THANK YOU! I bought my machine new and immediately this was an issue - imagine my frustration, especailly when I found out the nearest Singer warranty service person is over 100km away and I don't own a car! Grrr. This tutorial was exactly what I needed! You're awesome.
I am so HAPPY. I just repaired my M1000 that stopped sewing after a bobbin thread/needle thread/tension jam. I bought a folding Craftsman 9-key metric hex kit at Lowe's for $10. The smallest hex wrench, the 5/64, fit perfect. BUT I loosened the 2 hex screws under the machine too much. That made the manual hand wheel stop working (it no longer moved the black bobbin case OR the 2 hex screws at the bottom!! Thought I was screwed because now nothing turned so I could not retighten the hex screws because they were no longer visible beneath the machine. So I laid the machine on its back and reached into the black bobbin "cup" on top, and manually moved it so I could see the hex screws at the bottom again. It worked! Then I tightened up one hex screw slightly (but not all the way). Next I set the machine upright and attempted the fix again by moving the black bobbin "cup" so it aligned with the needle as it came down (as KT shows us). Then I put the bobbin thread back in, screwed the white plate back into place, and tried to pick up the bobbin thread with the needle. IT WORKED!!! Then I sewed a few inches. Beautiful. Next, I am going to fix my older, larger Singer that has refused to do a zigzag stitch for years. It only does straight stitch. I read this is also a timing problem. (●'◡'●)
Just got a singer M1000 pre owned. I am a total noob and i was frustrated to see that the thread won't loop from the bobbin. Your tutoral was just the one i needed. Thank you!!
I just want to say thank you!!! I just bought a new but used machine. I'm a complete newbie to machines. I haven't sewn in 15 years. The first project went fine, it was a basic one. Once I was comfortable, I said I needed to do a little maintenance ie lint. Well, when I went to start the next project, I couldn't figure out why the bobbin wasn't catching. Hours of searching the internet. I came across your video, and it was the problem! You are a life saver, and I can't thank you enough. I was on the verge of tears bc I was so frustrated. 🎉🎉🎉
Just bought Singer M1005 yesterday and got the same problem. Trying to fix by following other tutorial but it makes my energy drained. Then your video helped me, it works really well with not much effort, perfect for a machine noob like me. Thanks a bunch man!
THANK YOU!I just bought a used singer simple and the lady who sold it did NOT tell me there were any issues, I was almost ready to toss it out the window :( Your video did the trick and now it's catching the bobbin thread!
Thanks!! Helped me fixed that issue. Singer should have your video on their website and also include instructions how to fix it in the manual as it seems to be a common one....
Wow! This is so amazingly helpful! My machine stopped working over 2 years ago after only about 2 uses and I couldn’t figure out what was wrong. I was planning on getting another one but decided to find help on RUclips. This video really helped! I am now able to sew all my clothes that had been waiting for the last couple of years. Thank you so much for these instructions.
Thank you so much for this video. Unfortunately I loosened the allen bolts all the way and was totally unable to put them back into their holes so I've just had to take the entire casing off the machine to access that drive shaft enough to thread them back in. This is a very poorly designed machine in my opinion. Great video tho, thank you!
It's likely the screws haven't been loosened enough. If you're like me you're having an issue where the screws don't actually turn, and forcing the Allen wrench to turn just straps the wrench
I need help. I have this machine and I've had to adjust the timing a few times. This time that I adjusted the timing, the tray that my bobbin goes in keeps getting caught on the black piece that is below the presser foot. This piece seems to lift up but I don't know why it's suddenly getting caught when I'm trying to thread my machine. please someone help!
Thank-you for your video i had same issue. It did fix it, but now i have a problem with the needle part i think my machine is defective (alot of problems since the start and it was brand new😢
I listened my screws and adjusted the catch/black part but when I flip over to re tighten the screws to test they are moved and only show when I re turn the black part back to where it was?!? How do i re tighten the screws after? I wish you showed that step im so overwhelmed 😰
Hello, I wanted to thank you for your video. I am having so much problem losing the screw. Can you tell me if I am supposed to turn left or right to be able to unscrew the screw under the sewing machine to adjust the timing?
