I've always been afraid of popping things out and removing screws and stuff. I rather just pay a professional to do it for me.. Yeah I know I'll save $$$ the way I see it is since I'm very impatient and liable to break something, I'll end up paying more when I have to buy the replacement part.. Looks nice. I might give it a try on my '19 1.5. Seems easy enough I guess.. Wish me luck.
Maybe instead of having a defeatist attitude you can learn and practice using a screwdriver and changing a lightbulb lol it’s not that hard, have some confidence and don’t rush yourself.
thank you so much, jon for this and all your vids. sincerely appreciate how you anticipate the problems we may face and your walkthroughs are easily the most diligent and easy to comprehend. oh, 8mm socket works perfectly to get the screws out as well👍
Thank you Jon ... I ordered these from Amazon ... these were like $15.00 more than most others on eBay but you advised there is a lifetime guarantee . The other brand led turn signal I bought previously , lasted a year and half and they only offer 6 month warranty . So I figured these have a better warranty ... you mentioned life time and I order these from ALLA ... I was checking on the order and read their website .. they list 1 year warranty... but I trust Honda Jon ... and you’ve had a good experience with these from ALLA . I hope I do too
Why did Honda redesign such a lame way of changing out the bulb? i own a 2002 and 2016 Accord and all i have to do is pull back the rear trunk liner where the rear tail light housing sits and vola, it's there and easy to get at. btw i had to change out the rear flasher on my 2016 Sport also because the original were way too faint. The replacement rear flashers were fantastic, extremely bright. iJDMTOY (2) No Resistor, No Hyper Flash 21W High Power Amber 7440 W21W T20 LED Bulbs For Car Front or Rear Turn Signal Lights .
Are you still running these? Normally aftermarket LED turn signals are extremely bright and could easily blind people behind you - prior ones I have tried seem dangerous to use because they are simply too bright. I wish there was a standard brightness LED light. I don't need the "headlight" brightness, just instant on/off.
Not sure if they make white ones but you can find them on Amazon. The trim is not hard just tricky. Keep trying on one side as you push the trim part against the light. Eventually you’ll get it to snap in. It’s the weirdest design.
I like your accord. You didn’t do any mods that look like a “ricer” many are doing these days. Blacked out grill and wheels is two of the best mods you can do on the 10th gen accords. Are you going to black out the window trims too? What’s your opinion on putting touring taillights on a sport ?
Aww. Thanks man. I appreciate that. You definitely should. It’s a great community and you get a lot of help with mods and just maintaining your car that definitely helps a long the way. I’ve gotten so much advice through the years that really help.
Honda Jon just one more thing, those lights will fit on my 2018 accord right? I was reading the reviews and I saw that a lot of people complained about it being bad but it looks so nice when you installed them
Yeah. They fit. I love them. One went out after about 8 months but they replaced them free Of charge. That’s pretty good. Most bulbs with built in resistors will go out quicker than your standard led bulbs.
I just emailed them and said that one bulb started hyper flashing. They sent me a replacement and even mailed a return label so you can send the old one back so they can see what went wrong. 👍🏻
What's up man. Good videos. I got a question. Do you have a video of how to replace the inside rear stop light. Or can you do one. Hope you can reply back. Thanks
Hey there. I am. One went out after almost a year but the company sent me a replacement free of charge. Definitely a great bulb and looks nice. I hear that most bulbs with resistors built in don’t last as long as a conventional led bulbs. But they have a lifetime guarantee so you having nothing to lose.
Yeah. It’s weird but it’s deep red and matched the rest of the brake lights absolutely no hyper flashing. Can’t say enough about this bulbs. They are great 👍🏻
Those are a pain. It takes a couple tries but eventually they’ll go in. I found the best way is to put them on the light side first then work on snapping them in on the other side.
Jon, I am thinking about installing the LED's you reported on this video. Are they still working for you well? Do you still recommend them? Are they truly plug and play? Let me know. Keep up the good work on your content and videos. Thanks and have a great day!
Thanks man. They do work well. I did have to get another one because one started hyper flashing. I have found that to be the case with any plug and play bulb. They won’t last as long since they have the built in resistor which runs hotter. The bulbs with an external resistor should last longer but are a little harder to install.
