DIY homemade laptop pc custom plywood portable case
HTML-код
- Опубликовано: 21 авг 2024
- Hello everyone!
In this video i'll show you a little video of my homemade custom pc laptop style case.
When i became frustrated with lack of standarized components in laptops and i needed a PC with portability in mind which a desktop wouldn't allow i decided to build this computer.
I used mostly laying around components and some i needed to buy.
Motherboard, CPU, RAM and monitor i bought earlier for something else but i decided not to do it and ended up not using those stuff then.
It was not intended to be a laptop replacement but rather a little more portable desktop.
Case features a simple storage compartment for small headphones, wireless mouse and power cable.
Also it is equipped with hot-swap 2.5" hdd bay.
I used stock cooler because it has quite low height and got it with the cpu.
Hinges allow to move the lid laptop style.
Monitor accepts 12v, i tried to wire it to the molex 12v connector but it had weird artifacts and i turned it off fast to avoid potential damage.
If i had succeeded it would have simplified construction considerably. But i did not want to take unnecessary risks.
some of the components used:
motherboard: msi h110m pro-VD
cpu: intel pentium G4560 (i might upgrade it to something more powerful soon, for work and light games its more than enough)
RAM: single adata 8gb 2400 ddr4 (for use with iGPU dual channel is recommended but i intend to add dedicated gpu later, i'm waiting for a riser shipment)
psu: chieftec gpf-350p (350w, tfx)
amplifier: pam8610 (wiring diagram for power and speakers included in video)
speakers: i had these laying around salvaged from old crt TV)
When connecting HDD i could have used separate power and data cables because it is screwed to the case anyway, but i did not think about it then. Combo cable is needed for swap bay construction cause it simplifies its construction considerably.
I used plywood for body because i had some around and it's not that expensive and quite durable and lightweight for its size.
I know that a steel or even plexiglass would be better since wood is quite bad at dissipating heat and blocks wi-fi signals (that's why antenna is outside of case).
And some shielding inside a case and at the back would help but this build was intended as a rather quick prototype to use some unused stuff and check if the size isn't too large etc.
Speakers should have boxes to sound better, i might incorporate them in more refined version of the case.
There's no noticeable noise from speakers, but it might happen in an unshielded case. You should avoid ground loops, use shielded wires and so on.
Keyboard is not that great, but it was low profile and narrow, that is why i used that one. Wireless mouse allowed for easy storage.
I hope you enjoyed watching my video, and if you did, like and subscribe.
If you did not, please let me know why so i can improve and do better next time!
Also, feel free to tell me what you would like to see next.
Video was edited in OpenShot, and photos and movie was taken using digital camera.
Music:
Get Back Up - Silent Partner
How It Began - Silent Partner
Hear The Noise - John Deley and the 41 Players
Get Outside! - Jason Farnham
Poor Lv: 100
Ingenuos LV: It’s Over 9000!!!
Awesome!!!
That is brilliant, and the animation is great too. Nice work.
this makes me so happy :)
Nice idea diy laptop
Pretty neat idea! Not seen that many people attempt to make their own laptops.
Nice animation!
Nice build. The monitor can be slimed down significantly if you are willing to remove the case.
All of the stop motion animating in my opinion was just distracting. Like, just get to the build. I want to see the computer. If I wanted good stop motion, I'd have watched Wallace and Gromit.
Прикольно
I used the 12-volt output on the power supply for my monitor instead of the power brick
Cool! That's actually far better solution that i intended to go with but got some weird thick horizontal lines on screen. I powered mine through 4 pin psu connector for HDD's. Now i think that it could have been related to either psu itself, or some signal interference. It should totally work since psu's 12 volt rail has quite stable output. It reduces the amount of wires and power consumption too, eliminating unnecessary AC-DC conversions.
@@alephonya9390get a ssd
tbh, I like this more when you actually start from scratch rather than just buy a briefcase
I like your idea and build idea
Nice
Looks cool but the wire being exposed like that ruins the whole thing for me
can we get an asthetic update like paint or something
I thought about painting it in black and blue to match LEDs and knob and adding some decals, it would look pretty dope! I might get back to it in free time, but right now i am working on a different project, smaller and more portable, more like a bulky laptop kind of thing and it's consuming a lot of time, but hopefully it should be close to finish. I think i will get back to this concept, maybe make it a little bigger so it fits more standard parts like atx/sfx psu, bigger full HD monitor and full length gpu, add some better airflow, hide some cables, make it use only one external power cord etc. And make it look a little more like a actual pc this time rather than a 2 plywood boxes sandwiched together with a hinge! It has that vintage radio/vinyl player vibe to it tho.
@@alephonya9390 polish it and it will look more like it try disassembling the monitor it will help to pack it down more and your can route it's motherboard near the display port which will help to pack it smaller
@@MAKOS-ky5my I did disassemble it before but it has input sockets pointing vertically from the pcb making it hard to pack in the body and i did not want to solder too much at the time, so i just went with vesa mount. In the newer version i ended up using universal display controller that uses laptop displays which slimmed down the lid a lot.
What is this zoomer appealing editing?
I was looking for such a solution but one problem, I don't know whether you faced it or not, wood amplifies noise. So the cpu fan sound should be loud and if you add a GPU, then the the total noise would be significantly louder. But, yes, this idea is beautiful. I appreciate it very much and now you could refine it more. And think about the noise solution.
