Hello ... If you please I have one question . I have this device on job and I making balancing of big ventilators of primary air in coal power plant , also on others ventilators if it is necessary . One thing drives me crazy . I know when we creating input data in to device , particulary angle between vibrations sensor and optical sensor we take angle between those sensore in oposite direction of rotation. Like example vibration sensor I put verticaly on bearing housing , optical sensor I put on horisontal position on shaft , oposite of rotation , angle will be 90°. But I expirienced crazy situation on some other ventilators , that rottating in same direction , sensors are in same positions but weight going contra - for 180°. So in that case I know that I am made mistake and I puting weight in frst step on contra side . But that makes trouble for the final weight , it brings me in position to not believe in my countering of right angle .
Dear emir džibrić , First of all, thank you very much for your comment. As it seems, you have run into severe issues. Please let us help you get the best quality work from your efforts. Please contact us through our website www.pruftechnik.com/com/Products-and-Services/Services/Technical-Support/, and we will come back to you right away to solve your issue. Best regards, Your PRUFTECHNIK Team
Try putting the trial weight -135deg from max out of balance. Angle is measured keeping rotation in same direction. It looks reverse because we are measure angles on the moving component. I try to set up the phaser inline with a marked starting point '0'. It's just easier.
Dear khaled G, First of all, thank you very much for your comment. There are two easy ways to find out about the answer to your issue. Either you take a close look into the manual or drop us a line on our contact-site: www.pruftechnik.com/com/Contact/Sales-Contact/Contact-form/. We are likely to help you in any case. Best regards, Your PRUFTECHNIK Team
I use one of these and as long as the fan behaves, one shot balances are often done. Actually there are 4 runs. As found, trial, trim and check. No way out of that. And some times many more eh!
Very nice! You should send some of those jackets to us in Johnsonburg PA.
Is the tachometer location important relative to the viberation sensors?
Hello ... If you please I have one question . I have this device on job and I making balancing of big ventilators of primary air in coal power plant , also on others ventilators if it is necessary . One thing drives me crazy . I know when we creating input data in to device , particulary angle between vibrations sensor and optical sensor we take angle between those sensore in oposite direction of rotation. Like example vibration sensor I put verticaly on bearing housing , optical sensor I put on horisontal position on shaft , oposite of rotation , angle will be 90°. But I expirienced crazy situation on some other ventilators , that rottating in same direction , sensors are in same positions but weight going contra - for 180°. So in that case I know that I am made mistake and I puting weight in frst step on contra side . But that makes trouble for the final weight , it brings me in position to not believe in my countering of right angle .
Dear emir džibrić
,
First of all, thank you very much for your comment.
As it seems, you have run into severe issues. Please let us help you get the best quality work from your efforts. Please contact us through our website www.pruftechnik.com/com/Products-and-Services/Services/Technical-Support/, and we will come back to you right away to solve your issue.
Best regards,
Your PRUFTECHNIK Team
@@PRUFTECHNIKGroup ok
Try putting the trial weight -135deg from max out of balance.
Angle is measured keeping rotation in same direction. It looks reverse because we are measure angles on the moving component.
I try to set up the phaser inline with a marked starting point '0'. It's just easier.
Good ..👍👍
What's the incoming trigger and the outgoing trigger?
Good on ya Tom
EXCELLENT
Hi guys. I am about to start using VIBEXPERT II , I just want to know, can the RPMs be entered manually, or an RPM sensor is a must have?
Dear khaled G,
First of all, thank you very much for your comment. There are two easy ways to find out about the answer to your issue. Either you take a close look into the manual or drop us a line on our contact-site: www.pruftechnik.com/com/Contact/Sales-Contact/Contact-form/. We are likely to help you in any case.
Best regards,
Your PRUFTECHNIK Team
@@PRUFTECHNIKGroup Thank you for your help.
Price
How much for this type
Hi Abdo,
For information on pricing as well as our other vibration products please visit our website at: bit.ly/3rdkxCQ.
Asking price.
1 and done with a weld on weight??? lol I call bs. Nice demo tho. Hell of a lot better price point than the CSI 2340 I'm using.
I use one of these and as long as the fan behaves, one shot balances are often done. Actually there are 4 runs. As found, trial, trim and check. No way out of that. And some times many more eh!