Amazon does that sometimes. If you used the link they will fit. I’ve noticed a lot amazon will say things don’t fit when in fact they do. Don’t worry if you clicked through the link 👍🏻
Hi Jon, I am looking for led bulbs for the front my 2018 Pilot Elite. I got Lasfit red for the back with the integrated load resistor, but none work for the amber front ones. Any ideas, as I don’t want to modify my Pilot’s wiring.
Hey Honda Jon, was looking around for lights and stumbled upon your video. Everything was super helpful and I ended up purchasing the lights you had here as you said it didn’t require any resistors or anything. However, from reading all kinds of comments on the LED lights that I found from different manufacturers they all had one similar issue (even when they were CANBUS and said they had built in resistors and such) and that issue was that after 5-30 minutes depending on the bulb they would begin to hyperflash either from a malfunction or it overheating. Is there anyway you could test this such as leaving them on in your garage with your hazards running for around 30 minutes to see if they do it? If you’re able to that would be super helpful to hear your findings, or maybe if you want even make a video to show it so I might be able to reference it in my review on Amazon stating that it works for the 2018 Accords and 2019 since amazon doesn’t believe it will fit. If you’re too busy, no worries I did order them from your direct link and will be installing them in a day or two after they arrive and can test then. Just figured since you had them in already it might save me pulling the light out to find it also had a similar issue that the other companies lights had. Thanks!
What’s up man? Thanks for watching. I’ll definitely do that. I have heard that every bulb will do that but would anyone rarely use there turn signals for that long. I’ve heard the ones I have will do it after ten minutes. If you need to use your flashers they more than likely will do it. No damage or anything. It’s just your system telling you a bulb is out because it thinks there is. Once you turn them off they will resume there normal operation. I will do a quick video showing that. I appreciate you watching. If you haven’t please subscribe. I have new content weekly 👊🏼
Honda Jon Hey! Thanks for posting your video! I understand. The chance of needing to use it more than 10 or so minutes isn’t critical, though I do live in a city and sometimes have to park with them on. I was just curious since I wasn’t able to find anything about these bulbs having that problem. Also, in the video would it be possible for you to setup a way either through sped up video or something that would give us roughly the time they would start hyper-flashing if they do within the 30 minutes kind of like a science experiment? Also, you mentioned that if they started hyper-flashing if you shut them off and turn them back on it goes away. Did you mean that it would immediately upon turning it back on after it was on for so long that they wouldn’t hyper-flash? Thanks again for a quick response!
@@HondaJon Thanks for the quick response. When I click on the link you posted it looks like the design of the bulb has changed a little bit. They no longer have LEDs on the end, only around the perimeter.
Another nice video Jon thanks for walking us through.I wanted to know how to remove those tail lights it looks a little challenging removing them you can't be too rough.Does the overlays help not been way to bright?
Thanks man. It’s not hard. You can do it. You just have to wiggle the light and the front tabs will “pop” out. Just don’t force anything. Yeah the overlay helps dim it a little. It’s still bright but I like it. Tomorrow I will upload a video at night showing them from a distance. If your thinking about a nice set I recommend these for sure. 👍🏻
They are great. No issues. They are holding up perfectly. I might take them off and run the oem ones. It’s a hard decision lol. Sometimes I like the matte and sometimes I like the glossy. Either way they are great. The best vinyl and the install can’t be easier 👍🏻
Yeah just the ones it comes with. They have glossy pillars. I wouldn’t say scratch resistant. They actually scratch easy. That’s why a lot of people are putting films on them. You can polish them which helps but they will eventually get scratched up
@@HondaJon I greatly appreciate ur quick response. I will order the bulbs. Keep the videos coming. I enjoy learning from ur channel. Also did u know it is possible to watch Netflix etc. With our Accord X?
It’s not a Phillips screw. So you shouldn’t use Phillips screw driver. They are JS Japanese head screws. Every bolt on that car is a Japanese staple screw. American tools tend to strip these because that aren’t the same exact size.
Don’t listen to that. If it’s what I listed it will. Amazon doesn’t know all the specs. They work perfectly. I’ve had them for a long time Now. No issues. 👍🏻
I have a white Accord, would like to do that. You had to remove the emblems and lettering or you did it on the car? The lettering looks like it could be a pain, trying to line it up when you put them back on.
