Stop bad welding !!! The best technique for position 2f
HTML-код
- Опубликовано: 16 май 2023
- #arcwelding
#weldingforbeginners
#weldingtipsandtricks
#welding #weld #weldingforbeginners #weldingtechniques #weldingtipsandtricks #arcwelding
Stop bad welding !!! The best technique for position 2f
Before you start welding, you must clean the material first.
Great point!
I thought that looked too rusty
Not correct
mmaw will just weld through rust and milscale. gmaw or gtaw, you definitely need to grind milscale and rust.
Btw, this video is stupid. He sets the welder low and purposefully runs a shit weld, and then turns the welder up and adds a weave to his weld to make it seem like he's a genius.
This helped me out a ton!! Just seeing this video once seriously improved how I welded!!
It's a pleasure to be able to help you with this video😍
I’m a skilled coded welder and you don’t need to weave every fillet weld ! If you’re having problems with undercut, slag holes & unstraight runs then try practicing more and even try a different brand of welding electrode.
The weld depends on the requested leg length of the fillet so a small thin run has to be done on certain welds
Thank you for your kind comment
what rod is best for 2f
This worth a subscription, I got a hardtime to do a fillet and I hope that watching your videos can help me bro
Thank you dear brother
Excelent.
Thanks For Vedio, From Bangladesh
Welcome!
im going to start learning welding starting next month🤟🏻
Good luck!
Salam satu hobi dari bandung
Thank yo so much sir
Most welcome
Good job brother! 👏👏👏👏
Thank you 🙌
Tehnik yg bagus sob,selamat beraktifitas dan sukses slalu
Thanks bro🌹
I m walder from pakistan
good job bro❤❤❤
Thanks 🔥
So your technique was to follow established welding procedures... cleaning the metal, using the proper amperage, and traveling slow enough to allow proper weld penetration.
Отлично👍👍
Thanks 🤗
สุดยอด❤❤❤❤
♥️
The volt been bin automatic higer when you turn up the ampere if you welding with sticks,need not do pendle up and down like the doing here , and remember good negative connection on the plate or the thar you welding on
real beldar bahi🧿♥️📍🥰
😍🥰
Steel roads h kya yehh
Very nice 👍👍
Thank you 👍
❤
Wish you showed what size and type of rod
В конце нужно точку ставить, а не просто убирать электрод!!!
Отлично
Thanks
Come and see...good job Bro..👍❤️
Thanks ✌️
@@weldingtricks2023 you are welcome..👍
Nice😊
Thanks 😊
Bom trabalho rapaziada escrevendo de Angola Luanda
Thanks for watching
He Sad, good job guy, writeing from Angola Luanda. I too speak portuguese from Brazil and Loved your video.
Great skill bro.
Thanks bro🥰
Nice
Thanks
There’s a bunch of porosity
고맙습니다.
🥰😍
안녕하십니까❤❤❤
Good
Thanks
Grazie
Thank you too 🥰
👍👍
👍🥰🤗
❤❤❤❤❤❤
♥️👍🙏
The Best!
Thanks bro🤗😍
Правильно, токурде добавил. Варите на больших токах.
Bahi jan wiza mil jye ga
❤❤❤❤❤
🤗😍
جيد
👍
Im wilder from morooco
👍
สุดยอดครับ
❤️😍
Bang tolong ukuran kawatnya berapa mm?
3mm
You don't need to wave it
I think the amperage should have been a little lower. Made a little dent in the material
👍
Шов должен быть толщиной наименьшей толщины металла
👍
Слышь, бл, Герасим, люди ЗВУК давно придумали! На крайняк, субтитры. Век НЕМОГО КИНО ушёл! 😆😆😆
Сварка ишлар борми окалар
👍
🇲🇦✌️❤️
👍👍👍
.
ভাই আমি মিগ ওয়ালডার আপনার কাছে লোক লাগবে
👍
Ganon pala mag welding. Ang hirap pala
Very easy 👍
왜 첫째 방법으로 하면 안되는가?
which way
Хуршеди аблах
The method that you are doing almost looks like you are stitching, and open wound with a needle and thread.
Thanks for the tip!
@@weldingtricks2023😊
Stop that side-to-side shit and set your welding machine properly and use the right thickness electrode
👍👍
🤗😍
Good
Thanks