Check your outlet filters, clean out. The machine will not spin if the filter is blocked. Also check your inlet into the machine. Clean screens on both ends of the pipes. Refit carefully
Assalamu alaikum I have whirlpool full automatic machine when I start on display appear,,press start to enter demo,,,no any touch.no start machine. How I can solve this 🤔
A “CE" error code on a Whirlpool Calypso washing machine indicates a "communications error.” This shows a fault preventing one or more components from reporting normal operating parameters to the machine controller. When this happens, the CE light flashes, the unit beeps once and the motor stops. Power unit down by turning off the circuit breaker or unplugging for one (1) minute. Power unit up by reconnecting power. Restart a new cycle. Monitor the washer for one (1) minute to ensure the error code does not display again.
EA Water level sensor failure or washer is overfilling Check/ Repair The EA error code appears when the electronic control board detects an errant or overflow signal from the water level sensor. If the error code appears when you try to start a cycle and the washer doesn't fill with water, unplug the laundry center and check the wire harness connections between the electronic control board and the water level sensor. If the wiring connections are tight and wires show no obvious signs of damage, replace the water level sensor because the electronic control board is indicating the sensor has failed. If the error code continues after replacing the water level sensor, replace the electronic control board because it isn't detecting the water level sensor signal correctly. If the washer fills and then the EA error code appears, the electronic control board likely detected an overflow signal from the water level sensor. When the control board detects this signal, the control stops the washer and runs the drain pump until water drains to 9.75-inches from the bottom of the spin basket or 3.5 holes from the top of the basket. The drain pump then stops and the lid remains locked. Unplug the laundry center and check to see if the tub continues to fill with water. If it does, shut off the water supply and replace the water inlet valve assembly because an inlet valve is stuck open. If the washer tub doesn't continue to fill with water, replace the water level sensor because it has likely failed. If the problem continues after replacing the water level sensor, replace the electronic control board because the control board isn't detecting water level sensor signals correctly. Possible parts Water level sensor, inlet water valve assembly, electronic control board
The "E11" error occurs when the washer takes too long to fill with water. After a set amount of time, the washer stops filling and will automatically drain if not enough water has been added Ao check the pressure in water tap...if enough or not
For your Samsung washer to work correctly, the load in the washer and the washer itself needs to be balanced. If your Samsung washer is displaying a UB error code, it means the washer is detecting it is not balanced. Often the UB error code can be resolved by rebalancing the load in the washer or checking that the washer is level. However, if the error code persists, the washer may have a defective part that will need to be replaced. The UB error code is similar to Samsung error codes U6, UE, 1 Ub, and 1U6. This guide applies to most Samsung models, including the following: 592-49045 592-49075 592-49082 592-49087 WF203ANSXAX WF206ANSXAA WF206ANSXAC WF206BNWXAC WF210ANWXAA WF218ANBXAA WF218ANWXAA WF219ANBXAA WF219ANWXAA WF220ANWXAA WF328AAGXAA WF328AARXAA WF328AAWXAA WF330ANWXAA WF340ANGXAC WF340ANRXAC WF350ANWXAA What Causes the UB Error Code? The most common causes of the UB error code are: Items in the tub have clumped together or are tangled up The washer is overloaded There are only a few items in the washer The washer is not balanced To resolve the UB error code and get your washer working again, the first thing to check is the laundry load. Check the Laundry Load The easiest solution to the problem is to open the washer and adjust the load. If the laundry is tangled or bunched up, or stuck to one side, correcting this will often resolve the issue. Overloading or underloading can also cause the error, so another easy solution is to either remove or add an item or two to the load to balance it out. Clothing items with strings or laces from shoes can also cause the error if they get caught in a part of the drum or agitator. To ensure this doesn’t happen, use a washing machine-safe bag or secure the strings so that they cannot get caught in the washer. It is also important to ensure you use the right cycle when using the washer. Each wash cycle is designed to wash specific fabric types and soil levels. If the washer is expecting a different type of load, it may think that the washer is unbalanced and display the UB error code. Once the weight of load has been rebalanced, the error should be resolved, and the washer will continue with the cycle. Reset the Washer If you have rebalanced the load but the UB error code remains, the next thing to try is to reset the washer. Sometimes an error code is caused by a control board glitch. If there is a glitch, disconnecting the washer from the power for five minutes will allow the control board to reset. If it