No you leave it on the car. It’s actually easy. You leave about an inch around the entire emblem then mask off. Spray about 7 light coats. Once down you simply peel it off the car and it snaps where the emblem meets the car. It’s pretty neat how it works
Hi Jon, Great vid. From your recent videos I know you don’t own this car (I believe anymore) but maybe you could help me on this question. 🥲 I have a 2018 ACCORD and I live in a hot climate state… online I see most reviews for LED bulbs with built in resistors hyper flash when their is excessive heat by either temp outside, or by duration of the bulb on (hot temp). Did you encounter hyperflash when leaving bulbs on for a long period of time? Did it hyper flash if indeed your area was hot? I’m considering switching my stock to these but I’d love to know your honest review. Thanks buddy!
Thanks bro. I have heard that. I’m never ran into that but you could use an inline resistor and that should eliminate the issue. Let me know if that helps.
@@HondaJon that’s good to know then. I’m thinking of just trying it out with the bulbs and seeing how it goes from there. Did you by chance live in a hot state?
I would. I don’t think you’ll have issues unless you leave them On for 5 or more minutes. Where I live it gets in the 90-100’s in the summer and didn’t have issues.
I have them But haven’t installed them in my new car yet. One went out but they replaced it free of charge. I have heard a lot of the led turn signal bulbs don’t last all thy long.
On my daily car I got the Sylvania Zevo LED brake light and turn signal (3157R) yes they are both red and they are super bright, anyways I was going to say that they have been working fine for over a year, and I have a brake led strobe module on the brake lights and have not had any problems. I would buy these lights for my Accord too, but Like you mentioned in the video, I don’t want to splice the wires neither to connect the resistor for the turn signals. That’s why I’m looking for something that is plug and play.
Hey man i want to get my hands on this and i tapped on the link in your bio and it took me to Amazon . In amazon it asked me to put my vehicle year make and brand , and it says it wont fit on a 2019 accord . Do i just go ahead and order it or ?
I was the same. I’m 100% happy with these. No issues at all. I love them. They are bright but it definitely gets the attention of people behind you which is a good thing.
I bought these LED bulbs about 9 months ago. So far no problems, but they're TOO bright. One of these days I expect to be pulled over by a cop and given a ticket. I don't leave my blinkers going at signal lights because I just know I am blinding the guy behind me.
I bought these on May 20th, 2020 and after about 1 year they stopped working. The left one had LEDs burn out and then the right one a few weeks later. I would NOT recommend these. The seller (Off Amazon) told me too bad.
Most of the bulbs with built in resistors do not last that long. Alla lighting has a great warranty. You simply need to contact them and they’ll help you out. I did and was provided replacement bulbs.
@@HondaJon I contacted them told them the bulbs went out after only about 14 months. They said there was nothing they could do since they only have a 12 month warranty.
Installed mine. Was ready for a battle with the rear lights. They popped off so easy lol. Thanks for the vid.
Lol. It’s tricky at first for sure.
I just used this video to change out my 2018 Accord Rear Turn indicators in under 20mins. Thanks
Anytime bro. 👍🏻
I've always been afraid of popping things out and removing screws and stuff. I rather just pay a professional to do it for me.. Yeah I know I'll save $$$ the way I see it is since I'm very impatient and liable to break something, I'll end up paying more when I have to buy the replacement part.. Looks nice. I might give it a try on my '19 1.5. Seems easy enough I guess.. Wish me luck.
I agree. Sometimes it’s better than breaking something. I highly recommend these bulbs. They are amazing and light up the night 👊🏼
Maybe instead of having a defeatist attitude you can learn and practice using a screwdriver and changing a lightbulb lol it’s not that hard, have some confidence and don’t rush yourself.