I have an issue, when I pop off the small white circle peice on the bottom of the machine. There's no visible little screw to loosen. And when I turn the nob nothing turns like in your video
The two separate hex screws are not always immediately seen. But if you turn the "wheel" toward you a little, the mechanism moves and they will appear, one after the other. You might need a flashlight to see them.
Make sure to remove the presser foot to make more room. My plastic plate slides out toward the back. Also, there is a small square hole in the front of that plate. When I stick a tiny screwdriver inside it, it triggers a lever that releases it.
I neeed help, my machine is called New Ideal Athina 8855 it is nearly like yours but whenever i try to step on its brake it just makes sound but doesnot move the needle at all please show me whats wrong with it since it doesnot stitch at all
This thing is the biggest piece of plastic junk just got it today and I'm packing it up to return edit: just bought a Singer Heavy Duty and used it 1 day before it had the same issue, the cam is coming out of alignment and not threading the bobbin thread after 1 jam. Its time to get a Brother....
THANK YOU! I bought my machine new and immediately this was an issue - imagine my frustration, especailly when I found out the nearest Singer warranty service person is over 100km away and I don't own a car! Grrr. This tutorial was exactly what I needed! You're awesome.
Thank you! I've been sewing for about 60 years now, and I've never seen this problem before.
I am so HAPPY. I just repaired my M1000 that stopped sewing after a bobbin thread/needle thread/tension jam. I bought a folding Craftsman 9-key metric hex kit at Lowe's for $10. The smallest hex wrench, the 5/64, fit perfect. BUT I loosened the 2 hex screws under the machine too much. That made the manual hand wheel stop working (it no longer moved the black bobbin case OR the 2 hex screws at the bottom!! Thought I was screwed because now nothing turned so I could not retighten the hex screws because they were no longer visible beneath the machine. So I laid the machine on its back and reached into the black bobbin "cup" on top, and manually moved it so I could see the hex screws at the bottom again. It worked! Then I tightened up one hex screw slightly (but not all the way). Next I set the machine upright and attempted the fix again by moving the black bobbin "cup" so it aligned with the needle as it came down (as KT shows us). Then I put the bobbin thread back in, screwed the white plate back into place, and tried to pick up the bobbin thread with the needle. IT WORKED!!! Then I sewed a few inches. Beautiful. Next, I am going to fix my older, larger Singer that has refused to do a zigzag stitch for years. It only does straight stitch. I read this is also a timing problem. (●'◡'●)
Just got a singer M1000 pre owned. I am a total noob and i was frustrated to see that the thread won't loop from the bobbin. Your tutoral was just the one i needed. Thank you!!
I just want to say thank you!!! I just bought a new but used machine. I'm a complete newbie to machines. I haven't sewn in 15 years. The first project went fine, it was a basic one. Once I was comfortable, I said I needed to do a little maintenance ie lint. Well, when I went to start the next project, I couldn't figure out why the bobbin wasn't catching. Hours of searching the internet. I came across your video, and it was the problem! You are a life saver, and I can't thank you enough. I was on the verge of tears bc I was so frustrated. 🎉🎉🎉
Im literally in the same situation 😢 this video is a god sent
Just bought Singer M1005 yesterday and got the same problem. Trying to fix by following other tutorial but it makes my energy drained. Then your video helped me, it works really well with not much effort, perfect for a machine noob like me. Thanks a bunch man!
I dont have the other tool i only have the mini one
THANK YOU!I just bought a used singer simple and the lady who sold it did NOT tell me there were any issues, I was almost ready to toss it out the window :( Your video did the trick and now it's catching the bobbin thread!
Thanks!! Helped me fixed that issue. Singer should have your video on their website and also include instructions how to fix it in the manual as it seems to be a common one....
Wow! This is so amazingly helpful! My machine stopped working over 2 years ago after only about 2 uses and I couldn’t figure out what was wrong. I was planning on getting another one but decided to find help on RUclips. This video really helped! I am now able to sew all my clothes that had been waiting for the last couple of years. Thank you so much for these instructions.
Mine stopped working as well after two uses. I am going to try this today.
I thought he was using a screw driver in the bottom of that machine. I am still to get the appropriate key for the bottom of the sewing machine.
