Couple of extra points to consider...ensure you drill the hole at a slight downward angle coming out so that any water can flow out of the pipe. Also use closed cell spray foam or waterproof sealant around the pipe. The standard expanding foam insulation actually wicks moisture.
Great tips! I wasn't aware the standard foam would be a problem. There are some brands of faucet manufacturers that already have the pitch designed into the unit where the length of the pipe is off-set a few degrees in relation to the face of the mounting flange. Prier is one brand with this feature. The installation doesn't require placing a nylon wedge under the flange to force the pitch. As long as the through-hole in the wall is at least 1 and an 1/8 inch diameter, the faucet should be able to self-drain. The drill diameter used in the video was 1 and 1/4 inch so the faucet should be good to go. To your original point, it is good practice and there would be nothing lost by drilling on a downward angle.
You could tell how much she appreciated it, glad they chose her for the project when you know they literally have thousands of request for help! ♡ I bet she sent him & crew home with cookies :-)
An informative video. Over the years I've installed and replaced a number of these faucets. Always found it best to first solder a length of pipe to the adapter before threading the adapter onto the faucet. Avoids the need to fully back out the washer/shaft assembly to protect the washer from the heat of the flame.
I agree. In theory, just slap the spigot back together but if experience is anything, they don't always seat exactly the way they did from the factory.
In order for the frost free valves to actually be frost free in the winter, it’s important to disconnect the hose from the valve and let it drain before the winter.
That, and actually installing it with a slope upward into the home... which Richard Trethewey did not. He started with an eyeball level, and by the end was angling downwards into the house. Not to forget to mention, he also didn't deburr the pipe for any of the joints for his tie-in to existing after cutting, as well he never disconnected and removed the old spigot.
How could even somebody push that "dislike button" ? Amazing to see the time and effort to put in to make such a video. Those who 'dislikies' ,try make a video and feel the pain to do the stuff, I've tried it, it takes 10 time more time to edit and upload it. I really appreciate This Old House;s helpfulness.
@@Phyrre56 Not necessarily cardio related. She could have knee/ joint issues, balance problems (inner ear issues and the like), or something else that makes getting up there difficult. All bodies work differently even if you can't see it from the outside.
Good idea to blow/suck out the dust from the hole BEFORE injecting the expanding foam 😁 Also, expanding foam adheres MUCH better if you slightly damped the service first. So spraying the inside of the hole with a mist of water from a little plant sprayer bottle would have worked well. It’s what I do. Great video though. Gotta love Richard 👍
Washer ain't bad either. See that blue tint? That's a shipping protector to keep the panel from being scratched before you set it up. You're supposed to peel that off. They make it blue so people can see it, lol. I know this because a got a house that came with a broken washer. It still has that sticker on it. It also has yellow print on the sticker that says "Remove Protective Cover" or something like that.
Now that was a good video Richard. Good information and excellent plumbing (of course)! Odd that they put the spigot so high in the first place (lazy builders).
Wonder if the house was raised onto a new foundation? Might have been over a crawlspace originally, then raised onto a mostly above-ground basement. My house was like this, and all sorts of things were way too high until I lowered them.
you guys should do a video with pvc pipe for those who have pvc[just starting DIY]... I had to put one in... took me a while to figure it out, but I got it in, and so far so good
They weren't kidding when they said old house. I think my parents had that same dryer when I was a kid. Come to think of it, my parents have the same red siding. Hey wait a sec.
My aunt inherited a Maytag washer and dryer my grandpa bought new in the mid-60’s, for my grandmother. In 1986 he replaced a belt, I repeated the job for her in 2008. Both still in use today.
I'm not a big fan of the frost-proof hose spigots. I've installed dozens for customers over the years, but they rarely last more than five years without a complete overhaul or full replacement. The brass hose bib is original to my 1926 home. I've replaced washers and bonnet packing twice during the 46 years that I have owned my home and it's good for many more decades. As long as water is turned off inside the house in the fall and the bib left open to drain, it's ready for our -30 deg. winters. Frost-proof spigots are also six times the cost of a standard brass hose bib.