is just a glitch, the error code should be gone when you reconnect the power to the washer. However, resetting the washer like this may also just postpone the inevitable. If the error code returns, it is important to take the time to fix the issue, as putting it off will likely lead to more serious issues in the future. Check That the Washer Is Level Another cause of the UB error code is that the washer is not sitting level on the floor. The washer may have been moved recently, perhaps if you just installed the washer or if it has been moved to a different location. However, the washer can also become unbalanced over time because of the vibrations produced by the machine during a spin cycle. Using a level tool is the best way to check and fix the issue. If the level tool shows you the washer is not level, the washer’s legs should be adjusted until the washer is level. To adjust the leveling legs, locate the locking nut on the leg and loosen it with a wrench. Then turn the leg clockwise to lower the leg or counterclockwise to raise the leg. Adjust the legs until the washer is level. When you have verified that the washer is level, tighten the locking nuts to lock them into place. Along with the washer needing to be level, the four leveling legs also need to be firmly on the floor to provide stability when the washer spins. If the floor is too slippery to keep the washer balanced, place non-skid pads under the legs to prevent the washer from moving during the cycle. The locking nuts that lock the legs in place also need to be tight against the base of the washer. Use a wrench to ensure that the locking nuts are tightly secured. Other Less Common Causes Shock Absorbers If you have a front-loader washer, it likely has one or more shock absorbers located between the outer tub and base frame of the washer. Check that the shock absorbers are connected at both ends and that one of them is not leaking fluid. Suspension Springs Both front- and top-loader washers usually have suspension springs to reduce vibrations and ensure the washer works correctly. The suspension springs can either be found beneath the tub or above the tub, holding the tub above the base. Make sure the springs are connected and in good condition, as a defective spring could be causing the UB error code. Dampening Straps Some top-loaders have four rubber straps holding the tub to the four corners of the machine. If one of these fails, the tub would be off-balance, which would trigger the UB error code. Driver Bearings If you have a front-loader washer, it may have ball bearings between the tub spindle and the motor shaft. If the casing wears and one or more of the bearings become dislodged, the tub will vibrate and could cause the UB error code. If the bearings are worn, you will likely need to contact a trained professional to replace the bearings or even think about buying a new washer. Snubber Ring The snubber ring provides a cushion for the tub of a top-loading washer. If the snubber ring wears out, the tub will make contact with the metal base and potentially cause an unbalanced load error. The snubber ring is located between the leg and the dome assembly. Dust on a plastic snubber or clumps on a felt one are signs of wear. Control Board The washer’s control board sends and receives electronic signals to operate the washer. If the above solutions have failed to fix the UB error code, the washer may have a faulty control board, which will need to be replaced.
We have whirlpool lps680gr washing machine . Error is EA . Do you have any solution with these thank you sir
Check your outlet filters, clean out. The machine will not spin if the filter is blocked. Also check your inlet into the machine. Clean screens on both ends of the pipes. Refit carefully
How about Ed1
www.justanswer.com/appliance/cyhup-whirlpool-washing-machine-ed1-error-code-fix.html
ruclips.net/video/7m85_cj1hws/видео.html
Watch this if your washer brand is LG.
Ed1 what is the meaning
Please send me the picture or a video clip on my Instagram
instagram.com/xhaamir
So i can answer you well
EA1 ERROR FOR WHIRPOOL FRONT LOAD. what's the possible problem? thanks
how about e4 error even the lid is close, it doesn't drain all the waters. before it totally drained the e4 error occurs.
Check Water level sensor...
Assalamu alaikum I have whirlpool full automatic machine when I start on display appear,,press start to enter demo,,,no any touch.no start machine. How I can solve this
🤔
Create a vid clip nd send me on Instagram
Xhaamir
What is EC6 error for whirlpool WWEB8503BW?
you can check the sensor of the drying system.
Ec6是什麼問題?
f-17 mean?
Check if the inlet water 💦 supply is low...
Turn the water tap on fully...
Clean filters too
F17 = Fault detection with mains voltage out of range.Please check the power line voltage conditions.
What is u4 code error whirlpool front load
send me picture of error or a clip while using washing machine on instagram/xhaamir
i'll try my best to help you out. Thanks
How about EC?
A “CE" error code on a Whirlpool Calypso washing machine indicates a "communications error.” This shows a fault preventing one or more components from reporting normal operating parameters to the machine controller. When this happens, the CE light flashes, the unit beeps once and the motor stops.
Power unit down by turning off the circuit breaker or unplugging for one (1) minute.