I got my Allen hex key today and fixed my machine 🤸🏾♀️🤸🏾♀️🤸🏾♀️🤸🏾♀️💃🏽💃🏽💃🏽💃🏽
Thank you, my new machine had the same issue and thanks to this video I was able to fix it 🙌🏻
My problem in singer M1005 solved as per your instructions.. Thank you very much .
Ahhhhhhh thank you so much!!!! I picked up this machine for $13 at Goodwill. I almost threw it away. Then I found your video! Thank you.😊
I can’t thank you enough, happy to report my machine’s up and running again!
Thanks for help! 👍🏼Exactly the video I needed. The only video that I see that helped me with the specific problem!!!
Thank you so much for this video. Unfortunately I loosened the allen bolts all the way and was totally unable to put them back into their holes so I've just had to take the entire casing off the machine to access that drive shaft enough to thread them back in. This is a very poorly designed machine in my opinion. Great video tho, thank you!
True even the registered singer tecnicians say so and advice against it's repair
I m from Pakistan I just want this video thank you u so much u solve my problem 🤗🤗🤗🤗🤗🥰🥰🥰
My machine is working again. Thanks so much!!!!
Any tips on how to get that screw loose? It's too tight and just stripping my wrench
I'm replying very late but I used a wrench to hold the Allen key to get more torque
How do you get the bottom piece open
Saved my night. Thank you!
bro it keeps moving the needle when i move the black part
I am having the same problem
Any solution found ?
It's likely the screws haven't been loosened enough. If you're like me you're having an issue where the screws don't actually turn, and forcing the Allen wrench to turn just straps the wrench
@@aster6969 i took ts back bro it got annoying
My machine had a other set of them little Allen screws I tried wrong ones at first
This made the trick!!! I would add that there are TWO Allen screws on the bottom (I'm not a native speaker, so maybe I missed that part)
I need help. I have this machine and I've had to adjust the timing a few times. This time that I adjusted the timing, the tray that my bobbin goes in keeps getting caught on the black piece that is below the presser foot. This piece seems to lift up but I don't know why it's suddenly getting caught when I'm trying to thread my machine. please someone help!
I think the problem is that the tray that my bobbin goes in is moving and turning and getting caught
Have you found a solution? Same problem here@@ChristineMichelleYT
I’ve got it open, I see the two screws but for the life of me I can’t loosen them- any tips y’all?
Thank-you for your video i had same issue. It did fix it, but now i have a problem with the needle part i think my machine is defective (alot of problems since the start and it was brand new😢
Loosened the two screws but the black part with catcher will not move enough to be in the right position.
have u found a solution? 😅
Thanks! exactly the video I needed ❤
I listened my screws and adjusted the catch/black part but when I flip over to re tighten the screws to test they are moved and only show when I re turn the black part back to where it was?!? How do i re tighten the screws after? I wish you showed that step im so overwhelmed 😰
Excelent video just fix the problem thanks!!!
Very good video. We solved the problem at home. Thanks sir👍
How to position the bobbin wheel back again? It jumps off the place when I try to rotate the hand wheel.
Hello, I wanted to thank you for your video. I am having so much problem losing the screw. Can you tell me if I am supposed to turn left or right to be able to unscrew the screw under the sewing machine to adjust the timing?
Usually with most mechanical things, the rule is righty tighty, lefty loosey. So I plan to turn slightly to the left to loosen that screw.
Broo this helped me SO MUCH I appropriate his video 🙇🏾♀️🙇🏾♀️🙇🏾♀️
No problem!!
@@kt7967 actually what kind of screw driver did u use all mine are either to big or too small?
The link to buy the alley key doesn’t open, please help! Thanks
I’m going to go buy the tools I needed this like yesturday hopefully it fixes it thank you 😊
Help !
I have loosen the screws and did everything like in the videos and it is still not picking the treat underneath 😢😢
Did you ever find a solution? My machine just got a timing issue 😢
We are trying but I can’t move the black piece that you move with your hand
I am also having the same problem.
Same here
INCREDIBLE HOW CALM YOU STAY ... O ENTHUSIASM TO THROW THIS STUPID MACHINE OUT THE WINDOW
Thank you! I fixed it and I really didn't think I would be able to.
Oh wow!!!! This worked. I had to go to the hardware store to get an Allen hex key size 2mm. Thank you so much.