I've seen it too, where these valves tend to wear out over a handful of years. To minimize the number of on/off rotation cycles, I've installed one of those brass ball valve hose fittings. This way, the hose bib valve can stay in the open position and the actual flow is controlled by the ball valve. Over the long haul, it's cheaper to replace the ball valve when it wears out in comparison to replacing the hose bib. Avoid the ball valves made from that inferior white metal. They react with a dissimilar metal and can weld itself to the hose bib.
I think a big problem with the frost-proof spigots is operator area. Because it takes awhile for them to drain, due to the long shut-off, people tend to want to kill them and sock the valve tight after it continues to drain. Be gentle, and they might last longer.
Coming from experience as a student, it's fun usually when a lot of manual labor isn't involved. Drilling through concrete is a pain in the butt, especially for a wall as thick as a foundation wall. However doing small tasks like this is kind of fun, not really hard, and not really satisfying in terms of quality of work compared to large scale jobs like finishing a basement from concrete to livable space. I really enjoyed my time working and learning general carpentry, but for a person like me (5'3" and 100 lbs) it's not easy when you gotta carry a semi-heavy tool bag and some extra tools every day. It's safe to say it's not my suited field, but it's nice to know for home fixes, just don't do large scale stuff or else carpenters will hate you =/ And people are usually nice when you're nice to them or do a good job. Others are nice cause they're paying you to do a good job and don't want no cheapskate infill unless they really can't afford it. The heavy work is usually more fun when you have a small group going to work with you that you get along with. Makes the job a lot less stressful with the added hands, faster job well done, and lighter atmosphere when the client wants to chat a bit. (It was really awkward when my supervisor went to buy stuff and the client walks out while we're tearing up a deck without not knowing much other than the basics and some tips and tricks) Sorry for the LONG freaking comment. More knowledge though =P
The biggest pain is getting people to pay their bills. I had a veterinarian, who happens to be deceased. He said that the people in the cemetery owed him $150,000.
This is exactly how Steve Lavamoniere or whatever his name is should act and behave with his customers. He's a hell of a plumber and I like watching his videos because we get to see 95% of the job he does but he really needs to work on his people skills. Everybody on This Old House seems so nice, my favorite is Norm Abraham.
going to install one of these, I have had WAY too many problems with the exterior spigot. They are a good design idea.. in Hawaii. Loved watching this show with my parents BTW. Just had a spigot fail closed, with my luck I will replace it, forget to close it in the winter and have to replace it again in the spring!
Hawaii? You guys get freezing temps? This type of Frost-Proof Spigot is meant for places where you get frost and the mechanism would freeze and get damaged.
The white plastic spacer (shown around 1:47) that he should have used on the outside is tapered (thicker at the top than bottom) to force the spigot to slope down to the outside to allow any standing water in the tube to drain out.
As usual super great video, but I have a question about Teflon tape... Richard wraps the threads many turns. How many turns is "just right" and how many turns is too much? I was told that you want just one or two layers of tape on the thread. Was this an old wive's tale?
I'm not an expert but I would say 2 layers is good. Tapered threads are supposed to seal by themselves and I think teflon tape or pipe dope is used so you can tighten the threads without too much friction.
Di-electric union is needed because a copper pipe is being connected to a steel spigot. They are dissimilar metals. Teflon tape, instead, is all that he uses.
Sharkbite will cause the faucet to spin. Although he used masonry screws, I never have the chance to. I'm usually replacing faucets and don't have enough material for the screw to hold, so I always solder the joint and silicone it into place (keeping the important plastic downward angle washer in place) Sharkbites would be SOOO much easier but the hole is usually too big to get both screws into enough material
Did not know about removing the stem/extension B4 soldering to protect seals from melting. Good to know should I ever install this type of valve. Thanks!
In Wisconsin, maybe we are dumb, we put our basements under ground, this one is away above ground and really doesn't have the R factor of a six inch wall. Just say not being able to reach the water faucet is not the only problem. We do rely on sump pumps, good to have a backup system in case of power failure.
Lol, Rich had the drill in hammer mode when he was driving the screws in. Also he used the wrong type of screws. I would have used a flat head screw. Although I suppose the countersink head screw works as well.
Should have 90ed out of the hose bib and stayed totally horizontal to the tie in and used a stop and drain valve so the residual water can be drained out!!
