Van Life HACK: The BEST Rack for Your Sprinter!
HTML-код
- Опубликовано: 15 июн 2024
- I was thinking to build this van rack to suite my needs and leave room for eventually loads of cabinets the long stuff i am going to carry them on the roof rack that i am intending to install later, anyway this is first part of the video in the second part i am installing another bed slide at the back same high as the first one so the will be level up so i can put flat pack furniture and boards sheets i used 12mm flywood on floor and 6mm to panel the walls for the shelves used 9mm sheets to keep the weight low and to balance the weight and for the strength of the slider bed i used 18 mm sheet to build the shelving cab as that is attached to the sliding bed only on bottom as fixings i used mg threaded nuts and 6mm bolts to fix the runners on to the floor and metal L bracket with countersink bolts to fix them to the runners as well i use noice reduction self adhesive band for the wall at that van sounded like a drum, thanks for watching and fell free to ask me anything about this builds, i will leave some amazon links below so you guys can find some tools that i have used to do this protect by buying frome this affiliate links you will pay the same porice as you would usually only i get a small percentage from amazon that will help me to create more content and invest in more gears to make more quality videos thanks again here are amazon affiliate links
Heavy duty runners van and camper van amzn.to/3VCGSd9
M6 bolts 16mm amzn.to/3zikWg4
Protector bench dogs mft/3 amzn.to/45Gkg07
Van noice reduction stickers amzn.to/45Ch2L9
Extention springs amzn.to/3RCxntd
Heavy duty van floor matting amzn.to/4czy6nk
M6/ 10mm threaded nuts amzn.to/3VEClan
- [x] Camera tripod amzn.to/3RDn3SN
- [x] Phone tripod amzn.to/3ZEC0G1
- [x] Bessey clamps amzn.to/3TPZpTH
- [x] 5 mm BIT amzn.to/3sJh8S0
- [x] Fine cut 42 teeth blade amzn.to/3taiPHY
- [x] Festool fastening clamp amzn.to/43RLf8d
- [x] Festool lever clamp amzn.to/3xb88Hg
- [x] LASGOO amzn.to/3t0okth
- [x] CANOPY amzn.to/46qYiwL
- [x] 5mm pilot dril bit amzn.to/3rC3nnD
- [x] Festool cart amzn.to/3QyPAIl
- [x] Gide rail 800 amzn.to/3RJ3JUm
- [x] Gide rail 1400 amzn.to/3rrD3wF
- [x] Drill 12v amzn.to/3PFwJth
- [x] Rails conectors amzn.to/3LMoUki
- [x] Ks60 mire saw amzn.to/48wuK3j
- [x] Jig saw blades carvex amzn.to/3ZGBvLz
- [x] Quick action clamp guide rail amzn.to/46vym3y
- [x] Bosch blades jigsaw amzn.to/3RHb6eI
- [x] Rawl setting tool amzn.to/3ZIQ4yj
- [x] Pica fine pencil amzn.to/3Q1XaLk
- [x] Pica reserve leds amzn.to/3F0QWF3
- [x] 2. 5 mm pilot drill amzn.to/45bOlCN
- [x] Tajima tape measure amzn.to/3LG5wp1
- [x] Red blade amzn.to/3PEhQrk
- [x] Yellow blade 42t amzn.to/3tm8YPk
- [x] Yellow blade 28t amzn.to/3LKfnKA
- [x] Blue kapex 60 amzn.to/46zk1TW
- [x] Blue 52 t amzn.to/45cWXJy
- [x] Maffel red 160 tsc55 amzn.to/46A9M1I
- [x] Ks60 universal blade yellow amzn.to/3tjmP9m
- [x] Glue miter fast amzn.to/45thN7C
- [x] Jig saw amzn.to/46vMf2g
- [x] Tcs55 keb amzn.to/3S1Q1fb
- [x] Miter fast amzn.to/48U7Z9H
- [x] Table saw amzn.to/3vT9ki2
Awesome video, really love the pride you take in your work, everything looks great and well organised. Differently blur out your license plate..there are real scumbags who will steal your tools, livelihood. Differently make sure the van is protected, I am sub to another carpenter channel a d his van was broken into, they stole most of his expensive tools. Anyway, great job 👍.
Thanks a ton! I never leave tools in van i will take to the job exactly the tools i need the only think i leave in those shelves are just consumables like connectors biscuits screws etc , i know last year they tool my leser level and some bits nothing special but they will add up i can not do much is the time we living i try tu be cautious as no matter how many safety precautions you take they will find a why to brake into your van thanks again for your comment !
love it , i've been working for this dream for years now , having a car with all my wooding tools is my only dream hope one day come true , keep going buddy many ppls inspired by your vids and i'm one of them ❤❤
Love to watch & 100% enjoyable in this one hour video ❤
Glad you enjoy it! Thanks so much for watching !
This is very cool, you are a master of your craft
thanks so so much for watching this video !
I am in awe of your work. You're the carpenter we all strive to be! If anyone deserves to have all that top dollar gear, it's you. Hats off to you mate
Also, where can I get myself some those drawer runners?
