Thank you for your enquiry. We OEM from OKI, we manufacturer in the same factory and our printers are based on 90% of the OKI engine, however the printers are built to our own specification to enable us to print on a wider range of media and heavier stocks.
Thank you for your enquiry - we do not post prices because we sell in many countries all over the world and would need to know what currency to quote you in. If you can provide your country and an email we will send you the relevant information.
Hi Chris, Unfortunately your machine is different. We use the same chassis, but there are quite a lot of differences. 1) The Tool Assembly bar at the rear is different on the Intec ColorFlare, as this is manufactured to enable Both the Flaring (Sleeking) Bar, AND the Perforating and Skewing tools to remain resident in the machine without having to remove them when Flaring (Sleeking) 2) There are 2 Input Roll holders so that Laminate can remain loaded on the machine and Foils can be loaded on the front Input Spool. 3) The Input Spool system used on the front enables Multiple rolls of foil to be loaded simultaneously for dual color foiling 4) There is a different Roller assembly (The Premium Flaring Roller Assembly) which can be added for a better Foil finish. i. (Essentially, Laminate is plastic and as you heat it, you can stretch out the wrinkles, FOIL is based on a metal, with a heat expansion coefficient, which means every 10C increase there is approx. 1mm of expansion every 1m of material. As you foil at approx. 110C, this is almost a 6 - 7mm expansion you have to cope with. On the original machine, you have to handle this by increasing pressure to try to remove wrinkles, but this increases wear, and is not always effective. The premium Flaring Roller assembly system is a dual roller system, that elevates the foil away from the Heated Mirror laminating Roller, and provides silicon smoothing baffles. The purpose is, that by elevating the foil over the heated roller, is does not suffer from the same levels of heat expansion enabling you to run a wider range of foils on a wider range of media with virtually no tension, thus creating better reliability and higher quality foiling.) 5) We use our own operating system/ firmware to enable easier Ramp up of speed and foiling especially after stops. 6) We have different safety covers enabling the additional Roller assemblies to fit and be removed more easily. With regret, neither the additional flaring (Sleeking) arm assembly nor the Premium Flaring Roller assembly are available as an add on option for the original machine, as despite the fact we start with the same chassis, the changes we make in manufacturing are significant enough that you can not retrofit that as an individual to the original machine. In addition different safety covers would be required and different mounting brackets. Best wishes, Mark Baker-Homes.
Hello Amol, We are able to provide a price to you on email - could you please either provide your email to us or email us on: Sales@intecprinters.com and we will deal with your enquiry. Many thanks Intec
Hello Puhazhendi, Thank you for your question. Lamination work is typically done between 105 and 120 degrees C using a mirror roller for smooth finish. It is between these temperatures because it depends on the thickness of lamination and the speed of throughput of the sheets. Should you have any further questions please do not hesitate to contact us at sales@intecprinters.com and we can advise you of the details of your local sales representative. Thank you Intec
Hello Puhazhendhi, The reason laminating film may peel is that you may have a poor quality laminating film or not the correct film for the application - digital toner (possibly has waxes in so requires a stronger 'digital film' or stronger glue than some standard laminates have) or lithographic inks or low pressure coming from the lamination machine. Many thanks Intec
Hello Hemant, Thank you for your interest. Could you please email: sales@intecprinters.com stating the country you are enquiring from or post your email here and your country and we will get a sales representative to send you details. Stay safe! Intec
Hello Tomasz, Thank you for your enquiry. If you email sales@intecprinters.com then we will be able to help you. Or please provide me your email address here and I will pass it on. Many thanks Intec
Sir I am kantha vel from India.Chennai state . Ushafoils@g mail.com.is my mail id can you able to send me the price and availability sizes of machine.if any Rebuilding machine with you.Thanks to you all.
Hello Ahmed, thank you for enquiry. Typically 105° - 110° C for foiling. And we recommend the 'Premium Finish Roller Assembly' to obtain that ultra-flat mirror finish. See our product page here, www.intecprinters.com/systems/colorflare or one of our sales team will happily discuss the details with you if you would like them to call you?
Thanks for your comment. If you would like further information on our foiling and laminating range please contact sales@intecprinters.com. We would be happy to assist
Hello Rose Reklam, could I request you fill in our contact form and we will pass on your details to your nearest dealer: www.intecprinters.com/contact-us/contact-form Kind regards Intec
Your printers look like Oki printers. Who is the original and who is a rebranding ?
Thank you for your enquiry. We OEM from OKI, we manufacturer in the same factory and our printers are based on 90% of the OKI engine, however the printers are built to our own specification to enable us to print on a wider range of media and heavier stocks.
@@intecprinter Thank you, I understand. It make sense.
Could it work with die cut label sheets?
what is the price?
from Maharashtra, India
Machine price
très impeccable
Merci
Why do not say the price???
Thank you for your enquiry - we do not post prices because we sell in many countries all over the world and would need to know what currency to quote you in. If you can provide your country and an email we will send you the relevant information.
@@intecprinter plis whtsapp +971508814247
Mail royalbookbinding20@gmail.com
What does the premium finish flaring assembly do? I have the standard version of this machine direct from manufacturer
Hi Chris,
Unfortunately your machine is different.
We use the same chassis, but there are quite a lot of differences.
1) The Tool Assembly bar at the rear is different on the Intec ColorFlare, as this is manufactured to enable Both the Flaring (Sleeking) Bar, AND the Perforating and Skewing tools to remain resident in the machine without having to remove them when Flaring (Sleeking)
2) There are 2 Input Roll holders so that Laminate can remain loaded on the machine and Foils can be loaded on the front Input Spool.