Great job . But definitely wouldn’t have placed heat on the adapter after the teflon was installed. Take an extra minute or two to dry fit , then sweat . Then stick the new hose bib in the wall , teflon , and screw . Don’t risk a leak when it could have been prevented
What about the flange to drain the water back out when turned off. I watched three this old house videos and none talked about the white flange on the outside
7:20 I don't get how a stainless braided hose is less prone to splitting or bursting than a non braided hose. They both are some kind of rubber or plastic hose just that one has a stainless braiding around it so sure it's more protected against abrasion and abuse but otherwise it seems like both would last the same amount of time as long as they weren't abused because they both have the same plastic hose, or do they? Tell me your thoughts.
There's no need to drill the hole at an angle. It's just need to be large enough so that the pipe going through the wall has enough room to tilt at an angle when the angled spacer that comes with the faucet is installed between the faucets and the wall. However, he did not install this spacer because he is basically just another high-priced hack with a TV show.
@@AlexSosaBolivia I agree and posted in another comment... "These frost free spigots are just fancy, poorly made junk. The solution is to install a regular old hose bib/spigot and properly winterize it before the freezing cold weather comes. There's no need for fancy "frost free" hose bibs. What tiny bit of water is left in the spigot after winterizing procedure is done properly will not be anywhere near enough to expand and damage the pipe or spigot when it freezes. Winterizing your outdoor spigot is easy. Step 1: disconnect hose from the spigot. Step 2: turn spigot on (FULL OPEN). Step 3: turn off the water to the spigot inside the house. Done. Do NOT close the outside spigot, leave it full open all winter. DO NOT REATTACH THE HOSE! LEAVE IT OFF! People have been doing this for decades and decades with no problems."
@@moistoreo6730 So by that logic, shut off valves should actually be placed at all water outlets eg. bathroom toilets, bathroom faucets and showers, washing machine water supply faucets etc.
For the part where he was mounting the faucet outside, the pilot holes he was drilling was so close to the hole for the pipe that there wouldn't be enough material for the screw to grab without breaking the concrete. Also why was his drill still on the hammer function while driving the screw? I'm not a plumber and this isn't really a criticism, I'm about to install one of these on my home so I'm just trying to find out what I'm missing here.
Ok missed an important part . Faucet should be not be level going thur wall. should be higher on inside then outside to allow any water remaining in faucet barrel to drain outside. Manufacturer recommends 5 degree downward pitch to outside .
Here in 2021. Why wasn't the original higher spigot not removed? You can see it at the end of the video. It would make a nice backup or secondary water source, however it's still leaky, so that leak should have been repaired, just as Richard has done before in other episodes.
They still make hose bibs with those deplorable mounting slots that are always too close to the pipe. The screws are rarely installed properly and eventually the bib comes loose. All they would need to do is make the flange a tiny bit wider and it would save everyone a headache.
wish he would have snagged abit of rebar the first hole :D hey Vinney, gimme another pound of flux, I dont have enough on the fitting yet., I love these shows honestly
We have a plumber in our town who got sick of going out on calls for estimates and then to only lose the bid. So he starting charging $100 for an estimate.
what size are the treads at the end of the hose bib. It is a model 17. I thought I had every fitting known to man. I would like it to be an elbow if possible. I would like to avoid shark bite which is what leaked and destroyed my wall.
Teflon tape starts melting at very very high temperatures. You would have to hold it above a fire for a while until it would start at least soften, let alone liquefy. It's like bakelite plastic. At it's raw stage, it melts at 100c but when it sets, it will only melt, hardly, at 800C and it wouldn't melt actually, it would start burning.
He applies Teflon tape and screws the copper fitting on the valve end, takes the valve all apart, then later uses a torch to solder the pipe on to the copper fitting - melting the Teflon tape that he put on the fitting on the valve end - why not solder the pipe first, then screw it on to the faucet end? Why did he not caulk (or use great stuff - like he did inside) around the outside of the faucet when he installed it? And how did he know, without taking measurements, that he wouldn`t have drilled through another pipe or anything else on or near the inside wall - wait, I know - he has superman vision!
Someone else did the preliminary work = thickness of the cement foundation. The spray insulation could have expanded through the foundation to the outside so calk on the outside wasn't needed.
