I’ve been watching a lot of videos for ideas, redoing my squire tele, I really like this longer explanation. I see comments about the wires, I thought it was a cool extra insurance you did for the grounding. Thank you sir for a great video on shielding
excellent video! the wire under the tape is genius. I got the same tape for my 2007 MIJ tele which comes with no shielding at all, will be following your tutorial for it.
Thanks for commenting! It is a bit redundant. For me, I like the idea in having a direct grounding in addition to the shielding but of course it should still be fine doing without.
The tape I got was only 15mm wide, the only size available to me with conductive adhesive. I cut out a paper template to fit the base of the cavities plus about 1/8" larger all round, then applied the tape to the paper. Much easier to get into the cavities. Tape on the side walls holds the bottom template/tape in place. Because the adhesive is conductive, (only buy this type) you can apply small pieces at a time overlapping each piece, no need to try to do the walls of the cavity in one long strip. Test for continuity with a cheap (few $$) multi-meter. Some adverts say "conductive adhesive" but it isn't. That is why you must test for continuity. No continuity-no shielding, as the electrical interference needs to be led away to earth. Tearing rather than cutting the tape usually gives you an easier edge to peel the tape off the backing paper.
All excellent ideas and suggestions! One of the reasons I love RUclips!! Provides all of us with the ability to share experiences and ways to improve quality and efficiency!! Thank You so much in taking the time in watching and sharing your experiences and suggestions! Really means a lot! Thank You!
Thank you for putting this video together! The wires bridging the cavities is a cool idea. When you put all the guts back into that guitar did you have to ground all that shielding somewhere? If so where did you choose? Also would you bother shielding the hole that connects to control cavity to the guitar jack? thx!
Thank you so much for watching and commenting and I hope it proved to be helpful at some level! I do advise searching and watching other videos on the subject in that I did not go into detail on the purpose of shielding and how it works. For shielding to work, it must be in contact with ground. Each application is different depending upon your particular instrument configuration. In this particular case, the volume pot housing is in contact with the foil, so a ground jumper to the foil was not necessary. I did not bother attempting to shield the control cavity to the guitar jack because how tight it was and I have not experienced any adverse effects as a result. However, if you prefer to shield the jack cavity, I'm certain it won't hurt anything. Again, avail yourself to other instructional videos out there. You might consider using shielding paint in the jack cavity as a possible alternative. I hope this helps! Good Luck! Would love to hear back how your project turns out!
Thanks for the detailed video. I’m wondering if the wire between cavities is needed, since they’re connected by the pick guard and the overhanging tape?
@@WEdHarris Thank you for your response, and for making this video. I ended up doing it the way you did with the wire, copper tape, and tabs on top of the body for the pickguard and have continuity between all the cavities. Next I'm replacing the pickups with Seymour Duncan La Brea pickups, replacing the plastic nut with a bone nut, and installing an Emerson 4 way control plate assembly using cloth shielded wiring. 👍🏻
Roll the shielding foil over the edges of each opening slightly so that it can make contact with the shielded pickguard and then it isn't necessary to ground with wires.
Great video Ed,, thank you!! I recently bought a Telecaster from a friend. It's a 2012 model that's made in Mexico. Is this something I should do or does the manufacturer do a well enough job to not worry about it? Also, the tuning machines or a little "wonky" and my friend said they were. I'm conflicted as to if I should go originals or the more expensive upgrade type tuners! It's a great sounding guitar but won't stay in tune very well.
You are so very welcome David and Thanks so much for watching and commenting! Yes, I would definitely check to evaluate the shielding (if any) you currently have and redo with copper adhesive shielding as I've done here. The results are incredible (super quiet). I have other videos upcoming including wiring and complete set-up on this project. The guitar sounds great which I will also demonstrate at the end. I would also upgrade to higher quality tuning machines as well for sure. Nothing is more frustrating than an instrument that won't stay in tune. It would be well worth the investment.
@@WEdHarris Thank you so much and I'll take your advice!! I have other questions concerning a mountain dulcimer that you probably can help with but I'll save that for later!
