This must be the stupidest thing I've witnessed in at least a month or more. If you are going to spend the time and effort anyway, why not simply fix the problem causing the warning instead of disabling the warning? What you have done is akin to removing the battery from a smoke detector instead of extinguishing the fire. It would have been easier just to replace the bad LED strip.
Congratulations, you figured out how to bypass the protection circuit, when you have a blown LED. Wouldn't it be better to replace the shorted out LED and not risk a fire.
@@ryderordiebrand8179 why does he deserve credit ?? All he has done is a botch it job and turned into a ticking time bomb. Bypassing the protection circuit causes the LED driver control chip to keep drawing more and more voltage until either the driver control chip can’t take no more voltage through it and pops or the power supply is under so much extra load that it fails. My Sony Bravia XE20 LED TV has started doing the 6 blinking lights issue and at the same time developed a darker shadow in the middle running vertically through the panel and hopefully it’s getting repaired under the warranty but I would be pissed if the engineer just bypassed the protection circuit and didn’t actually fix the issue correctly as it will only fail again in the near future.
@@KyleSand so that whot he was doing that is dengerous??. I have sony kdl 40w605b and it blinks 6 times i turn on tv without the screen only leds and its Ok No blinking. And only when I turn on with screen i blinks 6 times again. Please help. Maybe its broken inventer??
@@Przebudzony not sure, might be a panel short, remove one of the ribbons at a time to the panel to see if you can isolate which half is shorted if that is the case.
A 6flash of the red standby led on any Sony tv is a result of the led baclights failing , one or more of the leds on the led backlight strips has gone open and the current sensing circuit in the power supply has detected this fault , as a backlight error , BL-ERROR command usually is an active high command (logic high ) from the power supply is sent to the main board to shut the tv / power supply down , what he has done is shorted this command to ground via the the tracks on the circuit board disabling the BL-ERROR command .Very very to have a faulty power supply / led backlight driver board .More often enough the led backlights fail .
Have you ever thought of using a soldering iron instead of a poker?..As a technician myself, if I did work like this I wouldn't be able to sleep at night for fear of the tv catching fire when left in standby. 😯😯
KDL-40R453B HAVE DIFFERANT BOARDS FAULTS ARE SPECIFIC TO BOARD MODEL NUMBER, LOOKS LIKE YOU HAVE SHORTED SMD FUSES ON THE PSU BOARD' YOU DONT EXPLAIN , POOR VIDEO .....
6 red led blinking us bec of backlight LED strips need replacement...the TV would have switched off by itself...a few times before..or screen switched to another screen- input etc...than totally no picture. Try...replacing backlight strips...Bec it is a Backlight LED Strip problem...one set backlight LED strips is about $20...difficulty is Average..careful removal and recording of all screws etc to replace exactly the same way is important...Also best to replace the whole set of LED strips..don't do onlybthe Spoilt ones...bec they work in synchronization...any small voltage difference can cause a shutdown.. Use youtube videos that show how to do it as a guide...takes about 2 hours to get to the strips..if untrained...make sure the TV is switched off ...for more than 24 hours...and press switch on when unpugged to discharge as muchbas possible....and don't touch the capacitor..HIGH VOLTAGE SHOCK danger!!!
Estoy viendo y de ésa manera aprendo; 🎉❤!!!cuánto modelos de Sony Brahvia!!! enorme debe ser la cantidad, también el tamaño de pantalla, gracias por su video, gracias. Desde Guatemala 🇬🇹 City Guatemala estoy viendo su video. 🎉🎉😊😊
Be careful taking off the back cover, I accidently pulled the electrical wire off the circuit board. Had to have a friend solder it back. Other than that this fix worked great. TY!
This must be the stupidest thing I've witnessed in at least a month or more. If you are going to spend the time and effort anyway, why not simply fix the problem causing the warning instead of disabling the warning? What you have done is akin to removing the battery from a smoke detector instead of extinguishing the fire. It would have been easier just to replace the bad LED strip.
Sir sa akin di n lumalabas sony on/off agad pareho din kaya yan nyan?thanks
in advance!
Angelito Legaspi yes
@@c8productions Thank you boss. Good Bless.
Congratulations, you figured out how to bypass the protection circuit, when you have a blown LED. Wouldn't it be better to replace the shorted out LED and not risk a fire.
Give him credit, he didn't just figure it out he did it. I mean good shit!
@@ryderordiebrand8179 why does he deserve credit ??
All he has done is a botch it job and turned into a ticking time bomb. Bypassing the protection circuit causes the LED driver control chip to keep drawing more and more voltage until either the driver control chip can’t take no more voltage through it and pops or the power supply is under so much extra load that it fails.
My Sony Bravia XE20 LED TV has started doing the 6 blinking lights issue and at the same time developed a darker shadow in the middle running vertically through the panel and hopefully it’s getting repaired under the warranty but I would be pissed if the engineer just bypassed the protection circuit and didn’t actually fix the issue correctly as it will only fail again in the near future.
This is like a popular model of Samsung TV I see all the time. un58H5202. LEDs start going and then the power supply overheats and blows
@@KyleSand so that whot he was doing that is dengerous??. I have sony kdl 40w605b and it blinks 6 times i turn on tv without the screen only leds and its Ok No blinking. And only when I turn on with screen i blinks 6 times again. Please help. Maybe its broken inventer??
@@Przebudzony not sure, might be a panel short, remove one of the ribbons at a time to the panel to see if you can isolate which half is shorted if that is the case.
