Thanks for taking the time to write it, its a fantastic reference. I mostly use the factory manuals but thought it worthwhile to include yours as well for benefit of others
@@popsbmw yes although you’ll either need to leave the ignition on (which will for sure flatten your battery) or you need to lift the small plastic cover behind the EPB switch and put your finger in towards the D on the gear selector and find a small white lever that you push up to allow you to put the car into neutral (assuming RHD car).
I think the procedure at the beginning was only to ensure the park brake was off (required for manual transmission cars), rather than actual service mode which gives you a bit more cable to play with
@@Shanes_Shed Manuals will engage the park brake when removing the key. That’s what you are preventing happening there. (By holding the epb switch down).
@@Shanes_Shed With a diagnostic tool you can set service mode, which I believe gives you more wriggle room on the cables when removing the shoes, and makes it much easier. There is a complex manual method, but I didn’t get it to work.
Bit hard to give a straight answer Ryan as I swapped to akebono pads with the rotor change. Previous to that I had the standard rotors with DBA pads. I remember I needed more brake pressure when cold, but that was probably more the pads than the rotors. I feel that they are an improvement once the rotors are hot - which living in the hills is not hard to do
Hi Shane just found your video because I am looking at buying a disco3 currently own a disco 2 with a worn-out engine $8k to rebuild i am 70 and I like the adjustable air suspension and comfort on the d3/4 the vehicle i am looking at has app 200k on the clock i know it's a hard question but am i buying a potential money pit or are they worth it THANKS SHANE
The air suspension is probably one of the best things about the D3/4 in my opinion. I’m actually planning a video that will answer your question. I can only account for my personal experience which is it’s a money pit
Gday Shane hi going mate ,, I just finished my handbrake module replaced the plastic gears on my 08 Range Rover sport tdv6 , now all done wonderfully except when can wheels trying handbrake there is no sound from module as I do test the motor fully functioning,,, do I need do anything such as reset handbrake module ? Many thanks mate Cheers Matt 🫡
I’m not 100% sure on what needs doing there mate as I’ve never had to play around with mine. I wouldn’t be surprised is there is something that needs resetting/calibrating. I’ll have a read if my manuals and see what I can find for you
So obvioulsy the workshop manuals don't have a section for replacing the handbrake actuator plastic gears. However they do have the procedure for replacing the whole lot - final step "Using T4, calibrate the parking brake actuator." If you have a Gap IID you'd be able to do it with that
@@Shanes_Shed Oh... that would explain why I couldn't rotate the disc. I figured I needed both wheels off the ground, but as long as it's in Neutral it should rotate with one wheel off / one wheel down?
@@Shanes_Shed Thank you! Kind of silly I didn't think of this when I had on stands / wheel off, I kept thinking the brakes were binding, rotor was warped, something was off. Yeah, keep it simple and put it neutral next time XD
Glad you could make use of my Brake Bible. 😎👍🏻
Thanks for taking the time to write it, its a fantastic reference. I mostly use the factory manuals but thought it worthwhile to include yours as well for benefit of others
I notice you don't have both wheels off the ground are you meant to I have seen others say both wheels off floor
@@popsbmw ideally with both off the ground but it can be done with one off the ground at a time if the car is in neutral so the wheel can turn. 👍🏻
@@MrBodsy cheers even on an auto
@@popsbmw yes although you’ll either need to leave the ignition on (which will for sure flatten your battery) or you need to lift the small plastic cover behind the EPB switch and put your finger in towards the D on the gear selector and find a small white lever that you push up to allow you to put the car into neutral (assuming RHD car).
Nice video Shane. I’m going to do this job next weekend, provided it’s not snowing here in UK 😎
Well have fun with the snow! Hot as in Perth over the last few days
I think the procedure at the beginning was only to ensure the park brake was off (required for manual transmission cars), rather than actual service mode which gives you a bit more cable to play with
I've just followed the LR service notes, dont think they gave any difference between manual and automatic.
@@Shanes_Shed Manuals will engage the park brake when removing the key. That’s what you are preventing happening there. (By holding the epb switch down).
@@Shanes_Shed With a diagnostic tool you can set service mode, which I believe gives you more wriggle room on the cables when removing the shoes, and makes it much easier.
There is a complex manual method, but I didn’t get it to work.
Andy K I'll have to dig into my IID tool when I get home from work and find the park brake service mode option in there I think
Great vid mate gow did you find the slotted rotors did it make a difference
Bit hard to give a straight answer Ryan as I swapped to akebono pads with the rotor change. Previous to that I had the standard rotors with DBA pads. I remember I needed more brake pressure when cold, but that was probably more the pads than the rotors. I feel that they are an improvement once the rotors are hot - which living in the hills is not hard to do
@@Shanes_Shed yeah when I was running dba rotors and pads I noticed the same thing , I now run dba rotors and then bendix pads which made a difference
@@OUTBACKDiscovery sorry, I just realised I ment to say I was running bendix pads. Its a DBA slotted rotor now however
@@Shanes_Shed ahh yep sweet yeah I thought slotted would make a difference
Hi Shane just found your video because I am looking at buying a disco3 currently own a disco 2 with a worn-out engine $8k to rebuild i am 70 and I like the adjustable air suspension and comfort on the d3/4 the vehicle i am looking at has app 200k on the clock i know it's a hard question but am i buying a potential money pit or are they worth it THANKS SHANE
The air suspension is probably one of the best things about the D3/4 in my opinion. I’m actually planning a video that will answer your question. I can only account for my personal experience which is it’s a money pit
Whats the axle nut size
32mm from memory
Gday Shane hi going mate ,,
I just finished my handbrake module replaced the plastic gears on my 08 Range Rover sport tdv6 , now all done wonderfully except when can wheels trying handbrake there is no sound from module as I do test the motor fully functioning,,, do I need do anything such as reset handbrake module ? Many thanks mate
Cheers
Matt 🫡
I’m not 100% sure on what needs doing there mate as I’ve never had to play around with mine. I wouldn’t be surprised is there is something that needs resetting/calibrating. I’ll have a read if my manuals and see what I can find for you
@@Shanes_Shed
Thank you sooooo much Shane you are our Legend 😎🫡
Thank u brothe 🫡
So obvioulsy the workshop manuals don't have a section for replacing the handbrake actuator plastic gears. However they do have the procedure for replacing the whole lot - final step "Using T4, calibrate the parking brake actuator." If you have a Gap IID you'd be able to do it with that
@@Shanes_Shed
Shane you are the best thank you for your time helping us you are our legend thank u again cheers Matt 🫡😎
No worries Matt.
Do i need to let the gear posiotion neutral? I'm stuck at rotating disc. Thanks for good guide vid.
It would definitely help to have the gearbox in neutral
@@Shanes_Shed Oh... that would explain why I couldn't rotate the disc. I figured I needed both wheels off the ground, but as long as it's in Neutral it should rotate with one wheel off / one wheel down?
@@Thoth0Amon should be able to rotate one wheel with the trans in neutral
@@Shanes_Shed Thank you! Kind of silly I didn't think of this when I had on stands / wheel off, I kept thinking the brakes were binding, rotor was warped, something was off. Yeah, keep it simple and put it neutral next time XD
you people never learn, grease things like that C/S Screw, wheel nut studs inc where they land on the alloy rim, otherwise good vid
thanks for the comment.