I would like to see how you do the front one
thank you so much, jon for this and all your vids. sincerely appreciate how you anticipate the problems we may face and your walkthroughs are easily the most diligent and easy to comprehend. oh, 8mm socket works perfectly to get the screws out as well👍
Thanks so much bro. That truly means a lot to me. 👊🏼
Thank you Jon ... I ordered these from Amazon ... these were like $15.00 more than most others on eBay but you advised there is a lifetime guarantee . The other brand led turn signal I bought previously , lasted a year and half and they only offer 6 month warranty . So I figured these have a better warranty ... you mentioned life time and I order these from ALLA ... I was checking on the order and read their website .. they list 1 year warranty... but I trust Honda Jon ... and you’ve had a good experience with these from ALLA .
I hope I do too
Thanks man. You will. They stand behind their products that’s the best part.
Why did Honda redesign such a lame way of changing out the bulb? i own a 2002 and 2016 Accord and all i have to do is pull back the rear trunk liner where the rear tail light housing sits and vola, it's there and easy to get at. btw i had to change out the rear flasher on my 2016 Sport also because the original were way too faint. The replacement rear flashers were fantastic, extremely bright.
iJDMTOY (2) No Resistor, No Hyper Flash 21W High Power Amber 7440 W21W T20 LED Bulbs For Car Front or Rear Turn Signal Lights .
confused...is it really that lame? it is two screws and you are in...
Are you still running these? Normally aftermarket LED turn signals are extremely bright and could easily blind people behind you - prior ones I have tried seem dangerous to use because they are simply too bright. I wish there was a standard brightness LED light. I don't need the "headlight" brightness, just instant on/off.
can you give me a link for some white ones? also is there any more help on installing that nightmare trim peice?
Not sure if they make white ones but you can find them on Amazon. The trim is not hard just tricky. Keep trying on one side as you push the trim part against the light. Eventually you’ll get it to snap in. It’s the weirdest design.
I wonder why on Amazon it says it doesn’t fit 2019 Accord?
For some reason your link to the Amazon website says these don't fit my 2019 Accord... Any suggestions?
As long as it’s the one in the video it will 👍🏻
@@HondaJon Awesome! Thanks man! Great video by the way, keep up the good work.
Thanks so much bro 😎
Just ordered these on Amazon. Thanks for the content!
No problem man. You’ll love them. 👍🏻👊🏼
Are there white or red ones I want to change mine to led but I want either red or white
Yes. You can get them
In any color really.
Does the 1.5t have auto lock where you walk away with the fob and it automatically locks it for you?
It doesn’t. That’s one thing the 2.0 added that’s definitely worth it
@@HondaJon I heard it was on the 1.5 from a few ppl
Only if it’s ex and above
@@HondaJon hm idk I got told by a few ppl that they have it on their 1.5s
Hey bro, where did you get that red transparent sheet for turn signal?
Check out delicious stickers ca on eBay. They have all the overlays for the Honda Accord.
@@HondaJon got it, thank you so much 🙏🏽
Anytime bro 😎
I like your accord. You didn’t do any mods that look like a “ricer” many are doing these days. Blacked out grill and wheels is two of the best mods you can do on the 10th gen accords. Are you going to black out the window trims too? What’s your opinion on putting touring taillights on a sport ?
Jon you are angel did you know that!
Thank you so much dude🙏
Great. Thanks so much 👍🏻
Nice video as usual Jon.
Thanks man. 👊🏼
They are crazy bright but work great with 20% tinted covers
I agree. I have 35% tint and they are still really bright. They definitely get people’s attention. I love them.
Where did you get the blacked out emblem and letters? Looked through your other videos. Couldn’t find it. Thanks.
I didn’t do a video but I plastidipped them. I highly recommend it. They look awesome and it’s inexpensive
I just installed mine and I love them! Thanks
Awesome. Me too. You’ll definitely be noticed. Which is a nice safety feature.
Man love the videos so many things I’m doing to my accord cause of you
Aww. Thanks man. I appreciate that. You definitely should. It’s a great community and you get a lot of help with mods and just maintaining your car that definitely helps a long the way. I’ve gotten so much advice through the years that really help.
Honda Jon just one more thing, those lights will fit on my 2018 accord right? I was reading the reviews and I saw that a lot of people complained about it being bad but it looks so nice when you installed them
Yeah. They fit. I love them. One went out after about 8 months but they replaced them free
Of charge. That’s pretty good. Most bulbs with built in resistors will go out quicker than your standard led bulbs.