Only thing on install is thread tape over the ends of pipe thread, this will cut off tape and possibly plug in system, maby not on hose valve , but say it goes to silonoid valve it wick use problems, 35 years experience running pipes water/ hydraulic/ air
He left out the critical step of creating a small downward angle towards the outside of the house. This assures complete drainage each time the water is shut off to prevent freezing. With the exception of Tom Silva, who is clearly a master carpenter, I think sometimes the other guys in this show are doing projects for the very first time.
The fact that the end of the spigot is open to atmosphere allows for the expansion of the water when it freezes. No need to drain it as there’s no sealed area for the water to build pressure.
I appreciate her immense enthusiasm
Yup, she's full of energy, and very appreciative. I would have liked to work for her.
The lady just improved my mood - god bless her
Couple of extra points to consider...ensure you drill the hole at a slight downward angle coming out so that any water can flow out of the pipe. Also use closed cell spray foam or waterproof sealant around the pipe. The standard expanding foam insulation actually wicks moisture.
Great tips! I wasn't aware the standard foam would be a problem. There are some brands of faucet manufacturers that already have the pitch designed into the unit where the length of the pipe is off-set a few degrees in relation to the face of the mounting flange. Prier is one brand with this feature. The installation doesn't require placing a nylon wedge under the flange to force the pitch. As long as the through-hole in the wall is at least 1 and an 1/8 inch diameter, the faucet should be able to self-drain. The drill diameter used in the video was 1 and 1/4 inch so the faucet should be good to go. To your original point, it is good practice and there would be nothing lost by drilling on a downward angle.
I agree, CyndiLH. I didn't pitch mine last winter...and well, you guessed it. Water all over the crawl space in the Spring.
These kind of videos is what RUclips should be promoting!
Very instructive & straightforward video!
I saw this on tv ,but that sweet lady makes it such a good video to see again.
You could tell how much she appreciated it, glad they chose her for the project when you know they literally have thousands of request for help! ♡ I bet she sent him & crew home with cookies :-)
I loved how excited she was to see Rich drill through the foundation haha
An informative video. Over the years I've installed and replaced a number of these faucets. Always found it best to first solder a length of pipe to the adapter before threading the adapter onto the faucet. Avoids the need to fully back out the washer/shaft assembly to protect the washer from the heat of the flame.
Thanks!
I agree. In theory, just slap the spigot back together but if experience is anything, they don't always seat exactly the way they did from the factory.
great idea thanks
Great tip!
wow richard missed that? lol
In order for the frost free valves to actually be frost free in the winter, it’s important to disconnect the hose from the valve and let it drain before the winter.
That, and actually installing it with a slope upward into the home... which Richard Trethewey did not. He started with an eyeball level, and by the end was angling downwards into the house. Not to forget to mention, he also didn't deburr the pipe for any of the joints for his tie-in to existing after cutting, as well he never disconnected and removed the old spigot.
@@JSLEnterprises so true I was thinking the same thing.
Richard makes it look so easy
I seen a lot of his videos and she was the most enthusiastic person ever
How could even somebody push that "dislike button" ? Amazing to see the time and effort to put in to make such a video. Those who 'dislikies' ,try make a video and feel the pain to do the stuff, I've tried it, it takes 10 time more time to edit and upload it. I really appreciate This Old House;s helpfulness.
That lady was so happy to not have to risk her life to turn on the hose anymore!
@@Phyrre56 Not necessarily cardio related. She could have knee/ joint issues, balance problems (inner ear issues and the like), or something else that makes getting up there difficult. All bodies work differently even if you can't see it from the outside.
Good idea to blow/suck out the dust from the hole BEFORE injecting the expanding foam 😁
Also, expanding foam adheres MUCH better if you slightly damped the service first. So spraying the inside of the hole with a mist of water from a little plant sprayer bottle would have worked well. It’s what I do.
Great video though. Gotta love Richard 👍
that dryer is a gem.
Hightower but probably works better than any one you cam buy today.
Its a maytag
Washer ain't bad either. See that blue tint? That's a shipping protector to keep the panel from being scratched before you set it up. You're supposed to peel that off. They make it blue so people can see it, lol. I know this because a got a house that came with a broken washer. It still has that sticker on it. It also has yellow print on the sticker that says "Remove Protective Cover" or something like that.
you learn so much from this guy. thanks Richard !
