Thanks for the tutorial! Unfortunatelly my SIM800c module is slightly different. It has the following sequence of pins: Top side: 5v, V_TTL, GND, TXD, RXD, DTR, SPKP, SPKN Bottom side: MICN, MICP, Ri, VRTC, GND, PWR, GND, VBAT The vendor told me that the module already comes with an internal antena, but it also has a connector for another external one. So I decided do not purchase the extra antena, and now I wondering if this can affect the behaviour of SIM800c. The module is being powered from an external 12V power supply connected to a step down module lm2596 adjusted to give the 4V required by SIM800c. I also use the capacitors and the zener diode as recommended in the module datasheet. The power supply is connected to the 5V pin, and when I turn on the circuit a red LED light up indicating tht the the power is on, but no blinking LED appears on the module. Before trying things that can damage my module, I would be very happy if you could help me to answer the following questions: Can I power the module with 5v through the 5v pin, instead of 4v? I want to trying this because I’m getting around 2,74 in the VBAT pin, when I power the module with 4v. I also ask to myself why there is a 5v pin in the module since the maximum voltage recomended for SIM800c is 4.4v. Can I power the module through the VBAT pin, using the same power supply or a 9v Ni-Mg battery + step down, instead of the Li battery recommended in the datasheet? Should I use an external antena as well? Thanks in advance. My module is the same showed in the link www.bizkit.ru/en/2019/02/05/13553/
Is it possible to power the Arduino from the same power source such as the lipo you are using ? In case some switches are added to the project and an lcd screen as well, it could make a nice portable phone.
Arduino will need 5v to work. This lithium battery will only provide 3.7volts. So you may need to use a dc boost converter to boost 3.7v to 5v in order to power arduino. This will work fine and i have used that method without any issues. Please try my other videos also to get new ideas
when i connect 3 grounds together the sketch is not uploading , and when i remove the ground from srduino the code runs but no response from the sim800c?
Hey bro, I am going to have a SIM800C shield which is my own. I want to ask something; which pins are correspond to RX and TX in SIM800C? Are they UART1? Sorry for my ignorance.
Ciao. Molto interessante e utile. Ti chiedo gentilmente di dirmi se è indifferente usare anzichè ARDUINO UNO il mod. ARDUINO NANO penso sia possibile; cambiano i cablaggi? Grazie e saluti
In receive SMS mode. I able to get the message send from mobile phone. But it include some other text for example if I send "Hello", in Serial Monitor I'll receive ⸮⸮⸮⸮⸮⸮⸮⸮⸮⸮⸮⸮⸮⸮⸮⸮⸮⸮ .. (and other information) Hello. Is that normal? How to get retrieve only "Hello" I don't need other information.
Thank you bro it's very helpful to me for doing my mini project ❤
Thank you friend ❤️
I've seen commonly using a diode to drop 5V to the required level. Btw - a nice video.
thank you brother ❤️
I am using a pic microcontroller to do the same thing. I receive the message but my phone says content not supported.
Thanks for the tutorial! Unfortunatelly my SIM800c module is slightly different. It has the following sequence of pins:
Top side: 5v, V_TTL, GND, TXD, RXD, DTR, SPKP, SPKN
Bottom side: MICN, MICP, Ri, VRTC, GND, PWR, GND, VBAT
The vendor told me that the module already comes with an internal antena, but it also has a connector for another external one. So I decided do not purchase the extra antena, and now I wondering if this can affect the behaviour of SIM800c.
The module is being powered from an external 12V power supply connected to a step down module lm2596 adjusted to give the 4V required by SIM800c. I also use the capacitors and the zener diode as recommended in the module datasheet. The power supply is connected to the 5V pin, and when I turn on the circuit a red LED light up indicating tht the the power is on, but no blinking LED appears on the module.
Before trying things that can damage my module, I would be very happy if you could help me to answer the following questions:
Can I power the module with 5v through the 5v pin, instead of 4v? I want to trying this because I’m getting around 2,74 in the VBAT pin, when I power the module with 4v. I also ask to myself why there is a 5v pin in the module since the maximum voltage recomended for SIM800c is 4.4v.
Can I power the module through the VBAT pin, using the same power supply or a 9v Ni-Mg battery + step down, instead of the Li battery recommended in the datasheet?
Should I use an external antena as well?
Thanks in advance.
My module is the same showed in the link www.bizkit.ru/en/2019/02/05/13553/
you cant power from 5v pin.
And also it requires atleaset 2A current from the supply
Bina capacitor use kiye kar sakte hai?
may i know why have you connected the reset pin with ground pin?
Coz its sim800 C module
how much current does the connected cell provides?
is it able to compensate for the 2A requirement at transmission burst?
Yes. This battery is capable of supplying 2A when needed
Hello, nice video. Is it possible to read senders number and replay to it with with some info. E.g. sensor value.. Thanks
Can i use 3.3 V of Arduino to Gsm
Very Good Lesson. Thanks a lot
Thank you for this video btw. You did really well.
Glad you enjoyed it!
Is it possible to power the Arduino from the same power source such as the lipo you are using ? In case some switches are added to the project and an lcd screen as well, it could make a nice portable phone.