Great question and idea! In this particular application I left a wire "tang" overhang which I mentioned for the bridge as well as shielded the underside of the pick guard. Everything had been tested for continuity and the end result was acceptable. Your idea is a very good one and certainly another option as well!! Thanks so much for the input!
Thanks so much for your question! My apology for such a late reply. I used wire for my connection that ran through the channel as opposed to relying on continuity via the underside of the shielded pickguard. The main objective of course is continuity so if there is an opportunity to streamline continuity without compromising then go for it. I just felt the wire would provide a more definitive connection in this instance. Basically there are no steadfast rules here as long as the basic principles are met. Thanks Again! Great question!
Hey Chris, This vid was intended to show some technique in how to shield the cavities using copper tape. There are plenty of excellent vids out there that go into the specifics on the purpose of shielding and it's benefits. Basically, the idea behind shielding is to enclose the electronics in a "cage" which helps to reject stray radio frequency interference.
Remember that you need the help, not him. It’s not his obligation to help exactly how you need because your lack of ability to do some research beyond a video. Be nicer.
Great instructional video. No lame introduction branding, and no terrible loud music, so you can't be heard. Thank you
Thank You so much! I'm no expert but I hope the video proved to be of some value!
This was a great video. And it looks like you did an excellent job. Now.......................gotta cut open my package of copper tape
Thanks so much! I hope it proved somewhat helpful!
I’ve been watching a lot of videos for ideas, redoing my squire tele, I really like this longer explanation. I see comments about the wires, I thought it was a cool extra insurance you did for the grounding. Thank you sir for a great video on shielding
Thank you for watching and commenting! I hoped the video proved helpful!
excellent video! the wire under the tape is genius. I got the same tape for my 2007 MIJ tele which comes with no shielding at all, will be following your tutorial for it.
Thanks so much! I hope it helps!
Nice video, once you’ve connected all the parts like a faraday cage, is still needed the ground wire from bridge to volume pot? Many thanks
Thanks for commenting! It is a bit redundant. For me, I like the idea in having a direct grounding in addition to the shielding but of course it should still be fine doing without.
The tape I got was only 15mm wide, the only size available to me with conductive adhesive. I cut out a paper template to fit the base of the cavities plus about 1/8" larger all round, then applied the tape to the paper. Much easier to get into the cavities. Tape on the side walls holds the bottom template/tape in place. Because the adhesive is conductive, (only buy this type) you can apply small pieces at a time overlapping each piece, no need to try to do the walls of the cavity in one long strip. Test for continuity with a cheap (few $$) multi-meter. Some adverts say "conductive adhesive" but it isn't. That is why you must test for continuity. No continuity-no shielding, as the electrical interference needs to be led away to earth.
Tearing rather than cutting the tape usually gives you an easier edge to peel the tape off the backing paper.
All excellent ideas and suggestions! One of the reasons I love RUclips!! Provides all of us with the ability to share experiences and ways to improve quality and efficiency!! Thank You so much in taking the time in watching and sharing your experiences and suggestions! Really means a lot! Thank You!
Thank you for putting this video together! The wires bridging the cavities is a cool idea. When you put all the guts back into that guitar did you have to ground all that shielding somewhere? If so where did you choose? Also would you bother shielding the hole that connects to control cavity to the guitar jack? thx!
Thank you so much for watching and commenting and I hope it proved to be helpful at some level! I do advise searching and watching other videos on the subject in that I did not go into detail on the purpose of shielding and how it works. For shielding to work, it must be in contact with ground. Each application is different depending upon your particular instrument configuration. In this particular case, the volume pot housing is in contact with the foil, so a ground jumper to the foil was not necessary. I did not bother attempting to shield the control cavity to the guitar jack because how tight it was and I have not experienced any adverse effects as a result. However, if you prefer to shield the jack cavity, I'm certain it won't hurt anything. Again, avail yourself to other instructional videos out there. You might consider using shielding paint in the jack cavity as a possible alternative. I hope this helps! Good Luck! Would love to hear back how your project turns out!
