How To Rebuild BMW M3/M5/M6 S65/S85 Throttle Actuators
HTML-код
- Опубликовано: 1 апр 2022
- GET YOU SOME MERCH AT www.YEVSBuilds.com
Donate to my channel: paypal.me/ynd94?country.x=US&...
Make sure to follow my Instagram for some of behind the scenes updates @YEVSBuilds
These are the gears I purchased: www.odometergears.com/product...
Music released by Carbon Citizens
/ carboncitizens
Click Here To Stream On All Platforms: fanlink.to/CCallstream 
Авто/Мото
Make sure to like / share / subscribe 🤘🏻
drilling into the shaft is completely unnecessary. It already has a flat side so a pin is completely redundant. JB weld in the knurls and let it set is all you need.
All that drilling does is increase the chance of mucking up the part and destroying the shaft beyond repair.
Was just looking at buying both actuators brand new until I saw this. This is doable ! Appreciate the video !
Happy to help!!
Hello Y.E.V.S BUILDS,
Loved your video!
Next time and for viewers, recommend performing all work on the output shaft before assembly. You removed the shaft to file the "peen mushroom" to install the gear. Nice cross drill, but bond gear while it is out and on the bench, not in a confined area. Then just reassemble to the throttle actuator housing.
NOTE: To do requires removing arm that attaches to the throttle body link, but only held in place by a nut (check vid ~9:05 min). Shaft can be lightly tapped with the gear on. vs. breaking the gear and pulling it from the throttle bottom.
Appreciate the feedback! Always trying to make these videos better for people!
🔧 keep it going! Killing it
This is awesome dude👍🏼
love these videos
this guy knows his stuff
Great video 👍
Thank you for this video! Very helpful!
Happy to help!
Mine just went bad would like to send them to get rebuilt
🔥
Would feel a little uncomfortable with the pin connection tbh. Butt I guess no issues yet?
Other than that nice work!
Nicely done
Is throttle body the same for S65?
Brad 2013 e93 M3
That I'm not sure about honestly. You can always compare part numbers
At what mileage do the throttle actuators fail mostly? My m5 got only 67,000 miles so should I worry about them yet?
I mean that's really low miles. From what I know, they tend to fail near 100k but if I were you, id buy the parts as soon as possible just have em ready at that point if you're trying to keep the car for a while
hey brother, would you rebuild mine if i mailed my actuators to you and paid you for the service?
Yeah no problem. Hit me up on my instagram @yevsbuilds
The problem is not only the gears !! It’s and the board!!
Yeah but since I've never seen this engine run before, I figured I'd start here with these
@@YEVSBUILDS yes but you did the half job if fails ! That will fail for sure you need to take them out again !!
The gears DO fail! I have several examples. They get worn and pointed on the output shaft gear causing slop the computer can recognize.
NOTE: From motor, through intermediate gear, and final gear on shaft, there is a great reduction at the motor (motor spins more than ten revs compared to output shaft). and slop can be detected by the throttle positions sensors.
Check M5board for details.
Yes, but if someone wants to do gears before they fail then that will also extend the circuit board life, the reason the circuit board fails is because of the extra bs it has to do when the gears start acting up, if you catch it early you might be able to save alot of money with only doing the gears.
Obviously the plastic gears get worn over time… but the main reason for the actuators failing is due to the circuit boards failing.
This throws the engine codes 2b15/2b16 and cause the car to go into limp mode
New actuators cost $800. This isn't worth it.