Great video everything proven people like myself are buying VCR players cleaning tapes vhs movies VCR belts offline from there phone now days everything proven
Hello Aleksandr! Firstly, thank you for sharing your video. I disassembled a VHS Player and inside it there is a Capstan Motor that has a "Panasonic AN3844SB" Controller IC, but I can't find its Datasheet on the internet. This IC has 28 pins. Is there any way to test the pins for power? Thanks
hi, your video was the only one that explains the connection of the engine ,will be that can mount an image to intender better because still this difficult of understand.until
I have a "U-26B engine Capstan SONY" and I need to operate the Hall sensor, how you could get the information for the connection? It uses a chip "cxa8005"
+Aleksandr Sandovic Cor 10 months! I did get another motor to work, theres was something odd about the ic, I think it needed a 2 phase clock or something difficult like that.
Thanks for your video. I have a Capstan motor JVC that is here: www.ksp-electronics.com/en/product/view/25473-cap-motor-qar0087-005 the connector looks almost exactly as yours. BUT I can't figure out how the pins needs to be used. If you look at the above https:... and the connector is at the bottom right side, the motor is at the top the connector has 8 wires. let's call the left side 4 connectors 1,2,3,4 and the right side would be 5,6,7,8. The 1, 2 and 3 has no label. 3 = SV or 5V (hard to tell) and under 5V is CTL label, the right side : 5 = 12V, 6 = NC, 7 = F/R, 8 = P - G. What wires goes to 12V - is it 5 + 8 - right? When I put 12V on 12V at #5 =12V+ and on #8 goes GROUND nothing happens. When I put the +5V on #3 my adjustable power supply takes 2.5A and the voltage dropped to 4.8V and the motor moves a small amount and STOPS! I don't understand this at all, if you can help I'll try your suggestion. Thank you!
Great video everything proven people like myself are buying VCR players cleaning tapes vhs movies VCR belts offline from there phone now days everything proven
I appreciate that you SHOW HOW TO GET THE MOROR WORKING - instead of just the tear down!!
You should do more videos like this
ssßss
Thanks for information Aleksandr. Good video.
Very informative. Thanks for sharing.
Good job and good use of a computer power supply
I'mma use it to rewind vcr/vhs tapes.
I'll pay for the detail of conections for that capstan M56730ASP.
На бересте писал, что ли :))
DEPOSITO NA CONTA DE QUEM INFORMAR O ESQUEMA COM CLAREZA
Hello Aleksandr! Firstly, thank you for sharing your video.
I disassembled a VHS Player and inside it there is a Capstan Motor that has a "Panasonic AN3844SB" Controller IC, but I can't find its Datasheet on the internet. This IC has 28 pins. Is there any way to test the pins for power? Thanks
try finding manuals at elektrotanya
I didn't find it either.@@ivok9846
i should’ve done that instead of removing the pcb and connecting UVWC
Can u provide me ur videos of run capston motor?
Лучше бы написал выводы микросхемы и её название.
название есть на микросхеме а вот что сколько и куда питать не ясно
do you know how to remove that retaining nut on the capstan rotor (where the pulley is) to separate the rotor from the stator?
hi, your video was the only one that explains the connection of the engine ,will be that can mount an image to intender better because still this difficult of understand.until
Gnd | 5v | ? | 5v
Gnd | ? | 12v | reverse 5v
Do you have a m63101fp chip on your board? What is the pinout on that connector/header?
I have a "U-26B engine Capstan SONY" and I need to operate the Hall sensor, how you could get the information for the connection?
It uses a chip "cxa8005"
Cientifico loco,cientific crazy
how can I replicate this at home? is there a cleaner schematic ?
Gnd | 5v | ? | 5v
Gnd | ? | 12v | reverse 5v
make it Washing machine direct drive
You have to speak.
Do you know how to make vcr head motor generate electricity ? nobody knows. thoughts ?
You need to isolate the coils from the circuit board
Best method: take the coil and rotor assembly off of the circuit board
Como é que posso fazer uma ligação em um desses?
Hi, I tried this but it doesnt work for my motor, it looks the same, but maybe the chip is diffrent
you need to find a datasheet
+Aleksandr Sandovic Cor 10 months!
I did get another motor to work, theres was something odd about the ic, I think it needed a 2 phase clock or something difficult like that.
sorry for 10 month delay ^^' i have time consuming work.
can you eventually read the text on the chip and what model vhs it is from ?
I need 8432 ic can you please parcel me
Hi my connector has 8 legs, do you know how that can be powered? Thank you.
Have you find your answer? Please see my comment asking him ... and let me know also. Thanks!
Hi, my conector have 7 legs. how to power it?
where did you find this motor?
Vhs player all of rhem have some kind of capstan motor
@@xeofreestyle20whats ur email
Thanks for your video. I have a Capstan motor JVC that is here: www.ksp-electronics.com/en/product/view/25473-cap-motor-qar0087-005 the connector looks almost exactly as yours. BUT I can't figure out how the pins needs to be used. If you look at the above https:... and the connector is at the bottom right side, the motor is at the top the connector has 8 wires. let's call the left side 4 connectors 1,2,3,4 and the right side would be 5,6,7,8. The 1, 2 and 3 has no label. 3 = SV or 5V (hard to tell) and under 5V is CTL label, the right side : 5 = 12V, 6 = NC, 7 = F/R, 8 = P - G. What wires goes to 12V - is it 5 + 8 - right? When I put 12V on 12V at #5 =12V+ and on #8 goes GROUND nothing happens. When I put the +5V on #3 my adjustable power supply takes 2.5A and the voltage dropped to 4.8V and the motor moves a small amount and STOPS! I don't understand this at all, if you can help I'll try your suggestion. Thank you!
Have u find because i have same happened motor just spin haft
Tenho três motores e três cabeçotes para vender !!
plz could anyone explain this to me i need help
MEJOR QUITA TU PROMOCIONAL
it is something youtube did automatically