Hi albert I came across this channel because I am doing the exact same thing just with the original literadio 2 and I have bought the erls board and the gimbals for it just need to find the battery for it do you know where I can find a battery with 1.25 connector I have looked everywhere and can’t find any
In a nutshell ELRS is 10X better than the old style protocols. However, if you want the TLDR answer, there's a whole playlist of videos about ELRS in the video description.
Also does this flash give the radio ability to bind with elrs, or is this a third version, betafpv lite, betafpv lite 2 se, betafpv lite elrs? Thanks for the work.
You probably don't have the correct drivers installed or you connected it with the power on. It needs to be OFF. If you need the drivers, go here... www.st.com/en/development-tools/stsw-stm32102.html
I have the same problem! When I connect RC to pc the lighter on controller is off and I can't change setting on RC. But in setup mode controller connects perfect and I can update firmware. I didin't find how to fix it( (RC was a part of cetus pro kit if it is necessary)
my lite radio 2 se elrs won't work. when i arm it seems to work until I move the throttle up it just ramps up and won't respond until I disarm does anyone also have this problem or has a way to fix it
Hi, nice video! Do you know how do i add dead zone, please? My BetaFPV Radio is very bad and it has some gap beetwen 0 and -10 to left on right gimbal, so id like to add a deadzonem but i couldnt find... what i could find is the offset, but it just add or remove, i would like to kill these interval.. Thanks!
Hi, can you help me bind my control? A bought the same control BETAPFV 2 SE (internal RF: ExpressLRS 2.4GHz) with receiver Nano ELRS Mini 2.4ghz rx sx1280.
ah.. I can't get the com port to show up with the controller. Works with flight controllers. This is where my issue is. Can I send you my literadio board and have you flash it for me? lol
@@AlbertKimTV yessir. Zadig and driver fixer is not working. I remember a while back on a cetus pro I had to literally use a different computer. I may try grabbing an old lap top and trying again. Of course now the controller is refusing to go into firmware flashing mode again. Maybe I should just return the gimbals lol
I had a question I followed your video everything worked out but I’m trying to bind my meteor65 to the controller I just don’t know how. I did download express lrs configurator. Also, I created a bind phrase on the controller. I’m not sure if I’m even able to do it with this board. I’m trying to connect through Wi-Fi. Do you have any suggestions?
If you watched the video at 6:40, it shows how to add a bind phrase to the controller assuming you have updated the firmware as shown in the video. That bind phrase needs to match the one you put into the meteor65. I'm not sure which version you have but there's a few different ways to add the bind phrase. Please read the documentation on the expresslrs.org website as it's way too much to copy/paste here. Lastly, the version of firmware must be the same major version on the controller and receiver. The firmware in this video will be on 2.x. The firmware on the drone also needs to match otherwise the bind won't work.
@max max how far do you need to go? I think at 100mW even with a junk antenna you can go many kilometers away. If anyone else is interested in a range test, please reply to this comment.
@@AlbertKimTV Hey, since sma pigtail mod is super easy to do and original antenna is a patch antenna (why patch !?) everyone should know there is possibility to easily upgrade this radio :P i am waiting for my radio to arrive and I'll test both of those antennas but i guess the omnidirectional will give more stable and overall better connection than patch
LiteRadio 2 SE ELRS Edition
BF - bit.ly/39RKrEw
BG - bit.ly/3EAOEdz
ExpressLRS Transmitter Board - bit.ly/39Jilfd
ExpressLRS Playlist - bit.ly/370CYSH
LiteRadio 2 SE Review - ruclips.net/video/7loW4m-5Z6M/видео.html
🙏 Please support with a 👍 and don’t forget to hit the 🔔 thanks!
💲 If you enjoy my content, please support my channel through these links
Patreon - www.patreon.com/albertkim
Amazon - amzn.to/3zq84zp
RaceDayQuads - bit.ly/RDQ-BF
Pyrodrone - bit.ly/3Bfo3BP
Banggood - bit.ly/3imXlie
Airblade - bit.ly/3ilYVRr
NewBeeDrone - bit.ly/3BhFdPu
Makerfire - bit.ly/2VGI3Kg
Aliexpress - bit.ly/3im17IF
XT-XINTE - bit.ly/3inl7KQ
HGLRC - bit.ly/HGLRCBF
RekonFPV - bit.ly/3BagxIq
BETAFPV - bit.ly/2Ui1Pic
Diatone - bit.ly/3z9y01W
Flywoo - bit.ly/3exnkSJ
Caddx - bit.ly/3etIVLN
Insta360 - bit.ly/2VRDNe5
PayPal - paypal.me/marblekit
👉 Old gear for sale here - bit.ly/AlbertGearFS
👉 Follow me on social
🐤 twitter.com/albertkim
📸 instagram.com/marblekit/
😀 facebook.com/albertkimrc
Thank you very much, the literadio 2 was not able to work with Windows 11 and thanks to your video and updating the firmware, it now works
Glad it helped
Thanks Albert !
I received my LiteRadio 2 SE upgrade board yesterday & will install it this weekend - this helps a lot !
Glad it helped!
Very informative tutorial on flashing the betaFPV lite radio. Seems reasonably easy to do. Happy flying everyone. 🤓
Glad it was helpful!
Thanks for the tutorial, keep up the good work!
Thanks, will do!
Thanks . Always helpful and clear .
You are welcome!
Mille grazie.....❤🧡💛
Awesome, Albert! Thanks for the tutorial! 😃
Stay safe there with your family! 🖖😊
Thanks, you too!
Hi albert I came across this channel because I am doing the exact same thing just with the original literadio 2 and I have bought the erls board and the gimbals for it just need to find the battery for it do you know where I can find a battery with 1.25 connector I have looked everywhere and can’t find any
What is the advantage of elrs compared to the previous protocol in the radiolite se betafpv?