Honda Jon what did you tell them just for the future in case It were ever to happen.
I just emailed them and said that one bulb started hyper flashing. They sent me a replacement and even mailed a return label so you can send the old one back so they can see what went wrong. 👍🏻
What's up man. Good videos. I got a question. Do you have a video of how to replace the inside rear stop light. Or can you do one. Hope you can reply back. Thanks
Thanks man. It’s easy. There are tabs inside the trunk that hold it in place. If you look up under the rear deck you’ll see the contact points.
I can’t see the link of the bulbs to purchase. Must be the lame you tube iOS app. Can you post the purchase link again?
Try this link. Let me know if it works for you.
www.amazon.com/dp/B07GVT4F2C/ref=cm_sw_r_cp_awdb_t1_oIykFb6VE0KSE
Hi Jon...2018 accord touring ...are you still having good luck with these LED for the rear turn signals ?
Hey there. I am. One went out after almost a year but the company sent me a replacement free of charge. Definitely a great bulb and looks nice. I hear that most bulbs with resistors built in don’t last as long as a conventional led bulbs. But they have a lifetime guarantee so you having nothing to lose.
Thanks Jon
Anytime bro.
Since your using the amber ones Is it really red behind the overlay? And no hyper flash at all?
Yeah. It’s weird but it’s deep red and matched the rest of the brake lights absolutely no hyper flashing. Can’t say enough about this bulbs. They are great 👍🏻
is there a link for the ones you said were too bright?
Honestly I do not remember exactly which ones they were. My latest ones I reviewed are still extremely bright. I highly recommend those.
I need help putting the damn plastic cover back on 😪😪😪
Those are a pain. It takes a couple tries but eventually they’ll go in. I found the best way is to put them on the light side first then work on snapping them in on the other side.
@@HondaJon i figured it out thanks 😌
I actually work at Honda but my plant builds the CRV, MDX and RDX
👊🏼
Thank you for sharing your experience and tips!
Anytime brother. It’s great to help eachother out. 👊🏼
How do I change my front right indicater
It’s a sealed unit I believe
@@HondaJon thank you
Anytime
Thanks for taking the time to share this info.
Thank you
Jon, I am thinking about installing the LED's you reported on this video. Are they still working for you well? Do you still recommend them? Are they truly plug and play? Let me know. Keep up the good work on your content and videos. Thanks and have a great day!
Thanks man. They do work well. I did have to get another one because one started hyper flashing. I have found that to be the case with any plug and play bulb. They won’t last as long since they have the built in resistor which runs hotter. The bulbs with an external resistor should last longer but are a little harder to install.
@@HondaJon thanks for the quick response. I am going to go ahead with ordering and installing the bulbs. Have a wonderful day Jon!!
No problem. Yeah I love them. They are bright.
Do you know if these come in red?
Why does amazon say this product does not fit your car for the Honda accord 2018?
Amazon does that sometimes. If you used the link they will fit. I’ve noticed a lot amazon will say things don’t fit when in fact they do. Don’t worry if you clicked through the link 👍🏻
@@HondaJon thank you! Just to make sure it's the 7507 for size?
No problem. Yeah. The 7507 is the correct one. 👍🏻
Hi Jon, I am looking for led bulbs for the front my 2018 Pilot Elite. I got Lasfit red for the back with the integrated load resistor, but none work for the amber front ones. Any ideas, as I don’t want to modify my Pilot’s wiring.
Do you know what the bulb number is? I thought they were led already?
@@HondaJon Front turn signal-7444NA (Natural Amber) Rear turn signal-7440. Yes, I have factory rear led brake and tail lights already.
Do you know if the pilot had led turn signals in the front stock? I thought they did
They are incandescent front and back from factory.
Thanks man for that info.
My lights start flashing fast I don’t know if I should buy the same or another brand
Bought these! Installed them Friday and they are SUPER bright. Definitely going to tint my lights. Other than that I like them
👍🏻
Noob question are front n rear bulbs identical
I believe fronts is a sealed led unit so it can’t be swapped.
@@HondaJon thank you
Can you used the same ones in the front too
No. The front are already led.
@@HondaJon thank very much for your help God bless you
Anytime man. Thank you.
