it can carry a large battery and camera reasonable comfortable. Noise production is a bit more than the E010, but not as annoying as some 2 bladed toy-grade drones. Really amazed with this flyer. If you can your hands on a R010, you can bind it using Type: Bayang, subtype: STD. I can fly blue and red variants of the R010 with this protocol.
Dank je voor de video! Nu kan mn dochterje mooi vliegen met haar e010 en de jumper t-Lite : )
When flying, keep your Jumper T-Lite on page 2. Because every time you swap batteries you have to bind to the drone again 😬 Or you could just switch the Jumper OFF and back ON again 😋 Then it auto-binds as part of its startup procedure 😁
Can you do this with Jumper T-Pro, and if so can you give a detailed instruction for a nub like me.
I presume you have the multi module protocol on your Jumper T-Pro.
For the E010; create new model and start looking if you have the E010r5 protocol.
Its on Pag 2, under the [Mode - Multi] section, look for Type and change it to E010r5.
If not present you might have to update your Multi Module Protocol:
www.multi-module.org/using-the-module/firmware-updates/update-methods
Keep me posted.
Getting an E010 off the ground with a fancy schmancy controller is always fun 🥳
@@petereuvideodrones Thanks I am going to try it soon.
Hello Peter,
Just passing by to say THX for sharing.
Happy flight,
Creds go to Albert Kim. He told me to update the Multi-protocol Module in hope to get the E010 working on the Jumper: ruclips.net/channel/UCnJyFn_66GMfAbz1AW9MqbQ
Is [p2] ( switch position 1- [2]-3 ) the starting value for switches A & B for this drone?
Or for that; on any “toy-grade” protocol I want to bind to? 🙄
I can get mine to bind under MJXQ then E010 but none of the switches do anything, flies great etc. Under the E010r5 It won't even bind... Any help? Thanks for the vid btw!
MJXQ??? Check your E010! I’ll bet you it’s an older GREEN board and not a RED board?
About your [S]witches not working: Did you SETUP INPUTS (pag5) & MIXES (pag6) for CHANNEL 5-6-7-8? = [S]witch A-B-C-D? If you create a new Model on your Jumper T-Lite these are left blank. After configuration it should look something like this: CH1-100%Ail, CH2-100Ele, CH3-100Thr, CH4-100Rud, CH5-100SA CH6-100SB CH7-100SC CH8-100SD.
What the range ?
Specs @ Banggood tells us default "flying range" is 30m. (Maybe more once it is binded with a better transmitter like the Jumper T-Lite.) Never tested range because it is always windy outside. Also, in all practicality, at a distance of more than 10 meters, you can hardly see this tiny drone anymore. I find the E010 to be an exclusive indoor flyer, whereas penetration-power of the signal is more important. In that regard I can tell you it is pretty good and hardly susceptible to interference. You can do FPV with this unit, but flight-control will fell robotic, because of the huge deadzones and digital rates.
What is the difference red board and green board?
Red PCB flight-boards on the E010 are the newer and current standard. Green boards are becoming pretty rare. If you have one, best to hold onto them. I wish I had some in my collection. From what I gather; RED Board is way superior regarding connectivity and multi module protocol support. A step up from green.
@@petereuvideodrones oh ok thanks cuz i got jjrc h36f drone and its red board to, and ye i have 3 drones with green board cuz they are old and 1 motor doesnt work
@@ignastravels9346 Good news, you got the older (softer) frame. Much easier to replace motors. How are you solder skills?
@@petereuvideodrones never solder before 🤫
can it bind to flysky i6 for red board?
I'd wish, but no. You need a multi-protocol module for that. Integrated or external.
Dang, I can't get mine to bind to my T Lite... what protocol are you using?
I use the E010-r5 protocol, which wasn’t present on my (JP4in1) Multi-Protocol Module when I received my Jumper T-lite from the store.
I had to flash my Multi-Protocol Module from “1.3.1.78 aetr" to "1.3.2.61 aetr” (using a max 32GB mini SD-card).
OpenTX (the OS of my transmitter (v2.3.11) I didn’t touch.
I guess you can also use the “OpenTX companion App” to update the Multi-Protocol Module, but that method is so over-complicated.
Whatever you do, just make sure to shorten the filename to 7 characters on the SD card: downloads.multi-module.org/
@@petereuvideodrones thank you
@@NWDestroy Np, btw, here's a "little" tip: I have just pitted the E010 against the JJRC R010 using my Jumper T-lite 🎮 These are both toy-grade angle-cruisers 🚁 at around the same price range of 15,-💲 And the R010 just obliterated the E010! 😮😲🤖
The R010 has substantial less deadzones and digital rates which makes it so much more fun to fly. And thanks to the 716 motors it can carry a large battery and camera reasonable comfortable. Noise production is a bit more than the E010, but not as annoying as some 2 bladed toy-grade drones. Really amazed with this flyer. If you can your hands on a R010, you can bind it using Type: Bayang, subtype: STD. I can fly blue and red variants of the R010 with this protocol. Lator 🤖
Can cc2500 bind ?
No: github.com/pascallanger/DIY-Multiprotocol-TX-Module/blob/master/Protocols_Details.md
Just get the JP4in1, it’s only 10 bucks more and you will adding an incredible range of possible protocols. Good luck.
Hurrah! 🥳 My E010 Stick Extensions have arrived 🤖
If you need some user-feedback: ruclips.net/video/6ZTVr5aHI8U/видео.html