nvm im dumb if anyone has the same question, screw your empty tank onto the regulator then unscrew the green knob until you can see a thread, then you can fill your tank, once you have the tank filled screw the green knob back down until you can't see the thread(s) anymore, then you can go ahead and change the pressure on the regulator by pulling up on the black knob and twisting clockwise, once you have adjusted the pressure to what you want you can push the black knob back down. NOTE: To change the pressure on the regulator to increase it from ZERO you have to twist it THREE times in order for it to start increasing the pressure, when I first got mine and started trying to incease the pressure I thought it was broken but it was because I didn't twist it THREE times... Also: I would make sure you also purchase some extra O rings for this Regulator as theres a possibility they can dry and go bad after awhile. if you have any questions or need help, reply to this comment I'm pretty fast at replying and will most likely be able to help you Edit:2/26/23 I can't believe it's been nearly 2 years since i've written this comment haha, I hope it's been able to help. :)
@@kcdoesstuff1036 Hmmm I don't know about that I've taken my green knob off many times and it's always screwed back on, Is there something blocking it like something inside the green knob? If not try putting some pressure on it while trying to screw it on
@@kcdoesstuff1036 Awesome glad you got it to work! When you unscrew your tank from the reg it's probably just the friction that's causing the noise I wouldn't worry about it
hey amped what if i filled my tank before i unscrewed the green thing. i thought i did it all the way but turns out it’s wasn’t l. i’m i just screwed or what can i do
I was reading the site and it says it can only take 300 psi tanks, but I couldn’t fine any in 300 psi. Will it still work with a 3000 psi tank, or is this like a typo, bc I am very new to hpa and have no real idea what I’m doing
So i got this SLP rig setup for my jack, FCU is set to F1 and my settings are default when i got full auto the pressure doesnt hold it just drops to zero on semi its just fine i used the SLP rig on my F1 and it worked just fine
Can this unit, without the main tank side, be connected to a main regulator for a secondary, lower pressure line for another gun that needs to run at lower pressure?
Did you figure it out? I’m having same issue. Tank is full. But turning knob does nothing. Can’t get any gun pressure. I have a polarstar wall ornament. I’m close to throwing the tank and regulator in a dumpster and getting all new. Anyone have suggestion before I go postal.
Do you have a video about blocking or restricting the black knob ? I'm looking for ways to allow HPA guns on our airsoft field but I have to know if it is possible to lock those knobs to avoid cheaters on the game
Scyfox if they have that exact regulator in the video yes it has holes in the black knob which allow a ziptie to pass through. If you’re using the small zip ties and they player has this same reg then you’ll need to make a chain of little zip ties until you reach the metal part where the psi gauge is. And then wrap the ziptie chain around the unit itself. Takes about 3-4 small zip ties or one really long and skinny one. Make sure the zip ties are tight because if not the player can stretch the ziptie chain and still change the psi if they really wanted to
Would I be able to attach a 68/4500 tank with a Ninja Flex regulator set to 300psi output pressure? Or would I need a tank with a 4500 SLP regulator instead? I am trying to get away without having to purchase an SLP regulator by using the Ninja Flex regulator set down to 300psi output pressure. Thank you.
Hey I recently bought this and just put it on my tank and it was working great, however I was taking it off and when I was lowering the PSI on the regulator with the black knob, I accidentally pulled the knob off. I'm not sure how this happened or if its a major problem, but I was just wondering if anyone has any ideas of how to fix this. Thanks!
Could I take off the regulator if there is air in the tank still? Or if there is air in the tank I have to leave the regulator on until i use all the air?
what if you are running a ninja sl2 tank that comes with the stock tank regulator which puts out more than 350psi? do i need a new tank regulator or will I have to get a different regulator?
The threads on my sfr have been stripped( where you would adjust the psi) for a while and it's just getting worse. I'm almost at the point where I can't adjust the psi anymore. Any idea who to fix or better this problem?
