From so many videos seen, this is the only turner who at least uses hand protection when he uses the lathe, and it is clear that he is detailed in the work he does, which gives quality and good service, Greetings from Venezuela
Good done for toys. For heavy work machine it is not useable. Bought a used machine and found such a work in it. Repaired part lost half of material because of not hard enough.
I've fixed lots of gears and that's it. It has to be hard to survive. It is a good idea to run the gears in by turning by hand with grinding paste to get the fit right. Obviously clean it properly before installing it.
Because that is the proper way to do it. These gears are hardened. So the welding ruined the hardness to the surrounding teeth, and his welding method is poor. You need a continuous bead to set the weld. Him pecking at it never got the metal hot enough to penetrate.
Mevcut dişli sert çelikten aşinmasi zor fakat yapilan kaynak yumuşak metal oldugu için uzun ömürlü olmaz diye düşünüyorum, belki tek diş kirik olduundan uzun süre araci hareket ettirebilir ama riskli
Need to do this on my transmission. I just put it back together and pretended i didnt see that. I bet the tooth you welded on is stronger than the rest of the teeth. How much money did you just save?
I'll go further & say it's dangerous to wear any loose clothing while using any machine that can catch it. I once seen a guy use his foot on a lathe handle to get it unstuck. His shoelace got caught & his foot slowly got pulled clockwise under & up the backside of the adjustment handle dial. It tightened his shoelace so he couldn't pull his foot out. Fortunately there was a guy walking past when this happened & he shut it down before it did serious damage. His foot was broken in 4 places as well as 3 toes. If the guy didn't stop the machine it would have rolled his foot then his ankle & on up his shin. Who knows how much of his leg could have gotten rolled up? Lucky Bastard.
@@peterzinia3767 exacto, a una estudiante de Escuela secundaria Técnica en el país de México a unas calles de dónde vivo un torno le destrozó el brazo izquierdo.
1. Все шестерни имеют поверхностную закалку токами высокой частоты. Отремонтированный зуб будет без неё. 2. Пятно контакта на этом зубе будет располагаться в неправильном месте и в итогу зуб будет усиленно изнашиваться.
I don't know how long it'll last but I guess gotta do what you have to do. The welding isn't as good as the lathe work but nice job. Doesn't happen in the US.
I don’t usually comment but I couldn’t stand seeing all this misinformation. More than one tooth make contact. So long as it’s there as a “placeholder” I think it’ll work for long time. It’s definitely a harder tooth than most would think. If you’re thinking about it, try it!
długo nie pojeździ. zmieniona struktura materiału tzw. "heat zone", brak jakiegokolwiek wyżarzania normalizującego lub odpuszczania materiału po wytworzeniu naprężeń, nie nawęglono (nie zastosowano również innej metody wzmocnienia materiału np. azotowanie). typowa garażowa robótka byle coś działało. ten film jest raczej z gatunku jak nie należy naprawiać części maszyn
this works maybe as a one time fix but the way you sanded down all the teeth just to make them even will wear it with repeated repair. also the welds were pulsed instead of strung which makes me question the integrity
And someone wants to continue to use it? After all, this tooth has a different strength from the rest of the teeth, a different grade of steel, a different hardness ... Probably only Kamikaze will use this gear ...
Here we go , another bodge , poor welding , heat treatment lost on surrounding teeth , I wonder how long it lasted , its not often economical to repair gears
Bonsoir mais ils n'attendent que vous pour leur trouver une meilleure solution ne vous gênez surtout pas pour aller leur montrer de quoi vous êtes capable dans leur condition de vie !
From so many videos seen, this is the only turner who at least uses hand protection when he uses the lathe, and it is clear that he is detailed in the work he does, which gives quality and good service, Greetings from Venezuela
he do not know the safety rules and regulation in lathe.
That's a good idea using the calipers to scribe a nice straight line
Pakistani brain and talent is next level ❤❤❤ love from India more iq level doing great and technical work ❤❤❤
ماشاءاللہ جی۔ بہت اچھا کام ہے۔
Sometimes you have to do what you have to do looks like it worked out pretty good
0:38 The electrode type is ch 80 R. it is a hard-coating electrode.
What is this electrode made of?
@@greasyHands66 the result is if you need a very hard surface this is the electrode. some titanium.
Wow can never ask for better work
Thank u sir 😊
Good done for toys. For heavy work machine it is not useable.
Bought a used machine and found such a work in it. Repaired part lost half of material because of not hard enough.
I've fixed lots of gears and that's it. It has to be hard to survive. It is a good idea to run the gears in by turning by hand with grinding paste to get the fit right. Obviously clean it properly before installing it.
What about if you re-harden the steel?
Техника безопасности на высоте! браво!