My post would be a less complete without mentioning your animation. It is lovely. I live in another continent. But I would request some beginners tutorials on animation, if you don't have already posted. I wanted to create some short animations but couldn't do that without proper interesting tutorial. I think, if you would make it, it would be very interesting. Regards and did I mention that your video is worth subscribing? ☺️
I haven't really noticed a lot of noise, but i might have developed higher tolerance from using a laptop, anything is quieter than that! But you're right, it could be a problem, especially if you like your setup very silent. The components are low power but if i were to use more powerful ones it would probably become a much bigger issue.
I am working on an refined version, it will be 3d printed and factor is smaller, and it solves most issues present in this one like poor case ventilation, not-so-good keyboard, display requiring additional power connection and many more. I'm planning to make it battery powered, it should be ready soon but printing takes longer that expected and I'm running into minor issues and solving them on the go. It will be more laptop-like, but i have plans for an improved case using mostly standard desktop components and standard monitor, too.
A tutorial on stop-motion animation sounds like an interesting idea! I'll try to make one when i am done with my current projects.
I'm glad you liked it, and thanks for pointing some issues and feedback.
Hey can u help me I'm new to this I was thinking about making a custom macbook case but idk where to start any ideas and plus I got cardboard its flimsy any ideas about that thanks
Hi, cardboard is nice for prototyping because its easy to cut, but for a case its not very good since its not durable enough and can absorb humidity easily. MDF is easy to work on and cheap, but brittle. Plywood is strong but quite annoying - requires hardware like saws and is dusty. 3D printing is good but you have to know how to make 3d models and either have 3d printer or let others do it for you (which can get quite expensive).
If you want to, for example, make a custom case that macbook would slide in, like a smartphone case, then it should not void warranty, and will require less work and will probably work better, because laptops have very packed components and a lot of engineering goes into it so that it works good, or at least good enough, for example cooling, interference (components are very close together so the effect is greatly multiplied).
I would recommend looking up some projects of cases that uses laptop hardware, and maybe some tutorials on how to work with desired material (i cant really recommend anyone because i learned stuff by trial and error, and still have a lot more to learn).
For small hardware like laptops i think making a 3d model after carefully measuring components (dimensions, where mounting holes go etc.) and then sending files to printing company would work the best, cause making a 3d model does not waste material and allows for quick design changes, and you see the result on-the-go.
You can check some free 3d software (i am using blender, but it can be quite intimidating at first, since it's not solely a modelling software), there are plenty available (blender, freeCAD, sketch up, etc.).
Or if you're more content with drawing you can draw parts and dimensions and sent it to a laser printing company (if you would like plywood) and glue parts together.
Making a case by hand from, for example plywood will take a lot of time to look at least decent enough (my case looks very blocky and crude and was not fast to make at all!).
I personally will be doing my next projects on 3d printer, its more convenient and looks better in my opinion.
I hope i helped at least a little.
TL;DR
@@alephonya9390 so what do u recommend to make for a chassis I don't really have that much I do have mdf and cardboard but
Do u or do u know anyone who does 3d printing service for a reasonable price thanks
@@BlackCat-qm3sj Since i can't recommend any printing service (i haven't used any, i just know they exist and how much it costs) i think it would be best to start with thin mdf if you want to see result fast (not too thin unless you add support, if you go too thick it will weight a lot and it will be harder to cut). For 3d printing you need to learn software or have to pay premium for design, but where's the fun in having your project designed for you?
Mdf will allow you to make an inexpensive prototype, a proof of concept, which can then be refined in latter version. Then you can decide if you prefer to stick with more manual way (wood, cutting, etc.) or go for 3d printing (it still takes a lot of work and planning, but in front of computer). In my opinion starting with wood and drawing would be best because it teaches you planning stuff which won't go to waste even if you decide to go other ways, and mistakes cost a lot less (if a print fails due to design mistakes, you basically have to print whole thing again). If you fail with wood, it usually means redoing one part.
With wood you can always use filler, sand it down and paint to hide the wooden texture and color if you don't like it.
An advice i can give (based on my still lacking knowledge and mistakes) is: measure components, draw parts on paper (take mdf thickness into account), add simple puzzle like interlocking for better glue adhesion. It's good to start with simple shapes, then add details where necessary, you can always sand edges and imperfections with sandpaper and glue some extra detail on. Good measurements are most important, and always measure in a constant manner (for example pencil leaves trail wider over time, use hard one and sharpen regularly). Parts that will be under stress (hinges for example) should be a part of a bigger piece or interlock with other parts (try not to glue edge to flat, it will break off easily, but if you must, add some support or screws).
I'm unable to help much, because i still don't know a lot, i can only share what i experienced with my current projects.
@@alephonya9390 but can cardboard but hardened tho I heard it can but if so how
@@alephonya9390 ah how about making a chassis like plastic can I make plastic I think I would need to buy silicone molding kit and then prob use some cardboard like make a mockup case and pour the molding kit in it then use some resin
But is there any alternatives to make or do something like a diy silicone molding kit and resin cuz the silicone mold making kit it's like 25 30 bucks and it's not that much in the box
😆