I installed the rear led turn signal but mine is flikering fast. Why is that
Does it have a built in resistor? That’s the sign that it doesn’t or is faulty because it’s not regulating the voltage
Can you post a link for High beams LED that you bought?
No problem. It should be in this video I did of them. ruclips.net/video/EpRXLXxaqfk/видео.html
Roger that! Thanks
can I buy the white version of these lights to use as the reverse lights?
They are different bulbs. Check out philips 921 white led. Extremely bright and great build quality. I have them and they are perfect.
@@HondaJon can I get an amazon link?
I bought them from eBay. Just type in philips 921 white led. You’ll see a lot. They aren’t too expensive either.
Hey Honda Jon, was looking around for lights and stumbled upon your video. Everything was super helpful and I ended up purchasing the lights you had here as you said it didn’t require any resistors or anything. However, from reading all kinds of comments on the LED lights that I found from different manufacturers they all had one similar issue (even when they were CANBUS and said they had built in resistors and such) and that issue was that after 5-30 minutes depending on the bulb they would begin to hyperflash either from a malfunction or it overheating. Is there anyway you could test this such as leaving them on in your garage with your hazards running for around 30 minutes to see if they do it? If you’re able to that would be super helpful to hear your findings, or maybe if you want even make a video to show it so I might be able to reference it in my review on Amazon stating that it works for the 2018 Accords and 2019 since amazon doesn’t believe it will fit. If you’re too busy, no worries I did order them from your direct link and will be installing them in a day or two after they arrive and can test then. Just figured since you had them in already it might save me pulling the light out to find it also had a similar issue that the other companies lights had. Thanks!
What’s up man? Thanks for watching. I’ll definitely do that. I have heard that every bulb will do that but would anyone rarely use there turn signals for that long. I’ve heard the ones I have will do it after ten minutes. If you need to use your flashers they more than likely will do it. No damage or anything. It’s just your system telling you a bulb is out because it thinks there is. Once you turn them off they will resume there normal operation. I will do a quick video showing that. I appreciate you watching. If you haven’t please subscribe. I have new content weekly 👊🏼
Honda Jon Hey! Thanks for posting your video! I understand. The chance of needing to use it more than 10 or so minutes isn’t critical, though I do live in a city and sometimes have to park with them on. I was just curious since I wasn’t able to find anything about these bulbs having that problem. Also, in the video would it be possible for you to setup a way either through sped up video or something that would give us roughly the time they would start hyper-flashing if they do within the 30 minutes kind of like a science experiment? Also, you mentioned that if they started hyper-flashing if you shut them off and turn them back on it goes away. Did you mean that it would immediately upon turning it back on after it was on for so long that they wouldn’t hyper-flash? Thanks again for a quick response!
No problem. I’ll definitely check it all out and post a video explaining everything. 👊🏼
Honda Jon Hey, hows the video coming?
Hey man. It’s good. I’ll post it in a couple weeks. I like to space my videos and mix them up a little bit. I’ll definitely get it posted though. 👊🏼
Have you had any issues with the bulbs since this video was made?
Not at all. They are perfect and amazing build quality
@@HondaJon Thanks for the quick response. When I click on the link you posted it looks like the design of the bulb has changed a little bit. They no longer have LEDs on the end, only around the perimeter.
Another nice video Jon thanks for walking us through.I wanted to know how to remove those tail lights it looks a little challenging removing them you can't be too rough.Does the overlays help not been way to bright?
Thanks man. It’s not hard. You can do it. You just have to wiggle the light and the front tabs will “pop” out. Just don’t force anything. Yeah the overlay helps dim it a little. It’s still bright but I like it. Tomorrow I will upload a video at night showing them from a distance. If your thinking about a nice set I recommend these for sure. 👍🏻
@@HondaJon
Jon how are those matte door pillar overlays are they holding are they good quality?
They are great. No issues. They are holding up perfectly. I might take them off and run the oem ones. It’s a hard decision lol. Sometimes I like the matte and sometimes I like the glossy. Either way they are great. The best vinyl and the install can’t be easier 👍🏻
@@HondaJon The OEM you want are glossy ? Are they scratch resistance?