кроме момента с надетыми перчатками и вращающегося патрона...
@@ukrplant3955 Это был сарказм)
What aboit heat treatment
عمل رائع جيد بتكلفة قليلة وفرت الكثير
وأضن أنه لحم بسيخ كروم وهو لحام قوي وقابل للأحتكاك عمل رخيص وناجح وكفول 👌👍
👏👏👏👍 jaka elektroda była. użyta do naprawy?
Ye kon sa welding process se weld kiga gaya please bataye technically
😊una obra d arte la presicion
Countries abroad don't throw away things they repair them unlike USA just toss 2 junkyard.
Because that is the proper way to do it. These gears are hardened. So the welding ruined the hardness to the surrounding teeth, and his welding method is poor. You need a continuous bead to set the weld. Him pecking at it never got the metal hot enough to penetrate.
Very good Job congratulations
Здравствуйте,робота зделана хорошо мне нравится.Один вопрос , почему вы себя не бережёте? Желаю вам всего хорошего.
Mevcut dişli sert çelikten aşinmasi zor fakat yapilan kaynak yumuşak metal oldugu için uzun ömürlü olmaz diye düşünüyorum, belki tek diş kirik olduundan uzun süre araci hareket ettirebilir ama riskli
Need to do this on my transmission. I just put it back together and pretended i didnt see that. I bet the tooth you welded on is stronger than the rest of the teeth. How much money did you just save?
Nice work. Sounds like you're using helium shield gas ;)
Will IT handle Theo preasure because i,m note shore????
من الخطئ ارتدائك القفزات عند العمل بالمخرطه
I'll go further & say it's dangerous to wear any loose clothing while using any machine that can catch it. I once seen a guy use his foot on a lathe handle to get it unstuck. His shoelace got caught & his foot slowly got pulled clockwise under & up the backside of the adjustment handle dial. It tightened his shoelace so he couldn't pull his foot out. Fortunately there was a guy walking past when this happened & he shut it down before it did serious damage. His foot was broken in 4 places as well as 3 toes. If the guy didn't stop the machine it would have rolled his foot then his ankle & on up his shin. Who knows how much of his leg could have gotten rolled up? Lucky Bastard.
@@peterzinia3767 exacto, a una estudiante de Escuela secundaria Técnica en el país de México a unas calles de dónde vivo un torno le destrozó el brazo izquierdo.
1. Все шестерни имеют поверхностную закалку токами высокой частоты. Отремонтированный зуб будет без неё.
2. Пятно контакта на этом зубе будет располагаться в неправильном месте и в итогу зуб будет усиленно изнашиваться.
Пока он износится трактор сдадут на метал это все же выход считаю в работу можно запустить
Зуб этот отломится и унесет с собой пол коробки
@@АлексейТихонов-ы9р всё таки такие детали если уж варить, то не рутилом же , хотя бы основные взяли бы коли спец электродов для напайки нет у них....
Эвольвенты нет и в помине....
Цена ремонта копейки , отремонтировать можно ещё и ещё
Hola buena con que electrodo se rellenó piñones des de Sudamérica Perú
Muito bom! Ficou perfeito.🇧🇷
Great job 👍
What kind of rod did he used for a welding ?
He used a steal rod..
@@jktechnology786 I meant what kind or which number .
Sorry sir I doesn't remember the exact number.... I am just a film maker
@@jktechnology786 thank you,cos it's very important .
Is it citodor?welding rod.machinable.
Техника безопасности конечно на высоте
I mean everyone is criticizing, but what about if he would re-harden the gear?
Ewolwenta? Komu to potrzebne, a do czego?
Você é um artista, parabéns. Abraços do Brasil
Wow! It took less than 8 minutes.
Que soldadura le meten a los engranes
Assalamualaikum Bhai ye shop kis jaga hai
taxila wah cantt
You are very good 👍👍👍👍👍👍👍
Técnica de habilidad y precision
Quizá tengas desconocimiento técnico,pero debo decirte que es un MAMARRACHO ese trabajo vergonzoso
SEI UN ARTISTA👏👏👏👏👏👏👏👏👏👍👍👍👍👍👍👍🇸🇲
I don't know how long it'll last but I guess gotta do what you have to do. The welding isn't as good as the lathe work but nice job. Doesn't happen in the US.
Creo que sucede en ese lugar😂😂😂😂. Es lamentable
Amigos buen trabajo, que tratamiento térmico realizan al diente que reconstruyeron, para endurecerlo?
I don’t usually comment but I couldn’t stand seeing all this misinformation.
More than one tooth make contact. So long as it’s there as a “placeholder” I think it’ll work for long time. It’s definitely a harder tooth than most would think.
