Hey everyone. The video turned out great! I had a great time with TriFecta shooting the gun and the video. It had around 3,000 bbs fired before that bucking issue came up. I'm getting a new bucking and will work on fixing the issue. The RDS was sighted too low and made hitting the targets a little harder than it should have been. Also, I had not yet tuned the sear set screws on the Kythera. I'm working on that and perfecting the airseal to improve consistency.
Welcome to HPA ownership, hopefully since the Kythera is mechanical it won't break every few game days if it does then do what I did when I got tired of the P* problems and buy a Wolverine Inferno Gen2 or if you like the mechanical aspect the Reaper Gen2 but I like the Spartan trigger board because you can program 3 or 5 round burst or semi lock it and it is the quietest HPA kit by far mine is quieter than my buddies Novritsch MK23 with the can on and mine without a foam filled can
All my shots are diving down pretty hard on my kythera, original hop up unit is still installed, psi between 80-100 doesn’t change anything, any thoughts?
With this gun build being custom, I would have stayed away from Ares had I known the differences with TM V2. I did get the other gearbox and lower to work, but it was not 100% fitting so I went back to the Ares.
Like Todd said, its all about the fine tuning with these engines. I used mine at a game for the first time today and while it was OK, right after I finished building it the night before, there was still a lot of tuning and adjustments that I needed to do. Alignment of the engine in the gearbox shell is the single biggest thing beyond getting the trigger sorted. that's just the first step. Aligning the body of the engine in the shell is another matter. A few layers of tape on the bottom of the Kythera was what did it for me. Getting that nozzle squarely in the hop unit is key! A standard AEG build is actually a sloppy thing when compared to a Kythera engine build.
You probably don’t need this info anymore, but it can be tuned to shoot pretty well stock, but if tuned improperly it’s kinda trash and will probably just stop working mid game.
Putting fiber glass and chicken wire in the suppressor, even if it's for airsoft can get you in a lot of trouble with the ATF. I would highly advise against it if you have dogs that you want to keep.
@@aden4149 In the US anything that lowers the volume of muzzle report by 1dB is considered by law a suppressor. That requires you have the tax stamp required for it to legally own and use it. Doesn't matter if it's a suppressor, oilcan or and airsoft mock suppressor.
@@Some.Canadian ummm. Then explain .177 caliber air rifles with suppressors from the factory? Airsoft suppressors are -14mm thread and inferior material. 5.56 are 1/2x28. You’re in no danger from the ATF with an airsoft suppressor.
ares guts, and as soon as he said 'maple leaf macaron' i cringed. the feedlip issue is always a result of the ares hop and macaron. Prommy purple bucking fits the ares hop chamber perfectly if you're looking at alternatives
The large tank in the backpack is compressed air, however check out the polarstar UGS which can use small compressed air bottles or co2 bottles in the stock of the gun.
![Airsoft - Polarstar Kythera V3 [French]](http://i.ytimg.com/vi/mxGDF_zSmfk/mqdefault.jpg)
![[4K] Watch SpaceX Catch A Starship Rocket From Space!!! #IFT5](http://i.ytimg.com/vi/pIKI7y3DTXk/mqdefault.jpg)
![COLOMBIA vs. CHILE [4-0] | RESUMEN | ELIMINATORIAS SUDAMERICANAS | FECHA 10](http://i.ytimg.com/vi/TDjN4W3yy1k/mqdefault.jpg)
I love the noise the targets make in slow motion. Thanks Todd for letting the guys review the Kythera!
Hey everyone. The video turned out great! I had a great time with TriFecta shooting the gun and the video. It had around 3,000 bbs fired before that bucking issue came up. I'm getting a new bucking and will work on fixing the issue. The RDS was sighted too low and made hitting the targets a little harder than it should have been. Also, I had not yet tuned the sear set screws on the Kythera. I'm working on that and perfecting the airseal to improve consistency.
love the hawk on the power line in the background
nice, we have a few of those around our back yard
That’s awesome guys. 👍👍👍
JP fell in love on the first date
Damn right 😍😂
Johnny Paulicelli aye brother, if you do a build please document you’re journey would love to see it 🙏
Marz Harris I absolutely will! I am planning on having it built by the end of the year at the latest, we’ll keep you updated 🤙🏻
Awesome review guys!!!
Nice gun. How much do those gun cost?
Kythera alone is $275. The gun as shown in the video...lots more than a stock gun. Join Patreon to see details.