3) The Input Spool system used on the front enables Multiple rolls of foil to be loaded simultaneously for dual color foiling
4) There is a different Roller assembly (The Premium Flaring Roller Assembly) which can be added for a better Foil finish.
i. (Essentially, Laminate is plastic and as you heat it, you can stretch out the wrinkles, FOIL is based on a metal, with a heat expansion coefficient, which means every 10C increase there is approx. 1mm of expansion every 1m of material. As you foil at approx. 110C, this is almost a 6 - 7mm expansion you have to cope with. On the original machine, you have to handle this by increasing pressure to try to remove wrinkles, but this increases wear, and is not always effective. The premium Flaring Roller assembly system is a dual roller system, that elevates the foil away from the Heated Mirror laminating Roller, and provides silicon smoothing baffles. The purpose is, that by elevating the foil over the heated roller, is does not suffer from the same levels of heat expansion enabling you to run a wider range of foils on a wider range of media with virtually no tension, thus creating better reliability and higher quality foiling.)
5) We use our own operating system/ firmware to enable easier Ramp up of speed and foiling especially after stops.
6) We have different safety covers enabling the additional Roller assemblies to fit and be removed more easily.
With regret, neither the additional flaring (Sleeking) arm assembly nor the Premium Flaring Roller assembly are available as an add on option for the original machine, as despite the fact we start with the same chassis, the changes we make in manufacturing are significant enough that you can not retrofit that as an individual to the original machine. In addition different safety covers would be required and different mounting brackets.
Best wishes, Mark Baker-Homes.
Intereting explanation, thanks Mark. I'm popping down on Wednesday to see your Colorcut machines!
Great! we look forward to welcoming you, Chris. (PS: this is Shaun in the marketing dept, I'd be interested in seeing a sample of your astro-photos).
ha, where did you see about my Astro Photos? I have some on facebook page facebook.com/chriscorkphoto or 500x (chriscorkphoto) also :)
Sir, What is the machine price? In India or european Country? Where is it available?
India price
price please
Thank you for your enquiry. Please could you tell me which country you are in and supply me with your email address? Many thanks
Rate and country
Hello Amol, We are able to provide a price to you on email - could you please either provide your email to us or email us on: Sales@intecprinters.com and we will deal with your enquiry. Many thanks Intec
Excelente miaaauu
what is temperature for laminating work?
Hello Puhazhendi,
Thank you for your question. Lamination work is typically done between 105 and 120 degrees C using a mirror roller for smooth finish. It is between these temperatures because it depends on the thickness of lamination and the speed of throughput of the sheets.
Should you have any further questions please do not hesitate to contact us at sales@intecprinters.com and we can advise you of the details of your local sales representative.
Thank you
Intec
Sri send price
what is the reason some time laminating film peelout?
Hello Puhazhendhi,
The reason laminating film may peel is that you may have a poor quality laminating film or not the correct film for the application - digital toner (possibly has waxes in so requires a stronger 'digital film' or stronger glue than some standard laminates have) or lithographic inks or low pressure coming from the lamination machine.
Many thanks
Intec
What is the price of the machine?
Thank you for your enquiry. Please can you tell me which country you are in and supply me with your email address? Many thanks.
@@intecprinter I have WhatsApp 964 7718533808
@@منتظرالطائي-ر9ظ Thank you for your response, do you have an email address please?
@@intecprinter 964 7718533808
How much price of machine
Hello Hemant, Thank you for your interest. Could you please email: sales@intecprinters.com stating the country you are enquiring from or post your email here and your country and we will get a sales representative to send you details. Stay safe! Intec
Prise
Sir, Please send detail AND price
Thank you for your valued enquiry. Please can you tell me which country you are in and supply me with your email address, many thanks.
@@intecprinter India , Lucknow , excellent.tahir@gmail.com
Please send this machine details and best Quatation
Thank you for your enquiry Gaurav, can you advise your email address and country you are located in please?
hi I am from Seychelles how can I get a Quotation
email address stfidelemd@email.sc
Thank you for your valued enquiry, I will send you the relevant information via email.
We are from Poland. Who can I contact about cooperation ?
Hello Tomasz,
Thank you for your enquiry.
If you email sales@intecprinters.com then we will be able to help you. Or please provide me your email address here and I will pass it on.
Many thanks
Intec
please send me price, thanks
Thank you for your enquiry. Please could you tell me which country you are in and supply me with your email address? Many thanks
Sir I am kantha vel from India.Chennai state . Ushafoils@g mail.com.is my mail id can you able to send me the price and availability sizes of machine.if any Rebuilding machine with you.Thanks to you all.
Dear Sir
What is the appropriate temperature for foil work?
And what type of roller used in foil?
Regards
Hello Ahmed, thank you for enquiry. Typically 105° - 110° C for foiling. And we recommend the 'Premium Finish Roller Assembly' to obtain that ultra-flat mirror finish. See our product page here, www.intecprinters.com/systems/colorflare or one of our sales team will happily discuss the details with you if you would like them to call you?
Need this machines
Pls send me details at theprintmediabd@gmail.com
@@zahirulislam9035 Thank you for your enquiry. Please can you tell me which country you are in? Many thanks
Wooow
price plz?
Thank you for your enquiry, one of our sales team will contact you very soon.
Hi interest
Could I have the machines descriptions & best qout of the machines please
Mail
Thank your your enquiry - could you provide your email address and which country you are in - and we will supply the details you require. Thank you.
99Crore
Thanks for your comment. If you would like further information on our foiling and laminating range please contact sales@intecprinters.com. We would be happy to assist
whatsApp
Thank you for your enquiry, our sales team have been notified and will contact you with the information you require very shortly.
Hello Rose Reklam, could I request you fill in our contact form and we will pass on your details to your nearest dealer: www.intecprinters.com/contact-us/contact-form
Kind regards
Intec