Traductor en español
Mi máquina no coje el hilo de abajo
this is helping but what can I use for the screw that we have to losen in the machine
What is the size of the ale key you used?
2 mm hex key
That is very Nice of you to help
Thank you so much from Italy!!!!!!
I fixed it. Thank you so much
Thanks a lot I was having this problem and it works ❤😅
the lil bolts im suppose to loosen are super tight, and its hard for me to turn it but i believe this is the problem with my machine.
SAMEEE
@@kpop-lover615I str8 up forced it and they popped real loud .. nothing broke tho seems like they were just stuck so js force it
Fantastic fixed problem
Lifesaver! Thanks bro 🙏🏽
if i lost my screwdriver key thing, what can i use?
Buy a metric hex kit, sold at most hardware stores for between $7-10. It will have the tiny mm sizes you will need. I got mine at Lowe's.
I have an issue, when I pop off the small white circle peice on the bottom of the machine. There's no visible little screw to loosen. And when I turn the nob nothing turns like in your video
The two separate hex screws are not always immediately seen. But if you turn the "wheel" toward you a little, the mechanism moves and they will appear, one after the other. You might need a flashlight to see them.
Thank you so much brother, it helped a lot!!!! 👍🏼👊🏼
Thank you so much. Most helpful!!
Whats the tool you used to loosen up the black part?
It's called a 5mm hexagonal screw driver you can get it off of Amazon
@@mystery0cean129 thank you
Thanks!! That’s so helpful.🎉
Thank you so much. It worked !!!
THANK YOU SO MUCH YOU ARE MY ANGEL
i can’t get the plate up on top of the bobbin
Make sure to remove the presser foot to make more room. My plastic plate slides out toward the back. Also, there is a small square hole in the front of that plate. When I stick a tiny screwdriver inside it, it triggers a lever that releases it.
it helped me and my dad
I neeed help, my machine is called New Ideal Athina 8855 it is nearly like yours but whenever i try to step on its brake it just makes sound but doesnot move the needle at all please show me whats wrong with it since it doesnot stitch at all
Thanks for the help😊
When catch is rotated, the needle goes up and down. You can't just rotate it to the needle. I need a little help.
Nope didn’t work. I tried everything and retreading machine. Still needle comes up empty. What now?
One of the screws at the bottom was so tight I couldn’t make it budge, so I’m not sure what to do there
I would try a little oil or lube inside the stuck one and then try again the next day. Mechanical parts can fuse together just from humidity.
What if that didn’t work?
Very good tank for this
THANK YOU SO MUCH!
You're welcome!
It works thank you!
The little allen wrench screws are so tight I can't loosen them at all
Can i also apply this method to an embroidery machine?
Yes I ve got a brother v3 and brother 750
Awesome! Thank you!
Thank you would help me for reasons I don't understand
My machine it’s not working I was trying but I’d know how repair bro can solve my problems and help me
The bottom part cannot be opened. Pls help
I can’t get it either
I was struggling with an exacto knife but I grabbed a small kitchen knife and it popped right off
You need a very thin blade like a razor blade
Thank you for help
Como se pone la pieza donde va la bonina
Thanks bro😊
Traductor en español
Cómo lo puedo buscar en español
Gracias😊 ❤❤❤
Thank you!!!!
My machine is not sewing remedy
thank you
La aguja queda arriba cuándo pasá el enganche
Meh im trying to find the cover i need
No sale poque la aguja se queda arriba cuándo pasa el enganche por ai
THANk YOU!!!!
Thanks 😌
thanks
This thing is the biggest piece of plastic junk just got it today and I'm packing it up to return
edit: just bought a Singer Heavy Duty and used it 1 day before it had the same issue, the cam is coming out of alignment and not threading the bobbin thread after 1 jam. Its time to get a Brother....
I fixed the timing, but now my bobbin thread is loose
Por favor yo quiero el vídeo en español
Tiene subtitulos
La mía no sale l
this is my last resort lets see if it works brb!
I’m about to just throw this stupid machine away. This always happens.
We have singer M3220
Fuck bro thank YOU😭
Yo lo quiero en español
Dude has to be trolling. His machine isn’t even functioning properly. 😂
Yo Ise todos e
Yo is
Thank you so much for this🥹 I would have been absolutely lost