Yeah just the ones it comes with. They have glossy pillars. I wouldn’t say scratch resistant. They actually scratch easy. That’s why a lot of people are putting films on them. You can polish them which helps but they will eventually get scratched up
Do they fit '21 2.0t touring?
They should all be the same if they are incandescent bulbs
@@HondaJon thanks! Amazon says it doesn't fit for some reason...
A lot of the time it does say that. Make sure it’s the same bulb number.
I got the same ones it’s just like a sun ☀️ light too bright
I checked the link you provided. I have a 2018 honda accord touring 2.0t. On Amazon it's saying the bulbs won't fit my vehicle. Any advice?
As long as they are the item I have in the listing they will fit. Sometimes amazon is wrong with what fits what vehicles.
@@HondaJon I greatly appreciate ur quick response. I will order the bulbs. Keep the videos coming. I enjoy learning from ur channel. Also did u know it is possible to watch Netflix etc. With our Accord X?
Thanks bro. I appreciate that. Yeah if you jailbreak your phone I know you can. Awesome hack for sure.
It’s not a Phillips screw. So you shouldn’t use Phillips screw driver. They are JS Japanese head screws. Every bolt on that car is a Japanese staple screw. American tools tend to strip these because that aren’t the same exact size.
First thing it says on Amazon "this product does not fit your 2019 Honda Accord" 😔
Don’t listen to that. If it’s what I listed it will. Amazon doesn’t know all the specs. They work perfectly. I’ve had them for a long time
Now. No issues. 👍🏻
@@HondaJon hello do you know if they come in red so I dont have to put a lense on the turn signal like you have
I’m
Sure they do. Not positive but they should have red leds
Did you Plasti the rear emblem and lettering?
Yeah. It’s easy and in my opinion looks amazing.
I have a white Accord, would like to do that. You had to remove the emblems and lettering or you did it on the car? The lettering looks like it could be a pain, trying to line it up when you put them back on.
No you leave it on the car. It’s actually easy. You leave about an inch around the entire emblem then mask off. Spray about 7 light coats. Once down you simply peel it off the car and it snaps where the emblem meets the car. It’s pretty neat how it works
Honda Jon you the man! Thanks!
No problem man. Feel free to let me know if you have any questions. It will great on a white accord 👋
Hi Jon,
Great vid. From your recent videos I know you don’t own this car (I believe anymore) but maybe you could help me on this question. 🥲 I have a 2018 ACCORD and I live in a hot climate state… online I see most reviews for LED bulbs with built in resistors hyper flash when their is excessive heat by either temp outside, or by duration of the bulb on (hot temp). Did you encounter hyperflash when leaving bulbs on for a long period of time? Did it hyper flash if indeed your area was hot?
I’m considering switching my stock to these but I’d love to know your honest review.
Thanks buddy!
Thanks bro. I have heard that. I’m never ran into that but you could use an inline resistor and that should eliminate the issue. Let me know if that helps.
@@HondaJon that’s good to know then. I’m thinking of just trying it out with the bulbs and seeing how it goes from there. Did you by chance live in a hot state?
I would. I don’t think you’ll have issues unless you leave them
On for 5 or more minutes. Where I live it gets in the 90-100’s in the summer and didn’t have issues.
@@HondaJon thank you very much for your feedback!
Anytime bro 👊🏼
Hey Jon, where can I get the overlay ?
Check out delicioustickerca. They have all the overlays you need.
Thanks once again for this video imma order these Friday , we have the same color sport 💯🙌🏾
Nice. You will really love these
Nice vid. What color did you get? White or yellow? Any cons you think of getting the red ones?
Nevermind I see the white and red ones aren't compatible with the 18 Accord.
They are awesome. Nice deep red color and more noticeable in full sun. 👍🏻
These LED's got the worst rating on Amazon.
Number one complaint they don't last.
Hi Jon, just wondering if this will fit the 2019 accord. Amazon keeps saying it won't fit. Thanks.
Hi. If it’s the ones in my listing they fit perfect. You can’t always trust eBay or amazon 👍🏻
@@HondaJon alright! Just ordered them. Thanks!
Nice. You will love them. They are nice and bright and definitely will be noticed. The best part is it’s plug and play.