Wow that's a lot of Teflon
All in all a really good video. Not living in the north I wasn't really sure how the the hose bib like this functioned. Good info.
Now that was a good video Richard. Good information and excellent plumbing (of course)! Odd that they put the spigot so high in the first place (lazy builders).
Wonder if the house was raised onto a new foundation? Might have been over a crawlspace originally, then raised onto a mostly above-ground basement. My house was like this, and all sorts of things were way too high until I lowered them.
And value added - replaced the washer hoses just because they needed it and he saw it.
they didn't have a hammer drill and 18 inch bit handy was a lot easier to put it through the wood lol
I love her energy!
I do like the insulating cover on the old outlet pipe. It's like they want to make every attempt to make sure it freezes, lol.
I was wondering if someone else caught that, looking for some explanation I couldn't think of
you guys should do a video with pvc pipe for those who have pvc[just starting DIY]... I had to put one in... took me a while to figure it out, but I got it in, and so far so good
PVC pipe requires no effort, no skill, and just a cutter. You just cut, primer, and glue. Anyone can do PVC.
Straight to the point and clear to understand.
They weren't kidding when they said old house. I think my parents had that same dryer when I was a kid. Come to think of it, my parents have the same red siding. Hey wait a sec.
deltaray3 is that your grandma lol
My aunt inherited a Maytag washer and dryer my grandpa bought new in the mid-60’s, for my grandmother. In 1986 he replaced a belt, I repeated the job for her in 2008. Both still in use today.
@@brianpeters867 yjk
Lmmfao that's Great lol,
Gbfythbhhhbnbnmmo
Richard is soo badass. He & Tommy are great, they are all the best! Richard is so smooth!! :-) !!
I'm not a big fan of the frost-proof hose spigots. I've installed dozens for customers over the years, but they rarely last more than five years without a complete overhaul or full replacement.
The brass hose bib is original to my 1926 home. I've replaced washers and bonnet packing twice during the 46 years that I have owned my home and it's good for many more decades. As long as water is turned off inside the house in the fall and the bib left open to drain, it's ready for our -30 deg. winters. Frost-proof spigots are also six times the cost of a standard brass hose bib.
I've seen it too, where these valves tend to wear out over a handful of years. To minimize the number of on/off rotation cycles, I've installed one of those brass ball valve hose fittings. This way, the hose bib valve can stay in the open position and the actual flow is controlled by the ball valve. Over the long haul, it's cheaper to replace the ball valve when it wears out in comparison to replacing the hose bib.
Avoid the ball valves made from that inferior white metal. They react with a dissimilar metal and can weld itself to the hose bib.
I think a big problem with the frost-proof spigots is operator area. Because it takes awhile for them to drain, due to the long shut-off, people tend to want to kill them and sock the valve tight after it continues to drain. Be gentle, and they might last longer.
I fell like this would be fun to do as a job. Interact with nice (usually) people and then do some fun work.
Coming from experience as a student, it's fun usually when a lot of manual labor isn't involved. Drilling through concrete is a pain in the butt, especially for a wall as thick as a foundation wall. However doing small tasks like this is kind of fun, not really hard, and not really satisfying in terms of quality of work compared to large scale jobs like finishing a basement from concrete to livable space.
I really enjoyed my time working and learning general carpentry, but for a person like me (5'3" and 100 lbs) it's not easy when you gotta carry a semi-heavy tool bag and some extra tools every day. It's safe to say it's not my suited field, but it's nice to know for home fixes, just don't do large scale stuff or else carpenters will hate you =/
And people are usually nice when you're nice to them or do a good job. Others are nice cause they're paying you to do a good job and don't want no cheapskate infill unless they really can't afford it.
The heavy work is usually more fun when you have a small group going to work with you that you get along with. Makes the job a lot less stressful with the added hands, faster job well done, and lighter atmosphere when the client wants to chat a bit. (It was really awkward when my supervisor went to buy stuff and the client walks out while we're tearing up a deck without not knowing much other than the basics and some tips and tricks)
Sorry for the LONG freaking comment. More knowledge though =P
The biggest pain is getting people to pay their bills. I had a veterinarian, who happens to be deceased. He said that the people in the cemetery owed him $150,000.