If you’re thinking about it, try it!
Very nice repair.......
Bardzo świetnie jest to zrobione i jestem w pełen podziwu pozdrawiam twórcę tego filmiku serdecznie 👍👍👍👍
długo nie pojeździ. zmieniona struktura materiału tzw. "heat zone", brak jakiegokolwiek wyżarzania normalizującego lub odpuszczania materiału po wytworzeniu naprężeń, nie nawęglono (nie zastosowano również innej metody wzmocnienia materiału np. azotowanie). typowa garażowa robótka byle coś działało. ten film jest raczej z gatunku jak nie należy naprawiać części maszyn
@@andrzejskupien8391 No tak się stym zgadzam bo twórca tego filmiku powinien to jakoś utwardzić pozdrawiam serdecznie 👍
KNS100 elettrodo?👋
number of electrod ? like 👍
Donde tienes las gafas de seguridad
Also hut ab vor dem Mann gutes Auge gutes Händchen sehr geschickt und Ausführung 1a. Kann man glaube ich nicht besser machen.
Impresionante trabajo !!!!!!💯💯💯💯👏👏👏👏👏👏👏
Welding rod konsa hi
Steel rod....
Impresionante...WOW
+30 моточасов шестерне добавил:))
I think for small repairs is ok
My man, you make all the professionals repair looks like a joke
Это Пакистанцы, какая нахрен безопасность?)
Awesome work
But it will fail again because the new welded metal isn't properly being hardened, so it's soft and will wear off soon.
Exlent bro
tnku sir❤️
this works maybe as a one time fix but the way you sanded down all the teeth just to make them even will wear it with repeated repair. also the welds were pulsed instead of strung which makes me question the integrity
Maestro que maravilla
Koe bta Sakta ha ya Bhai sab kdr milain ga
Taxila
Gud job dear
❤️❤️😻
기술자들!Good!
क्या बेल्डिंग किया हु सामान गाड़ियों में सही ढंग से काम करता है और टिकाऊ भी होता है
And someone wants to continue to use it? After all, this tooth has a different strength from the rest of the teeth, a different grade of steel, a different hardness ... Probably only Kamikaze will use this gear ...
Hay quá bạn ơi
When you're in a bind what ever it takes was a very well done job
And yes you have a point but some time got to go for broke lol
If they know what they're doing, they've got the right filler rods
Без закалки это только образец
Good Mek
WHAT IS ONE!
Зуб как родной
Kindle mobile no b share Kia karainn
0312 5395972
Техника безопасности слышал? Не неслышал!
Требования безопасности и охрана труда. Понятия "Техника Безопасности" уже как бы не существует.
@@StaPerRa ну болгаркой без очков можно без глаза остаться
Perfekt robota.
Bravissimo!
Ni los alemanes saven hacer estos trabajos que lastimosamente
Good for 1 trip
Zabar 10
❤️❤️😻
This is not like fixing a hole in a pot, will not last.
Here we go , another bodge , poor welding , heat treatment lost on surrounding teeth , I wonder how long it lasted , its not often economical to repair gears
Unless you need to sell your truck.
Unless your truck is cheaper than a new gear from abroad
after all, a valuable comment, not a blind delight at this poor performance
If you cannot get the parts easily 🤷🏼♂️. I’m the USA we toss stuff that others Would consider excellent things to fix or Continúe using.
@@Jeversonapilz lo 0
استاد جی کی ورک شاپ کہاں ہے ؟
taxila
Weldon gee
Good
This is gear repair
Ok very good
Thanks you
👍👍😍😍
Молодецы
Das ist Murks. Und auch nicht gehärtet. Und einen normalen Messschieber verwendet man nicht zum anreißen.😱😱😱😱😱😱😱 Viele Grüße aus Germany
Existen soldaduras que quedan endurecida como si fueran templadas investiga y veras
Bonsoir mais ils n'attendent que vous pour leur trouver une meilleure solution ne vous gênez surtout pas pour aller leur montrer de quoi vous êtes capable dans leur condition de vie !
This is good for a laugh at least
👍👍👍👍👍
일은 잘했다.그러나 열처리는?
It became stronger then an egg
👏👏👍
Rất tốt
using cutting blade to grind... smh
👌👌
ne verujem da ce taj zub dugo da traje
Artysta.
It won't last 10 miles
Скоро во всех СТО России...
Trud uzalud
Kenapa tidak tahan lama atau tahan lama
Gigi ger dilas ga tahan lama
Это хирная это не для велоципед
that's crazy
สุดท้ายก็แตกเหมือนเดิมเชื่มแล้วเจียรยังไงก็ไม่อยู่
Халтура, кустарщина !!!!точность изделия равна сторонам света !!!!