Bastava dissaldare il secondo piedino dell integrato. Se la tv inizia a lampeggiare, dal menù diminuire l'intensità della retroilluminazione
هاذا الشرح قد يتسبب في اتلاف الاي سي طريقة غير صحيحة
ไม่ควรเปิดเสียงดนตรี เาลารีวิวน่าลำคานมาก
Stop playing music instead explain what you were doing barrage video.
A 6flash of the red standby led on any Sony tv is a result of the led baclights failing , one or more of the leds on the led backlight strips has gone open and the current sensing circuit in the power supply has detected this fault , as a backlight error , BL-ERROR command usually is an active high command
(logic high ) from the power supply is sent to the main board to shut the tv / power supply down , what he has done is shorted this command to ground via the the tracks on the circuit board disabling the BL-ERROR command .Very very to have a faulty power supply / led backlight driver board .More often enough the led backlights fail .
I need to concentrate. The music just throws me off.
Have you ever thought of using a soldering iron instead of a poker?..As a technician myself, if I did work like this I wouldn't be able to sleep at night for fear of the tv catching fire when left in standby. 😯😯
Dude, clean your screen!
KDL-40R453B HAVE DIFFERANT BOARDS FAULTS ARE SPECIFIC TO BOARD MODEL NUMBER, LOOKS LIKE YOU HAVE SHORTED SMD FUSES ON THE PSU BOARD' YOU DONT EXPLAIN , POOR VIDEO .....
You short the 3 or 4 outputs together then the ic can’t ref that 1 channel is low they will all be the same
Would you explain it,is there resistor or fuse broken?which circuit did you connected?
Ganito din po tv nmin...anu po dahilan bat nagganyan?at magkno po kaya pag pinaayus..tia.
6 red led blinking us bec of backlight LED strips need replacement...the TV would have switched off by itself...a few times before..or screen switched to another screen- input etc...than totally no picture.
Try...replacing backlight strips...Bec it is a Backlight LED Strip problem...one set backlight LED strips is about $20...difficulty is Average..careful removal and recording of all screws etc to replace exactly the same way is important...Also best to replace the whole set of LED strips..don't do onlybthe Spoilt ones...bec they work in synchronization...any small voltage difference can cause a shutdown..
Use youtube videos that show how to do it as a guide...takes about 2 hours to get to the strips..if untrained...make sure the TV is switched off ...for more than 24 hours...and press switch on when unpugged to discharge as muchbas possible....and don't touch the capacitor..HIGH VOLTAGE SHOCK danger!!!
Why the crappy music and NO explanation of what you're doing?
Jus connect that three lines on board is that correct , i have just know same problem, but also somthind is hearing from inverter board.
sunod adlaw ana daot na pud,dilikado ang panel sa imong lamesa bay,palitan mo nalang yan ng backlight lahat...
izin tanya, tv saya pake cara itu bisa normal lagi tp selang beberapa hari kembali protect lagi led kedip , kira2 yg perlu dicek apanya ya?
ganyang ganyan din po sira ng tv namin. Magkano po kaya pagawa ng ganyang sira?
Case nung akin nggreen tpos mea onti ngred na ngbblink ng 6x. Continuous yon kpg nksaksak every 10 sec ngbblink xa ng 6x. Repair ba talaga?
Anong dahilan bkit xa ngkakaganyan?
Would anyone please tell me if there are any other side effects in the future after doing this bypass jumper work?????
Sair very nice hamra problem solution ho gaya he
dikado ang pagrepair mo ....buti di nabasag panel mo..tsk tsk..
Thank you. It works❤️
Magkano kaya paayos ka ganitong sira..??baka kasi overpriced nmn ibigay sa amin..sana masagor
It's working my tv ready with his idea thankyou
Sir sony 46ex520 6time blinking a raha he
Ganyan dn sa akin Master BD9423EFV IC pa help nmn master
San po location pagwa po sna ako
Kd65xe8505 6x Red led can you help me?
Good job
Estoy viendo y de ésa manera aprendo; 🎉❤!!!cuánto modelos de Sony Brahvia!!! enorme debe ser la cantidad, también el tamaño de pantalla, gracias por su video, gracias. Desde Guatemala 🇬🇹 City Guatemala estoy viendo su video. 🎉🎉😊😊
Pctp😊
Lasciato stare ste cazzate non hai ne meno saldatrice come si deve , 👎
What is the issue or problem if we get 6 red led indication ?
Bro pag 40 inches ba sa pin 32 rin ba dapat nka ground same sa 32 incjes
Thankyou bro
I have fix my tv
Boss gagana yang ginawa mo pero do Yan tatagal mas mabuti magpalit Ng backlight strips na bago tatlo yon ang tama
Merci beaucoup
yung amin ganyan din red light agad anong cause bakit nag red light
Goodwork it works i practically repaired one
Why does this problem occurs?
Very unprofessional
Magkano kaya magaganastos sa Repair shop ?
see what ? no words.
Thanx for video..
I made my television that way and it worked. Thank you
Good job sir
RESPECT nice I got it right
weed
Salamat sa tutorial idol may natutonan na ako
Thank sir ji
Be careful taking off the back cover, I accidently pulled the electrical wire off the circuit board. Had to have a friend solder it back. Other than that this fix worked great. TY!
Pangmatagalan po ba yan o temporary lang
Nice work
Nice one master.. Tnx for sharing.. Watching DAS-ELECTRO TECH.
I’ve just been quoted £165 to fix is that good ?
Did they replace all led?
I paid £250 apparently all led have been changed. Would be nice to know if I've been shafted
thanks
Ok boss salamat sayo.
Legit yung tinuro mo salamat.
This video was horrible... explained nothing!
Backjob for sure