Oh gese, that's no bueno. If those are stripped you will probably need a new body part to replace that. I would recommend reaching out to Redline Airsoft directly to see if they can provide you with the part that is stripped so you can swap it out. Probably the best solution for that. 8)
Thank you so much for this informative video. This has helped me with my issues with my reg and m134. Much respect from Oregon
thanks just bought one and had no clue what to do very helpful
Me watching this without buying one 🤣...(yet)
This helps out cause I have no clue what to do and how do I tell when I run out of air
1:13 Should I have my tank filled before I do this or after I put it on the tank should I go fill it
nvm im dumb if anyone has the same question, screw your empty tank onto the regulator then unscrew the green knob until you can see a thread, then you can fill your tank, once you have the tank filled screw the green knob back down until you can't see the thread(s) anymore, then you can go ahead and change the pressure on the regulator by pulling up on the black knob and twisting clockwise, once you have adjusted the pressure to what you want you can push the black knob back down.
NOTE: To change the pressure on the regulator to increase it from ZERO you have to twist it THREE times in order for it to start increasing the pressure, when I first got mine and started trying to incease the pressure I thought it was broken but it was because I didn't twist it THREE times...
Also: I would make sure you also purchase some extra O rings for this Regulator as theres a possibility they can dry and go bad after awhile.
if you have any questions or need help, reply to this comment I'm pretty fast at replying and will most likely be able to help you
Edit:2/26/23 I can't believe it's been nearly 2 years since i've written this comment haha, I hope it's been able to help. :)
@@Slicks_16 I accidently took the green knob off, any help on how it comes back on? I tried to normally screw it in but it doesnt screw on
@@kcdoesstuff1036 Hmmm I don't know about that I've taken my green knob off many times and it's always screwed back on, Is there something blocking it like something inside the green knob? If not try putting some pressure on it while trying to screw it on
@@Slicks_16 gotcha man, I got it to work, I was also wondering why when I take my tank off the reg, I hear a slight grinding noise
@@kcdoesstuff1036 Awesome glad you got it to work! When you unscrew your tank from the reg it's probably just the friction that's causing the noise I wouldn't worry about it
hey amped what if i filled my tank before i unscrewed the green thing. i thought i did it all the way but turns out it’s wasn’t l. i’m i just screwed or what can i do
Can I get this for any paintball tank?
I was reading the site and it says it can only take 300 psi tanks, but I couldn’t fine any in 300 psi. Will it still work with a 3000 psi tank, or is this like a typo, bc I am very new to hpa and have no real idea what I’m doing
yes it will work with a 3000 psi tank it just has to be slp and what they mean by 300 psi is the output pressure of the tank
why didnt u have to turn the green knob loose before taking off the tank. u only have to adjust it when u connect a tank?
So i got this SLP rig setup for my jack, FCU is set to F1 and my settings are default when i got full auto the pressure doesnt hold it just drops to zero on semi its just fine
i used the SLP rig on my F1 and it worked just fine
Can this unit, without the main tank side, be connected to a main regulator for a secondary, lower pressure line for another gun that needs to run at lower pressure?
I was twisting the green thing like it said in the video and it came off and I can’t put it back on how do I put it back on plz help
Nvm I’m kind dumb I just got it yesterday
@@alexanderrivera3674how do you put it back on? I'm having the same problem
I put it on my tank and had it filled. Cant get pressure to the regulator. Turning the black knob does nothing. It’s all brand new.
This regulator sucks the adjustment knob always breaks bro I’ve had 2 of them and 2 of my friends as well all broken adjustment knob .
When adjusting the psi it just says it on the reader below right?
The green is not screwing on
how increase power fro, 110 psi to 160?
I've been having problems getting pressure to the regulator, and I just barely bought the unit. If anyone can help that would be awesome
Guess you could say it's not AirTight
@@andrewlandrau3425 omg 😂
Did you figure it out? I’m having same issue. Tank is full. But turning knob does nothing. Can’t get any gun pressure. I have a polarstar wall ornament. I’m close to throwing the tank and regulator in a dumpster and getting all new. Anyone have suggestion before I go postal.
@@JoeMaxFpv visit r/airsoft on Reddit , they’re super smart when it comes to little issues
Do you have a video about blocking or restricting the black knob ?