@@HondaJon I just want to be for sure, these are headlights not high beams correct? But it is bright enough to use it as one?
No. These are the rear turn signal bulbs.
@Honda Jon, do you still have the same lights? Have you had any problems with them? On Amazon they have a few bad reviews.
I have them
But haven’t installed them in my new car yet. One went out but they replaced it free of charge. I have heard a lot of the led turn signal bulbs don’t last all thy long.
On my daily car I got the Sylvania Zevo LED brake light and turn signal (3157R) yes they are both red and they are super bright, anyways I was going to say that they have been working fine for over a year, and I have a brake led strobe module on the brake lights and have not had any problems. I would buy these lights for my Accord too, but Like you mentioned in the video, I don’t want to splice the wires neither to connect the resistor for the turn signals. That’s why I’m looking for something that is plug and play.
What did you use for the head lights, yes am a newbie!
Nice. The film or bulbs?
@@HondaJon BulbS LED?
Here’s the video for the high beams
ruclips.net/video/EpRXLXxaqfk/видео.html
Do you need resistors to prevent hyperflashing?
No. They are built in. I’ve been using them for almost a year. No issues. I love them.
@@HondaJon thanks!
Anytime bro. 👍🏻
Hey man i want to get my hands on this and i tapped on the link in your bio and it took me to Amazon . In amazon it asked me to put my vehicle year make and brand , and it says it wont fit on a 2019 accord . Do i just go ahead and order it or ?
Yeah. It is never correct. If it’s through my link it will fit. I love them 👍🏻
Honda Jon great man thank you ! Im having all of my mods ready . Im getting one in 2 weeks! Im excited Lol .
Hi Jon can I have the link on where to buy the led bulb..thanks bro
No problem man. It’s in the description in this video 👍🏻
Does it fit with 2019 Accord hybrid ?
It should as long as it used the same bulb which I’m almost sure it does
Yes, it does. Its the same car with same bulbs.
How's this holding up? Any hyper-flashing? Is it too bright? I can't decide which turn signal LED to get.
I was the same. I’m 100% happy with these. No issues at all. I love them. They are bright but it definitely gets the attention of people behind you which is a good thing.
Bro are these bulbs in the rear signals legal?
Yeah they are. There’s no law against how bright a turn signal needs to be. I’m fact these are more noticeable so it gets people’s attention better.
Does it hyper flash if you leave it for at least 10mins? (Turn signal)
Hello. I don’t think so but I have never left them on for that long. They work perfect
Does it affect the headlight making it weak or something else?
Not at all. Led bulbs need resistors or they will flash too fast.
Does hyper flash when u turn on one side?
No. They work perfectly. 👍🏻
I bought these LED bulbs about 9 months ago. So far no problems, but they're TOO bright. One of these days I expect to be pulled over by a cop and given a ticket. I don't leave my blinkers going at signal lights because I just know I am blinding the guy behind me.
I agree. They are really bright and I thought the same thing. I highly recommend a smoke tint over to dim then a bit 😝
I bought these on May 20th, 2020 and after about 1 year they stopped working. The left one had LEDs burn out and then the right one a few weeks later. I would NOT recommend these. The seller (Off Amazon) told me too bad.
Most of the bulbs with built in resistors do not last that long. Alla lighting has a great warranty. You simply need to contact them and they’ll help you out. I did and was provided replacement bulbs.
@@HondaJon I contacted them told them the bulbs went out after only about 14 months. They said there was nothing they could do since they only have a 12 month warranty.
Sorry to hear that. Let me know how long these ones last because from my experience they don’t last too long if using a built in resistor.
Just looked up the first link
And put in 2018 Accord...
Do not fit.......
It does. If it’s the link I provided it’s the right one. You can always trust the listings.
Might start my own RUclips
I HATE that stupid black plastic trim piece :)
Me too. It’s the most awkward piece to put back on. Why couldn’t it just pop into place easy lol
I break it almost everytime I take it off, super glue it back
Is the brake light and reverse light LEDs? I'm looking to replace all non LED bulbs
The reverse I replaced are led. The brake lights I also replaced with red led philips bulbs.
@@HondaJon Did you make a video on the brake lights? I can't find one