I am Audison Forza C8.14 User. Thanks for the video, it's very nice. But where can I find reference curves? Can you share it with me, please? And what are the differences between these reference lines? On what basis should we choose?
Hello, when you install bitDrive software, you will automatically have our 3 proposed curves installed in your laptop: HAC-J, HAC-R and HAC-U. They appear when you open the Acoustic RTA tool and press on Load from reference file. The choice of the reference curve depends on your personal taste. "J" stands for Jazz, "R" stands for Rock, "U" stands for Universal. We suggest to try and listen to find what fits better your taste. -Best reagard
Very nice detail. Im going to look in my apf8.9bit sw & see if there is a similar target curve. ( if not, at least its in the new sw, with new forza amps👍🏼👏🏼😀)
The bit Drive software with the Acoustic RTA and the Reference Curve is not compatible with the AP F 8.9. For tuning that amplifier, dealers often use the bit Tune standalone acoustic RTA system, which has reference curves in it.
So far in 2 audison amplifiers I have seen that input equalizer is not working. I tjust shows blank for all signals. Auto tuning also fails. Do you guys know a solution to this? Audison's support is not helpful in this regard.
Hello, you can set the AF Master volume at around -15 or -10 dB, so that after aligning the cabin acoustic response to the target curve you will still have room to increase your volume as much as you want! The entire measure with microphone must be done with all closed doors and the operator standing out of the car, in order to replicate the common listening case. Best regards
I am Audison Forza C8.14 User. Thanks for the video, it's very nice. But where can I find reference curves? Can you share it with me, please? And what are the differences between these reference lines? On what basis should we choose?
Hello, when you install bitDrive software, you will automatically have our 3 proposed curves installed in your laptop: HAC-J, HAC-R and HAC-U. They appear when you open the Acoustic RTA tool and press on Load from reference file. The choice of the reference curve depends on your personal taste. "J" stands for Jazz, "R" stands for Rock, "U" stands for Universal.
We suggest to try and listen to find what fits better your taste. -Best reagard
same here
@@AudisonItofficial so the HAC-E curves are not for normal using?
@@AudisonItofficial Thanks a lot. :)
@@Firestarter2222 HAC-E is an alternative curve that some users find very pleasant. You can use if tou like ;) -Regards
What track must be played during audio analyzer / microphone setup? Or is it MONO PINK NOISE on every step...
I don't see any E curve file when I pick reference curve. I have latest software. AF C8.14 bit
Very nice detail. Im going to look in my apf8.9bit sw & see if there is a similar target curve. ( if not, at least its in the new sw, with new forza amps👍🏼👏🏼😀)
The bit Drive software with the Acoustic RTA and the Reference Curve is not compatible with the AP F 8.9. For tuning that amplifier, dealers often use the bit Tune standalone acoustic RTA system, which has reference curves in it.
So far in 2 audison amplifiers I have seen that input equalizer is not working. I tjust shows blank for all signals. Auto tuning also fails. Do you guys know a solution to this? Audison's support is not helpful in this regard.
Merhaba dayton imm-6 kalibre dosyasını nasıl ekleyebilirim yardımcı olur musun?
If using minidsp umik-1, how to calibrate the mic with audison bit tune software?
what if you have a center channel?
hello how do i add dayton imm-6 caliber file
How loud do i play the pink noisee and is it not measured with closed door?
Hello, you can set the AF Master volume at around -15 or -10 dB, so that after aligning the cabin acoustic response to the target curve you will still have room to increase your volume as much as you want! The entire measure with microphone must be done with all closed doors and the operator standing out of the car, in order to replicate the common listening case. Best regards
@@AudisonItofficial In bitDrive software, how to load calibration file for calibrated microphone e.g. UMIK-1?
poderia disponibilizar o arquivo salvo para eu testar no meu sistema
Olá, esta configuração é apenas um exemplo, não pode ser utilizada para outros sistemas. -Cumprimentos
👍
promo sm