Arduino will need 5v to work. This lithium battery will only provide 3.7volts. So you may need to use a dc boost converter to boost 3.7v to 5v in order to power arduino. This will work fine and i have used that method without any issues. Please try my other videos also to get new ideas
Is it compulsory to use only 2g sim with 800l or i can use my airtel 4g sim with this
You can use any sim
What is a boot pin used for ?
i have explained it
when i connect 3 grounds together the sketch is not uploading , and when i remove the ground from srduino the code runs but no response from the sim800c?
Need to see circuit and check the components. May be GSM module is burnt
power supply is not correct that's why it off the arduino after removal it starts to blink the arduino
can i use the same code for SIM800c
Yes
Ayye mekama temperature eka menala eka ganakata wada wedi wena kota alert message ekak ganne kohomada
oya neda call kale? Wade hari neda
Hi can i send same Msg to Multiple Mobile numbers (eg- two mobiles) if yes can you tell me how to edit code?
Yes
@@tronicslk can you tell me how? Would be a huge help 🤗
@@pubuduperera3959 0717447767 whatsapp
sim800l eke power consumption kohomada
Stand by 18 mA
Call
GSM850 199 mA
EGSM900 216 mA
DCS1800 146 mA
PCS1900 131 mA
GPRS 453 mA
Transmission burst 2 A
Ublox Neo6m eke power consumption kohomada
Hey bro,
I am going to have a SIM800C shield which is my own. I want to ask something; which pins are correspond to RX and TX in SIM800C? Are they UART1?
Sorry for my ignorance.
Can you show me the module. Same chip is used in video
Amazing video
if the module's led is not on does it means the module has problem?
Yes. If u provide power properly, there is a issue with module
Do this work the version 2 of sim800?
yes. It will work
What parts of the code are needed to be changed if ak
Hi...Is Arduino output pins(Tx,Rx) voltage level (5V) compatible with SIM800 pins voltage level (which may be 3.3V) ?
Yes. It is compatible. No need of logic level converters
Is it necessary that we should use 2g sim card. I have no 2g sim card and i can't find it anywhere
Dada please tell me i am in trouble pls help me 🙏🙏🙏🙏🙏
Vodafone Airtel will work not jio
the status led does not blink at all on my SIM800C , What is the problem?
may be damaged module or wrong power supply
Nice content Gr8
Sir, this module is not messaging Android phones. It is a small multimedia phone, messaging it.
Please reply me
should observe the circuit
what is the size of the capacitor?
u can see it on video. 1000 uf or 2200uf is good
Hey bro mu gsm is not working at commands are not showing please any solutions?
Sir where we can find software serial Library? pls help sir
it comes with arduino ide by default. No need to install again
Great video
Ciao. Molto interessante e utile. Ti chiedo gentilmente di dirmi se è indifferente usare anzichè ARDUINO UNO il mod. ARDUINO NANO penso sia possibile; cambiano i cablaggi? Grazie e saluti
È lo stesso amico mio
Why you use capacitor
To Stabilize the voltage
In receive SMS mode. I able to get the message send from mobile phone.
But it include some other text
for example if I send "Hello", in Serial Monitor I'll receive ⸮⸮⸮⸮⸮⸮⸮⸮⸮⸮⸮⸮⸮⸮⸮⸮⸮⸮ .. (and other information) Hello.
Is that normal?
How to get retrieve only "Hello" I don't need other information.
I have done a seperate tutorial on this. Please watch it ✌️
@@tronicslk Thank you
Hi, thanks for this video quite useful, I was wondering, do I have to connect the rx if I am planning only to send sms ?
Yes you should
@@tronicslk How come? There must be a reason.
can i use 4G sim for sim800L
Yes you can.
Code file is not open sir
Very important video💪
Glad you liked it
can you use 4g on the gsm800l
No you can't
You can use airtel sim card as it supports 2G
What are the total costs of all modules used in this video?
Code file not open. Kindly explain how to open. I want to learn from you.
Thanks ❤
it works finr
Sir we r tried so many times but it's not working sir... Plz give some solution
watch the video carefully
Aurdino me Jo library Jo use ke hai apne uski zip file dedo
SIM is 2G,3G or 4G ?
yes you can use all 2G,3G,4G,
but server internet output 2G
Rohith is correct
Good video. This is good to learn, or made projects for your house. I See you video Facebook Group, I subscribe you Channel :).
Thank you very much brother
I think that u may put the name of the component in the video
Sim800 + 2200uf capacitor. Thats all
Sir, I am also your subscriber. Answer me as well.
I asked you sir that GSM module is not messaging on Android phone. Please answer this.
there are lots of reasons which cause this. cant tell exactly without observing
@@tronicslk Sir call is doing GSM modem but SMS is sent. Sim shows in memory but does not show in phone.
Place a call ! 😂👍
Super
wooooooow. great....
Thank u
Sor I am not receiving message sent...
Is GSM module working properly (power supply and led blink rate)
I Will use 3.3v then
not enough voltage and current. Dont use it
Sir can you re send this code
it is in description
super
Thank you
nice..
💥💥✌️
I have a module
sim800l v2
and its not working
Did u give power correctly?
And how to power it corectly...
This is fake.
Reason?