Thanks for the detailed video. I’m wondering if the wire between cavities is needed, since they’re connected by the pick guard and the overhanging tape?
That's a great question! If you try it that way, please be sure and let me know how it turns out!
@@WEdHarrisno wire needed. The shielded pick guard connects via the overhang, I tested with a meter.
@@learningguitar7948 Excellent! Thanks so much for following up! So glad it worked out!
Instead of using wire to ground the cavities would using tape to connect the cavities on top of the body work?
Oh yes, absolutely it should work! Let me know how it turns out if you are currently working on a similar project!
@@WEdHarris Thank you for your response, and for making this video. I ended up doing it the way you did with the wire, copper tape, and tabs on top of the body for the pickguard and have continuity between all the cavities. Next I'm replacing the pickups with Seymour Duncan La Brea pickups, replacing the plastic nut with a bone nut, and installing an Emerson 4 way control plate assembly using cloth shielded wiring. 👍🏻
@@Shadowman-1960 Sounds awesome! I can’t wait to hear how it turns out for you!
Roll the shielding foil over the edges of each opening slightly so that it can make contact with the shielded pickguard and then it isn't necessary to ground with wires.
Great video Ed,, thank you!! I recently bought a Telecaster from a friend. It's a 2012 model that's made in Mexico. Is this something I should do or does the manufacturer do a well enough job to not worry about it? Also, the tuning machines or a little "wonky" and my friend said they were. I'm conflicted as to if I should go originals or the more expensive upgrade type tuners! It's a great sounding guitar but won't stay in tune very well.
You are so very welcome David and Thanks so much for watching and commenting! Yes, I would definitely check to evaluate the shielding (if any) you currently have and redo with copper adhesive shielding as I've done here. The results are incredible (super quiet). I have other videos upcoming including wiring and complete set-up on this project. The guitar sounds great which I will also demonstrate at the end. I would also upgrade to higher quality tuning machines as well for sure. Nothing is more frustrating than an instrument that won't stay in tune. It would be well worth the investment.
@@WEdHarris Thank you so much and I'll take your advice!! I have other questions concerning a mountain dulcimer that you probably can help with but I'll save that for later!
How did the ground under the tape turn out? I have some ordered
Parabéns...
Muito Obrigaod!!
How many shielding videos are there on youtube? Over 100 I bet. Not sure why.
I often wonder how many musicians there are in the process or contemplating undertaking such projects... LOL
Ed, why no overhang copper for the bridge?
Great question and idea! In this particular application I left a wire "tang" overhang which I mentioned for the bridge as well as shielded the underside of the pick guard. Everything had been tested for continuity and the end result was acceptable. Your idea is a very good one and certainly another option as well!! Thanks so much for the input!
do i need to add the wire ? if so whats the purpose ? can i just add the tape without the wire ?
Thanks so much for your question! My apology for such a late reply. I used wire for my connection that ran through the channel as opposed to relying on continuity via the underside of the shielded pickguard. The main objective of course is continuity so if there is an opportunity to streamline continuity without compromising then go for it. I just felt the wire would provide a more definitive connection in this instance. Basically there are no steadfast rules here as long as the basic principles are met. Thanks Again! Great question!
So you’ll show us how to stick copper tape to the guitar but you won’t get into what it’s actually doing for you. Thanks. Great help
Hey Chris, This vid was intended to show some technique in how to shield the cavities using copper tape. There are plenty of excellent vids out there that go into the specifics on the purpose of shielding and it's benefits. Basically, the idea behind shielding is to enclose the electronics in a "cage" which helps to reject stray radio frequency interference.
Remember that you need the help, not him. It’s not his obligation to help exactly how you need because your lack of ability to do some research beyond a video. Be nicer.
@@WEdHarrisI think this a great video. I actually never thought about the wire concept! That’s a great idea to insure continuity!
It's a Faraday cage preventing unwanted interference, all you need to know.