Tutorial - Install your Pumptrol Pressure Switch - Square D sensors rebrand to Telemecanique Sensors

This tutorial, about the Telemecanique Sensors SquareD Pumptrol product, helps you to install it.
For more information, consult the brochure or the instruction sheet: www.tesensors.c...
More innovative solutions on www.tesensors.com

[@rickchristensen3636]

I'm so glad I found this. I forgot to notice the location of wires before disconnecting the white and black wires, thank you

[@rontiemens2553]

Excellent presentation. Confirms I did mine correctly yesterday. Thank you.

[@jimmysoriano1979]

hi great video., but what i have to do to decrease the pressure switch settings to cutoff=40 cutin20

[@nightcrawlerjk2987]

Thanks
I was able to use this video to fix my compressor

[@DP-hy4vh]

I put one of these on my water pump today. The original factory switch on the pump was LeFoo. The contacts were wearing out and every once in a while it would get stuck in the on position.
Hopefully with the new Square D switch, I won't have any more problems.

[@dandufour4257]

Correction: This product will give you DECADES of trouble free service, it's that good. Thank you for such a high quality product!

[@divineyenniehampuy7578]

Can it be possible to use in aircompressor I want to change my pressure switch. Thanks

[@notladrellim8918]

Thank you!! My dad wired it wrong and I couldn't find a good reliable picture or vid till now.

[@Jim-oh2ip]

where do you get the adapter to thread into the plumbing?

[@nawabengineering4388]

This Switch can be used directly on a Water Pipe Line, Right? I was thinking to use a T on a PPRC Water Pipe Line and Tighten it directly over it, Would it Pose any Problem?

[@markwhitnell5752]

Okay, I have an old 10-5psi switch, is it possible to exchange the
springs and put these on a 60-40psi switch? so I now have a new 10-5psi
switch.

[@desertblbuesman]

Hello. Can this switch control a DC pump with AC control power?

[@Hotdog55101]

For the electrical wires - the inside two are from the pump that outside two are from the power - does it matter which goes to which? Do the two on the each need to match something? I can't find out if this matters or how to configure it correctly?

[@samuelreyna82]

Have the same problem.. I have the 3 wire plus ground..

[@samuelreyna82]

I do not know how to connect them the correct way

[@truthpopup]

Are the 30/50 and the 40/60 switches the same switch but simply adjusted differently at the factory? Or are they physically different switches? Can a 40/60 switch be adjusted down to 30/50?

[@larryg7109]

Mine is leaking water from the bottom. Could it be the switch?

[@OrdinaryWorld]

Helps if you put the tape on in the right direction!

[@1topskyrocket]

I really wanted to be able to see the wires and for some reason on my cell phone it's too dark.

[@onegative8887]

All black wires. What planet is that from

[@dandufour4257]

Look closer, the two wires on the right are white, the left are black, it's just a darker video

[@sidtaylor100]

VERY GREAT VIDEO THANK YOU SO MUCH FOR THE DETAIL IT HELPED ME SO MUCH IT WAS EXACTLY RIGHT!

[@itskill3743]

Good Job

[@jascam1]

Take down the video if you're not going to show the wire install to the switch; that is part of the INSTALL.

[@rodneyara]

Spend more time talking about nothing important than explaining the actual procedure of adjustment.

[@ulihanel7078]

Dude, sure enough it was designed the 1940, it shows...

[@TROOTHSEEKERS]

Your teflon tape was installed wrong!