Welcome to HPA ownership, hopefully since the Kythera is mechanical it won't break every few game days if it does then do what I did when I got tired of the P* problems and buy a Wolverine Inferno Gen2 or if you like the mechanical aspect the Reaper Gen2 but I like the Spartan trigger board because you can program 3 or 5 round burst or semi lock it and it is the quietest HPA kit by far mine is quieter than my buddies Novritsch MK23 with the can on and mine without a foam filled can
All my shots are diving down pretty hard on my kythera, original hop up unit is still installed, psi between 80-100 doesn’t change anything, any thoughts?
Look up the Polarstar facebook group. Post you question there. Will get plenty of opinions of what you did wrong.
@@toddr4923 get a new hop try the max hop
Great video guys
Ares guns are different shape gearbox. But you the gearbox in different receivers like apex elite forcé ect.
I have a gen1 ares m4a1 for ten years.
With this gun build being custom, I would have stayed away from Ares had I known the differences with TM V2. I did get the other gearbox and lower to work, but it was not 100% fitting so I went back to the Ares.
Awesome vid. Hearing Good and Bad about the new Kythera. Looks like Todd got a good one.
Thanks. I think it turned out well. With custom building anything, it takes time and patience to workout the issues and fine tune it.
Like Todd said, its all about the fine tuning with these engines. I used mine at a game for the first time today and while it was OK, right after I finished building it the night before, there was still a lot of tuning and adjustments that I needed to do. Alignment of the engine in the gearbox shell is the single biggest thing beyond getting the trigger sorted. that's just the first step. Aligning the body of the engine in the shell is another matter. A few layers of tape on the bottom of the Kythera was what did it for me. Getting that nozzle squarely in the hop unit is key!
A standard AEG build is actually a sloppy thing when compared to a Kythera engine build.
@@ChasWG how hard is it to align to the shell, just got one on order?
Always despised yet wanted hpa
How good is the engine complete stock? I just don’t trust myself enough to make modifications to it
You probably don’t need this info anymore, but it can be tuned to shoot pretty well stock, but if tuned improperly it’s kinda trash and will probably just stop working mid game.
4:31 I think he likes it 😂
They were all like that the first few shots! LOL
Putting fiber glass and chicken wire in the suppressor, even if it's for airsoft can get you in a lot of trouble with the ATF. I would highly advise against it if you have dogs that you want to keep.
just curious but why is it a bad thing in airsoft i can understand a real firearm but not airsoft
@@aden4149 In the US anything that lowers the volume of muzzle report by 1dB is considered by law a suppressor. That requires you have the tax stamp required for it to legally own and use it. Doesn't matter if it's a suppressor, oilcan or and airsoft mock suppressor.
@@Some.Canadian that’s only for firearms. That is not a firearm.
@@treybrasher434 Try telling that to the atf
@@Some.Canadian ummm. Then explain .177 caliber air rifles with suppressors from the factory? Airsoft suppressors are -14mm thread and inferior material. 5.56 are 1/2x28. You’re in no danger from the ATF with an airsoft suppressor.
Will a speed soft trigger fit and work
which trigger?
You guys should look at the Wolverine mtw
I've heard good things about wolverine
Colton Scalf I enjoy mine
I love my Kythera!!
How is the longer range accuracy? Is it very consistent
@@JoeMaxFpv With higher PSI, heavy BBs, good airseal - people have made great dmr builds. look at the P* FB page
It’s very consistent. I have mine in a krytac PDW. I need to tweak mine some more.
@@Beeehall stock pdw with just the engine in?
Not stock. I have a Maxx hopup with an rhop’d zci tight bore barrel. And a Speed trigger
ares guts, and as soon as he said 'maple leaf macaron' i cringed. the feedlip issue is always a result of the ares hop and macaron.
Prommy purple bucking fits the ares hop chamber perfectly if you're looking at alternatives
thanks for the info brother!
what brand of tracer unit?
g&g. see details here ruclips.net/video/Fo5mf-vzqL0/видео.html
So does it just use compressed air or c02?
The large tank in the backpack is compressed air, however check out the polarstar UGS which can use small compressed air bottles or co2 bottles in the stock of the gun.
Hmmmmm.... making me think about putting a hpa system in emg recce...
Same dude same!
Do it!!!!
I really love this engine. I would totally get it but I'm broke 💀.
Kythera sucks you would think is a easy setup but hell no this things are so bad to setup you better off buying a F2 or a jack
yeah, i'm surprised that there's not a gun that makes it easier to install this thing.