I'm looking for ways to allow HPA guns on our airsoft field but I have to know if it is possible to lock those knobs to avoid cheaters on the game
Scyfox if they have that exact regulator in the video yes it has holes in the black knob which allow a ziptie to pass through. If you’re using the small zip ties and they player has this same reg then you’ll need to make a chain of little zip ties until you reach the metal part where the psi gauge is. And then wrap the ziptie chain around the unit itself. Takes about 3-4 small zip ties or one really long and skinny one. Make sure the zip ties are tight because if not the player can stretch the ziptie chain and still change the psi if they really wanted to
My dial is stuck what do i do it came stuck out of the box the black dial not the green one
Would I be able to attach a 68/4500 tank with a Ninja Flex regulator set to 300psi output pressure? Or would I need a tank with a 4500 SLP regulator instead? I am trying to get away without having to purchase an SLP regulator by using the Ninja Flex regulator set down to 300psi output pressure. Thank you.
I'm having issues with my regulator. It wont go above 110 psi. The black knob will spin as far as it can but wont increase output
Send us an email at "Sales@ampedairsoft.com" and we can get you all taken care of!
Did you ever get this solved ? I have the same problem.
@@AmpedAirsoft can I just put a paintball hpa tank on mine? Also can I just connect the end that goes to the gun on a cqb Russian hpa valve?
My regulator is stuck at 80? But it maxes out at 160 it says??? HELP I JUST GOT ITTT😂😂
are you think about selling different color green nobs/valve?
Nice vid , very helpful
Awesome. Thanks!
2:56 does anyone know how to attatch it mine fell off and I lost it on the field
Hey I recently bought this and just put it on my tank and it was working great, however I was taking it off and when I was lowering the PSI on the regulator with the black knob, I accidentally pulled the knob off. I'm not sure how this happened or if its a major problem, but I was just wondering if anyone has any ideas of how to fix this. Thanks!
Nevermind, figured out how to fix it. Really easy fix, I'm a little stupid at times 😅
@@aveadonat9378so is it supposed to come off? I took mine off and I haven’t shot it yet so I don’t know how to adjust it.
@@DYNAM0-504 for maintenance purposes it comes off but if you wanna adjust psi you need it on
@@aveadonat9378 how do I determine what the psi is adjusted to?
@@DYNAM0-504 there's a gauge that tells you what ur psi is
How would I set my pew to 350 fps with this regulator?
you regulate the air
Does it have to be a Slp tank
Yes
yes
Could I take off the regulator if there is air in the tank still? Or if there is air in the tank I have to leave the regulator on until i use all the air?
you can take off the reg at any time just as long as you turn off the valve on the reg
I have a hpa tank with hpa regulator.. if i use it.. will it broke?
Wdym, an HPA tank with this regulator will work fine?
@@Fir3bolt42 noo.. i have ninja tank with ninja tank regulator.. its say the output is 800 psi.. if i use this hpa slp regulator, will it broke?
@@indonesianairsoft4429 it has a max output of 800, the my tank as a max output of 1800 and I have been using this perfectly
@@Fir3bolt42 ok.. thank you so much 🙏🙏
what if you are running a ninja sl2 tank that comes with the stock tank regulator which puts out more than 350psi? do i need a new tank regulator or will I have to get a different regulator?
Thanks for the helpful video
how many shots will i get out of my Ninja 62/3000 Aluminum Tank and my regulator is at 90 psi?
around 2,066
Does the kit come with a tank?
No you have to purchase separately
Can this work on a scorpion evo?
If it’s HPA yes
audio is a bit low!!!! hard to hear him sometimes
The amped line connectes directly to a TAPP HiCapa adapter, right? So no need for the gun-side connector and macro line?
Correct. The female fitting on the line will connect directly to your TAPP Hicapa adapter!
@@AmpedAirsoft thanks!
The threads on my sfr have been stripped( where you would adjust the psi) for a while and it's just getting worse. I'm almost at the point where I can't adjust the psi anymore. Any idea who to fix or better this problem?
Oh gese, that's no bueno. If those are stripped you will probably need a new body part to replace that. I would recommend reaching out to Redline Airsoft directly to see if they can provide you with the part that is stripped so you can swap it out. Probably the best solution for that. 8)
@@AmpedAirsoft Ok thank you!
@@tylerdonovan5314 No problemo!
Way to big