This is exactly how Steve Lavamoniere or whatever his name is should act and behave with his customers. He's a hell of a plumber and I like watching his videos because we get to see 95% of the job he does but he really needs to work on his people skills. Everybody on This Old House seems so nice, my favorite is Norm Abraham.
This man is a saint!
This lady is adorable. I like this video
Shouldn't you add the plumber's tape after you solder the joint 2" inches away rather than take a chance and melt it?
Rich to the rescue! Nice job!
I’ve got to replace one myself.
2:56 the camera man was just like "Make it look like you are doing something"
going to install one of these, I have had WAY too many problems with the exterior spigot. They are a good design idea.. in Hawaii. Loved watching this show with my parents BTW. Just had a spigot fail closed, with my luck I will replace it, forget to close it in the winter and have to replace it again in the spring!
Hawaii? You guys get freezing temps? This type of Frost-Proof Spigot is meant for places where you get frost and the mechanism would freeze and get damaged.
Fun lady. Hard to believe they'd put the spigot that high.
He left the old valves there for when she grows.
Haha
People stop growing at around 18 years
So she will now only slowly shrink in size
She looks like to be around 55-70 years old
Lol
Adam SK/EN wait people shrink?!
@@kevinjr.8768 yrs, as you age your spinal column collapses and you shorten in height.
at 2:16 "the hardest part of this job is drilling through this wall" (wait for it...) oh! i love her reaction..
-Why dont you turn on the hose.
-Wow! The water flows....thats cool!!! lol
this is better than the last video that has that fancy overpriced adapter you had to use every time
gtasandman i agree.
Would it be wise to slope the Frost-Proof Hose Spigot a tiny bit so the water on the outside would drain out and not freeze ?
Bill Rossey yes if there’s room or if your wall is not to wide, but there won’t be much water left in the pipe to freeze.
The white plastic spacer (shown around 1:47) that he should have used on the outside is tapered (thicker at the top than bottom) to force the spigot to slope down to the outside to allow any standing water in the tube to drain out.
Free!!!!!
Pleasant Lady.
Thank you . God Bless !!!
As usual super great video, but I have a question about Teflon tape... Richard wraps the threads many turns. How many turns is "just right" and how many turns is too much? I was told that you want just one or two layers of tape on the thread. Was this an old wive's tale?
I'm not an expert but I would say 2 layers is good. Tapered threads are supposed to seal by themselves and I think teflon tape or pipe dope is used so you can tighten the threads without too much friction.
Di-electric union is needed because a copper pipe is being connected to a steel spigot. They are dissimilar metals. Teflon tape, instead, is all that he uses.
The spigot may be chrome plated brass.
That’s where he will nail her for the big money repair job.
I wish they would do a replacment spigot when the lines are in the wall. With no access and not in a basement of crawlspace.
Pretty similar process only a part of a floor or a part of a wall will have to be cut out. Or part of the floor and the wall.
I like this video. Good stuff.
Any reason why you could not use a shark bite adaptor...it would be solder free and you would not have to worry about damaging the seals?
Doesn't the heat damage teflon tape during the soldering?
No, more than a Teflon frying pan. Heat it hot enough to accept the solder, just not hot enough to make the pipe molten and you're good. 👍🏻
Could you show more videos on sharkbite type or pex fittings for plumbing purposes?
Sharkbite will cause the faucet to spin. Although he used masonry screws, I never have the chance to. I'm usually replacing faucets and don't have enough material for the screw to hold, so I always solder the joint and silicone it into place (keeping the important plastic downward angle washer in place)
Sharkbites would be SOOO much easier but the hole is usually too big to get both screws into enough material
Did not know about removing the stem/extension B4 soldering to protect seals from melting. Good to know should I ever install this type of valve. Thanks!
Is it just me or does that new copper slant up? Do it right all even horizontally Richard
Can you repair these long taps like the reseating of the old style? Or do you have to pull the long neck out and replace?
In Wisconsin, maybe we are dumb, we put our basements under ground, this one is away above ground and really doesn't have the R factor of a six inch wall. Just say not being able to reach the water faucet is not the only problem.
We do rely on sump pumps, good to have a backup system in case of power failure.