Thanks nice compliment i got them from this site vadania.co.uk/shop/
@@CAVjoinery thank you for your reply. I've been looking for something like this for a long time!
Propre efficace comme toujours dans tes vidéos merci 🙏
You really are impressive sir!
Master piece of a video
Thank so much for watching !
Superb 👍
Thank you! Cheers!
Fantastic video !!! Great build !!!
Thank you very much! It is not finished i am still missing a second pairs of runners so i will put onother short update video hopefully next week !
@@CAVjoinery I will look forwaed to your next video, you are a very gifted crafts person thank you
I watched again and still found it interesting 😂
:)) glad to hear that i will post a video with the final project i think this weekend thanks for watching !
I recently did the racking on my van. Now I think I need to do it again. It's much better than it was though. I put all my racking by the side door and was thinking about runner to the rear doors for the mitre and table saw. I like some of the ideas you have used and will definitely copy some. Thanks for uploading such a good video
i put a false floor in my van about 150 mm so i can get on sheet material and timber and keep it away from my tools , its a good idea the pull side door however i would rather have a site box as ppl breaking into vans these days is beyond a joke
Thanks , i did this because i always carry all may tool on site i only leave bits inside the van so everything is there to be easy access and have a bit room to sore some eventually cabinets or doors etc i will have a roof rack for the long stuff added later
@@CAVjoinery it's good design and I carry a lot a of sheet material, yeah my tool kit is almost identical to yours and I have to split my tools, I am going to put bi fold shutters on my van that can be made custom size for the side door and back door, for added security
@@tonyconnor5691depends where you live and if you're on site. I'm not really either of these. Have fitted quality deadlock. If I was anywhere in a major town I would definitely consider the locking metal drawer. Tool sales are being banned at car boots in many areas without proof of purchase and eBay Facebook should also copy this so hopefully that might improve things.
우와 진짜 대단합니다
멋진 작업을 공유해 주셔서 고마워요
저도 아이디어를 차용해 한번 해 볼게요😅😮😊❤❤❤
Great video! Only wish my work van was half as nice 😅
Thanks you can organise it it cost me arount 300 to do this one
Espectacular muy buen trabajo
Thanks 🙏
классный получился проект,,,,я бы на вашем месте сделал из выдвижного ящика стол с откидной ножкой для жесткости для той же торцевки или циркулярной пилы, ну после того конечно как убрать с него ящики с инструментом)) Смотрю вас уже пол года хороший иструмент у Вас!!! Удачи вашему каналу и интересных проектов!!!
Oh thanks so so much appreciate your tip i will take that into consideration thank you very much for following my channel !
Nice job 👍😍
Thank you! Cheers!
@@CAVjoinery yes…🥂cheers !
I have a metris long wheel base. You might call it a veto. I got RV drawer slides. (They’re designed for large motor homes to access storage underneath) there’s all kinds of lengths etc. I got the 80”. I made it wide enough to hold two systainers wide. It will cantilever out of the back doors of my van 55”. There I have the csc sys 50. 😊
Ih i see i got you ! This van i will use it just to care the tools i need for a job and i never leave tools inside the van we living hard times where vans are braking in tools gets stolen etc so i design this to be light in weigh and easy to access
Loved the video! Been thinking of that maxus myself, nice to see how one would outfit it.
Personally I was thinking of going with a subfloor to transport plaster and ply.
I will have roof rack ro occasionally end panels this ways works better for my needs is not finished yet i will have another bed slide to help me access easier the table saw and miter saw and i will not leave any tools on van anyway i only leave the bits boxes
Oh, that's very smart to lower centre of gravity! A custom welded or bolt on subfloor box would be brilliant!
Wie immer perfekte Arbeit👍👏
Thank you 🙏
Very instructive vidéo, I just wanted to ask you if you could give us a tour of your van and your tools.
Hey thanks so much i will add a complet video in the coming days as is not finish as you saw the back side i need to put another bed slide and some small shelves
Extraordinario , profesional y bonito trabajo👏👏👏👏👏
Thanks a lot glad that you enjoyed my video !
정말 대단하십니다ᆢ
좋은영상 잘 볼수있게 해 주셔
감사해요ᆢ
앞으로도 좋은 아이디어
부탁드릴께요ᆢ
감사합니다!!!
Thanks so so much for the comment appreciate it!
Very nice job, like all the other jobs you are doing. You forgot to hide your number plate the last few seconds of the video.
You are right! Thanks for the comment i will take care of it !
I new you wood have the best work van in the world 🌎 it's first class....
I love it!
Question. Where does your material go? I assume you cant fit very long material. Side note: love your craftmanship in your vids
I intended to install roof rack as well thanks
👍👍👍👍Professional, my respects.
Thank you very much! Appreciate it
Bro what?! that's so fire
I was looking to not add to much weight and to be strong as well but also to keep some space for eventually cabs or bits bringing to the job from the suppliers now and then! Thanks for watching !