What is the output? 100mw?
In a nutshell ELRS is 10X better than the old style protocols. However, if you want the TLDR answer, there's a whole playlist of videos about ELRS in the video description.
Also does this flash give the radio ability to bind with elrs, or is this a third version, betafpv lite, betafpv lite 2 se, betafpv lite elrs? Thanks for the work.
👍⭐⭐⭐
⭐
What do I do if I press connect rc and it’s doin nothing
You probably don't have the correct drivers installed or you connected it with the power on. It needs to be OFF. If you need the drivers, go here... www.st.com/en/development-tools/stsw-stm32102.html
I have the same problem! When I connect RC to pc the lighter on controller is off and I can't change setting on RC. But in setup mode controller connects perfect and I can update firmware. I didin't find how to fix it( (RC was a part of cetus pro kit if it is necessary)
@@psih747 did you fix that ? If yes how
Hi, thank you for the video, is it possible to upgrade to ELRS 3.0? thanks in advance
Not available yet. I don't know if they will upgrade it to 3.0 or not. I would ask BETAFPV directly.
my lite radio 2 se elrs won't work. when i arm it seems to work until I move the throttle up it just ramps up and won't respond until I disarm does anyone also have this problem or has a way to fix it
Check how the gimbals behave in Betaflight. Your throttle gimbal might be defective.
I will try thanks
Calibrate gimbals :) helped me ...
Hi, nice video!
Do you know how do i add dead zone, please? My BetaFPV Radio is very bad and it has some gap beetwen 0 and -10 to left on right gimbal, so id like to add a deadzonem but i couldnt find... what i could find is the offset, but it just add or remove, i would like to kill these interval.. Thanks!
You need to update to the latest configurator and radio firmware you can download at this link... github.com/BETAFPV/BETAFPV_Configurator/releases
I have the newest firmware but i cant figure out which elrs version it is. Is there a way to flash other versions?
On the product page there are instructions on how to update the firmware with their configurator.
Hi, can you help me bind my control? A bought the same control BETAPFV 2 SE (internal RF: ExpressLRS 2.4GHz) with receiver Nano ELRS Mini 2.4ghz rx sx1280.
I made a video on this already... ruclips.net/video/_NyTFQ0G87Y/видео.html
@@AlbertKimTV i saw, the problem is, the firmware, i dont know, has no connection. I'm trying this for 4 months and no success. I'm into crazing
can i update the firmware of my literadio 2se to 2.0 if its the frisky version, it came with the cetus fpv kit
Frsky and ELRS are incompatible.
@@AlbertKimTV thanks, the 2.0 firmware is only for the elrs?
ah.. I can't get the com port to show up with the controller. Works with flight controllers. This is where my issue is. Can I send you my literadio board and have you flash it for me? lol
Sounds like a USB driver issue. Have you tried ZADIG? Try this video... ruclips.net/video/0mrJG7AOmRI/видео.html
@@AlbertKimTV yessir. Zadig and driver fixer is not working. I remember a while back on a cetus pro I had to literally use a different computer. I may try grabbing an old lap top and trying again. Of course now the controller is refusing to go into firmware flashing mode again. Maybe I should just return the gimbals lol
I had a question I followed your video everything worked out but I’m trying to bind my meteor65 to the controller I just don’t know how. I did download express lrs configurator. Also, I created a bind phrase on the controller. I’m not sure if I’m even able to do it with this board. I’m trying to connect through Wi-Fi. Do you have any suggestions?
If you watched the video at 6:40, it shows how to add a bind phrase to the controller assuming you have updated the firmware as shown in the video. That bind phrase needs to match the one you put into the meteor65. I'm not sure which version you have but there's a few different ways to add the bind phrase. Please read the documentation on the expresslrs.org website as it's way too much to copy/paste here. Lastly, the version of firmware must be the same major version on the controller and receiver. The firmware in this video will be on 2.x. The firmware on the drone also needs to match otherwise the bind won't work.
Thank you for the advice my meteor 65 is running on firmware 3.3.0 and my receiver is running on firmware 1.0.1
How about upgrading antenna in this radio ? Should be easy to place there router-like 2.4ghz dipole ?:P or just sma and connect anything you like
There's already a lot of videos on how to do that. Don't waste you time, Albert
@@925fpv well , is there any video how it affected elrs literadio 2 se range ?
@max max how far do you need to go? I think at 100mW even with a junk antenna you can go many kilometers away. If anyone else is interested in a range test, please reply to this comment.
@@AlbertKimTV Hey, since sma pigtail mod is super easy to do and original antenna is a patch antenna (why patch !?) everyone should know there is possibility to easily upgrade this radio :P i am waiting for my radio to arrive and I'll test both of those antennas but i guess the omnidirectional will give more stable and overall better connection than patch
@@maxmax-xx7nw The patch works fine as long as you are pointing it in the direction of the quad. Otherwise, it's worse.
somebody knows how to connect it with Android?
Why? For a simulator? It should just show up as a USB joystick but your phone needs to support UTG USB mode which many Android phones DO NOT.
@@AlbertKimTV Yes, for simulator, my phone support OTG, I can connect mouse and keyboard but not this controller
I do not see the binding phrase option
Watch about 6 minutes of the video, there is an option to enable in the configurator. Also, firmware needs to be updated first to enable this.
your video showed me exactly how to do it. 👍 I figured out the issue thank you. I enjoyed watching your videos and thank you for replying also.
literadio - 3 spoiler :)
🤣
I think the gain on your mic is up too high, brother. I hear the audio peaking on almost every video these days. Hope this helps 🤙
Thanks for the tip