Another great video! 👍
Lol, Rich had the drill in hammer mode when he was driving the screws in. Also he used the wrong type of screws. I would have used a flat head screw. Although I suppose the countersink head screw works as well.
Should have 90ed out of the hose bib and stayed totally horizontal to the tie in and used a stop and drain valve so the residual water can be drained out!!
Lmao he cut away before she asked for the price 🤣
Great job . But definitely wouldn’t have placed heat on the adapter after the teflon was installed. Take an extra minute or two to dry fit , then sweat . Then stick the new hose bib in the wall , teflon , and screw . Don’t risk a leak when it could have been prevented
What about the flange to drain the water back out when turned off. I watched three this old house videos and none talked about the white flange on the outside
7:20 I don't get how a stainless braided hose is less prone to splitting or bursting than a non braided hose.
They both are some kind of rubber or plastic hose just that one has a stainless braiding around it so sure it's more protected against abrasion and abuse but otherwise it seems like both would last the same amount of time as long as they weren't abused because they both have the same plastic hose, or do they? Tell me your thoughts.
I wondering how long,the lady had been used the stool to turn on the water hose...
He didn’t seem too concerned about mounting that spigot at a slight downward angle to facilitate drainage.
Alejandro Sosa he doesn’t seem too concern about your comment either
@@KR-ne1bl His lack of concern in no way invalidates my observation.
There's no need to drill the hole at an angle. It's just need to be large enough so that the pipe going through the wall has enough room to tilt at an angle when the angled spacer that comes with the faucet is installed between the faucets and the wall. However, he did not install this spacer because he is basically just another high-priced hack with a TV show.
Vlad The Impaler Țepeș III and a downward angle won’t help a bit if you’re st00pid enough to keep the hose attached over the winter.
@@AlexSosaBolivia I agree and posted in another comment...
"These frost free spigots are just fancy, poorly made junk. The solution is to install a regular old hose bib/spigot and properly winterize it before the freezing cold weather comes. There's no need for fancy "frost free" hose bibs. What tiny bit of water is left in the spigot after winterizing procedure is done properly will not be anywhere near enough to expand and damage the pipe or spigot when it freezes. Winterizing your outdoor spigot is easy.
Step 1: disconnect hose from the spigot.
Step 2: turn spigot on (FULL OPEN).
Step 3: turn off the water to the spigot inside the house.
Done.
Do NOT close the outside spigot, leave it full open all winter.
DO NOT REATTACH THE HOSE! LEAVE IT OFF!
People have been doing this for decades and decades with no problems."
Nice video. Should have removed old faucet not to have future problems with it.
Good job !!!!!!
What if you are getting your supply from the main. Exterior.
Why install a shut-off valve if you have a frost free garden faucet ?
To be able to service the valve without shutting down the entire building.
@@moistoreo6730 So by that logic, shut off valves should actually be placed at all water outlets eg. bathroom toilets, bathroom faucets and showers, washing machine water supply faucets etc.
@@rcarioca Yes and all those items you listed generally do have shut-offs.
For the part where he was mounting the faucet outside, the pilot holes he was drilling was so close to the hole for the pipe that there wouldn't be enough material for the screw to grab without breaking the concrete. Also why was his drill still on the hammer function while driving the screw? I'm not a plumber and this isn't really a criticism, I'm about to install one of these on my home so I'm just trying to find out what I'm missing here.
Surprised that more people didn’t catch that.
Ok missed an important part . Faucet should be not be level going thur wall. should be higher on inside then outside to allow any water remaining in faucet barrel to drain outside. Manufacturer recommends 5 degree downward pitch to outside .
Here in 2021. Why wasn't the original higher spigot not removed? You can see it at the end of the video. It would make a nice backup or secondary water source, however it's still leaky, so that leak should have been repaired, just as Richard has done before in other episodes.
Don't forget to disconnect the hose in the winter time it would keep the water from draining and split the pipe in the winter.
I think the hole should have been a little smaller as the concrete screws were very close to the hole.
Why didn't you put chalking insulator around the Spigot before screwing it to the outer concrete wall on the outside.