@@CAVjoinery I think he meant "fire" as in the fire emojii. Thin ply is the way. Boat builders build cabinets like this. My main concern for ply would be moisture resistance. Does it get very wet in your part of the UK?
Awesome build, quick and practical. The diagonal shelf design is smart. Some elastic bungee cord may help to secure the systainers some more if needed. I would have added adhesive neoprene or foam strips also on the wall behind each systainer to prevent rattling. The drawer pull handle is clever too. Load ratings and durability on these big drawer slides can vary. Are you happy with yours so far?
They look solid i went for this build because i never leave tools inj van all tools are carried inside the job i only use those shelves for conectors and bits and yeast those looks strong runners i have them from vadania.co.uk they have some heavy duty hardware
@@CAVjoinery Ah, I see! That's a good idea. Yes, I've heard from British colleagues here in Sydney that theft of tools is a very serious and rampant problem over there. I am designing a similar solution as yours except I want to to take out as many tools as possible in one go and simply roll into a job site without having to go back and forth several times to the vehicle.
Perfectionist
Thanbks so so much glad that you like it !
nice build as always .i use a lot of the same tools..i would add a rotating air vent to the roof that keeps fresh air flow through the rear cab space, im assuming its in the uk? .. the vans iv had are always having the same problems with stored tools.. moisture and condensation, then mold and rust. airflow in through the roof vent and out through a secondary vent.
I was thinking of that they have some vents but seams that they aren’t enough for air flow,although i have to take in counting the roof rack i will add on later thanks a lot for the tip !
Very nice👍
What is the brand name of that green jacket you are wearing?
SnickersUK 34:32
It is snickers workwear they are not cheap workwear clothes but in my opinion they are durable and i can feel the quality of the material not to mention the design with flexible material on joints etc
What brand of interlocking biscuits are you using on this project? Did you get the 290EV? How are you finding the mileage? Very useful internal coachbuilding. 😎
Hey i have used lamello conectors p14 clamex zeta and p10 tenso with preload clips is van e deliver 3 called and the mileage is taking care my accountant to be honest i do not know how is working yet anyway thanks so much for watching my video!
@CAVjoinery thanks for the connector update, I'll be checking them out 😉 happy travels!
Very cool!!!
Thanks 🙏
Hello Cav ! How are you ? I love your work And If poosible ,I want like to work with you . THANKS😀
Hey there i am working alone and i am not own a company i am just sole trader sorry i can not help with that
سلام وقت بخیر مثل همیشه عالی
Hello to you to thank you for watching this video !
@@CAVjoinery 🙏🙏🙏
Great job, link to runners please. 👍
I bought it from this site vadania.co.uk thanks no affiliate link this
Super!!!✌🏻👍🏻🔥
Thanks! 😀
Здравствуйте, как вас зовут? В каком городе вы живете?, как вы начинали свою карьеру?, мне очень интересны ваши видео , вы хороший специалист, и у вас отличный инструмент.
Hey there i am living in sheffield uk came here in 2017 i was working for amazon for few weeks did not liked than i have started working for a small company to deliver and install flat pack furniture similar to ikea and after one yer i have join to a kitchen fitter and stated saving money and buying my first drill i was watching a lots of youtube videos and i try to learn everyday something new like woodworking and furniture fitting and how to take videos how to edit videos etc and i still learning thanks for watching i wish you good luck 🤞 as well
Hi.
Very nice job!
I watch all your videos of kitchen installation.
How do i contact you for my own kitchen instillation?
Thank you.
Check description there is my email address
Thank you for your reply.
Супер 👍
Thanks a lot
👍👌
Thx 🙏
Ah, enfin nous allons voir la camionnette de superman ☺️
Thanks that is a lot of compliment ! ☺️
Je suis poseur de cuisine aussi mais vous êtes bien plus complet que je ne saurais l’être actuellement.
Le bon outils pour la bonne action, la précision.
And one day it will be emptied by the long fingers. It’s not if but when.
Is usual empty unless they will be happy with some screws and connectors that’s why i have beds instead of shelves so i can easily take the boxes out the van i never leave tool in van
What’s a CHARPENTER??
👌🔥🔥🔥🔥
THANKS 🙏
🔥🔥🔥
Thx
Cover your number plates please,
I missed that but it is ok i did it finally thanks a lot !
Вот это да !
Thanks 🙏
nice.esti roman?
Mersi, da sunt din romania !
@@CAVjoinery ești foarte priceput prietene. Îți urmăresc video urile și am învățat multe din ele. Mulțumesc și succes în continuare cu vizionarile
What are those stickers for?
They are sound proof as the tin make the cargo area sound like drum
Is it a new van
Yes it is !
😊👍👍👍💎💎🎉
Thanks
What size van is it?
L1 h1
😯🙂👍👍👍✊
THANKS 🙏
Спецназ
:)) cheers mate
@@CAVjoinery special forces
@@CAVjoinery cheers - ура ?
Ура это в 1945
Nice Work, but very ugly music 😂