Yea I was thinking the same, they usually come with a Teflon plastic spacer/washer to go between the house and the silcock to create a better seal
Hi Richard my faucet looks like same as in this vid but don't have any access from inside the house any idea how you replace it
They still make hose bibs with those deplorable mounting slots that are always too close to the pipe. The screws are rarely installed properly and eventually the bib comes loose. All they would need to do is make the flange a tiny bit wider and it would save everyone a headache.
They just left the old hose bib that's already leaking...
no caulk? concrete screws orplastic anchorand stainless screws?
Looked like a different hose also. Did not take any time to clear the air out of the hose, got water right away.
That was cool.
why didnt he make the tie in level w/ the new spigot or visa versa?(inside)
you don't put any silicone caulk on outside to keep water out?
Great vid, should have removed the old hose bib and piping though.
That’s cool. For the inside connection, is it okay to use threaded pipe/tube , no soldering?
What if your drilling in to the concrete and hit rebar?
you fill the hole with hydraulic cement and start over
5:35 - Man, I wish Rich would have said that sooner before I flooded my whole basement...
Why not sodder 1st and then thread that after ?
You need a rappel house and a wall brace, to step up 4 inchs?
Does the water that is trapped in like the last 4 inches not freeze?
wish he would have snagged abit of rebar the first hole :D hey Vinney, gimme another pound of flux, I dont have enough on the fitting yet., I love these shows honestly
He didn't ream out (deburr) the copper tubing when cut. Will cause turbulence, and cavitation!!
I was looking through the comments to see if anyone else noticed
He also didn't install an reciprocating dingle arm to help reduce sinusoidal repleneration
@@jimrussell8080 you are just so funny
How much you charged for this work Richard ?
What about the old faucet? It's just there
She’s fun to watch
RIGHT WAY TO DO IT, BUT ON LONG ISLAND IN NY. THAT WOULD BE AROUND 800 DOLLAR JOB !
We have a plumber in our town who got sick of going out on calls for estimates and then to only lose the bid. So he starting charging $100 for an estimate.
the shark bite technology may have been interesting for this application..
How?
I wish he would have shown how to put that spigot back together after soldering.
what size are the treads at the end of the hose bib. It is a model 17. I thought I had every fitting known to man. I would like it to be an elbow if possible. I would like to avoid shark bite which is what leaked and destroyed my wall.
Doesn't that torch totally destroy the teflon tape?
Teflon tape starts melting at very very high temperatures. You would have to hold it above a fire for a while until it would start at least soften, let alone liquefy. It's like bakelite plastic. At it's raw stage, it melts at 100c but when it sets, it will only melt, hardly, at 800C and it wouldn't melt actually, it would start burning.
He applies Teflon tape and screws the copper fitting on the valve end, takes the valve all apart, then later uses a torch to solder the pipe on to the copper fitting - melting the Teflon tape that he put on the fitting on the valve end - why not solder the pipe first, then screw it on to the faucet end? Why did he not caulk (or use great stuff - like he did inside) around the outside of the faucet when he installed it? And how did he know, without taking measurements, that he wouldn`t have drilled through another pipe or anything else on or near the inside wall - wait, I know - he has superman vision!
Someone else did the preliminary work = thickness of the cement foundation. The spray insulation could have expanded through the foundation to the outside so calk on the outside wasn't needed.
Could have saved a 90 bend if he would have planned a little better and moved the whole thing up 3 inches
That lady’s been outside playing with that hose since 2016.
Only thing on install is thread tape over the ends of pipe thread, this will cut off tape and possibly plug in system, maby not on hose valve , but say it goes to silonoid valve it wick use problems, 35 years experience running pipes water/ hydraulic/ air
que buen trabajo.gracias
He left out the critical step of creating a small downward angle towards the outside of the house. This assures complete drainage each time the water is shut off to prevent freezing. With the exception of Tom Silva, who is clearly a master carpenter, I think sometimes the other guys in this show are doing projects for the very first time.
wouldnt you just need some of the water to drain, enough so that any water left in if it freezes has plenty of room?
he said at the 2:00 min mark with the frost proof sillcock no need to turn off the water in the winter
I thought it was an anti freeze tap
Rich is a master plumber. He has been on This Old House since the very first season.
The fact that the end of the spigot is open to atmosphere allows for the expansion of the water when it freezes. No need to drain it as there’s no sealed area for the water to build pressure.