Power unit up by reconnecting power.
Restart a new cycle.
Monitor the washer for one (1) minute to ensure the error code does not display again.
What about E5 error
Hi asking what if po EA Ang lumalabas ..whirlpool po Ang brand tnx u po
EA
Water level sensor failure or washer is overfilling
Check/
Repair
The EA error code appears when the electronic control board detects an errant or overflow signal from the water level sensor. If the error code appears when you try to start a cycle and the washer doesn't fill with water, unplug the laundry center and check the wire harness connections between the electronic control board and the water level sensor. If the wiring connections are tight and wires show no obvious signs of damage, replace the water level sensor because the electronic control board is indicating the sensor has failed. If the error code continues after replacing the water level sensor, replace the electronic control board because it isn't detecting the water level sensor signal correctly. If the washer fills and then the EA error code appears, the electronic control board likely detected an overflow signal from the water level sensor. When the control board detects this signal, the control stops the washer and runs the drain pump until water drains to 9.75-inches from the bottom of the spin basket or 3.5 holes from the top of the basket. The drain pump then stops and the lid remains locked. Unplug the laundry center and check to see if the tub continues to fill with water. If it does, shut off the water supply and replace the water inlet valve assembly because an inlet valve is stuck open. If the washer tub doesn't continue to fill with water, replace the water level sensor because it has likely failed. If the problem continues after replacing the water level sensor, replace the electronic control board because the control board isn't detecting water level sensor signals correctly.
Possible
parts
Water level sensor, inlet water valve assembly, electronic control board
What about ea1?😢
How to solv E11 erer
The "E11" error occurs when the washer takes too long to fill with water. After a set amount of time, the washer stops filling and will automatically drain if not enough water has been added
Ao check the pressure in water tap...if enough or not
ano po ung ed2 error?
Please provide more details like model no. Of your washer etc.
Send a picture of the machine and one for model and a picture with the error too... please send on instagram.com/xhaamir
Ed2 error code on Whirlpool model WVTD1050AHG
@@issyafiqzulkifli6829 Clean drain hose, filter, check if drain pump working or not
Change drain pump
E 1 ERROR PO ANU MEANING?
E1 Error code means the correct water level has not been reached within 20 minutes of the washer starts.
PAG U4 PO NAKALAGAY ANO MEANING?
Door lock or door switch problem
@@repairingschool May fix video po ba kayo na nagawa na doon? Paano po gagawin namin help po
Use English my Friend.
@@repairingschool do u have a fix video for that problem? We badly need help sir
@@lancez4884 come on Instagram...
Insta/xhaamir
Send a video there with the model. Let's se what we can do.
Ub error
For your Samsung washer to work correctly, the load in the washer and the washer itself needs to be balanced. If your Samsung washer is displaying a UB error code, it means the washer is detecting it is not balanced. Often the UB error code can be resolved by rebalancing the load in the washer or checking that the washer is level. However, if the error code persists, the washer may have a defective part that will need to be replaced. The UB error code is similar to Samsung error codes U6, UE, 1 Ub, and 1U6.
This guide applies to most Samsung models, including the following:
592-49045
592-49075
592-49082
592-49087
WF203ANSXAX
WF206ANSXAA
WF206ANSXAC
WF206BNWXAC
WF210ANWXAA
WF218ANBXAA
WF218ANWXAA
WF219ANBXAA
WF219ANWXAA
WF220ANWXAA
WF328AAGXAA
WF328AARXAA
WF328AAWXAA
WF330ANWXAA
WF340ANGXAC
WF340ANRXAC
WF350ANWXAA
What Causes the UB Error Code?
The most common causes of the UB error code are:
Items in the tub have clumped together or are tangled up
The washer is overloaded
There are only a few items in the washer
The washer is not balanced
To resolve the UB error code and get your washer working again, the first thing to check is the laundry load.
Check the Laundry Load
The easiest solution to the problem is to open the washer and adjust the load. If the laundry is tangled or bunched up, or stuck to one side, correcting this will often resolve the issue. Overloading or underloading can also cause the error, so another easy solution is to either remove or add an item or two to the load to balance it out.
Clothing items with strings or laces from shoes can also cause the error if they get caught in a part of the drum or agitator. To ensure this doesn’t happen, use a washing machine-safe bag or secure the strings so that they cannot get caught in the washer.
It is also important to ensure you use the right cycle when using the washer. Each wash cycle is designed to wash specific fabric types and soil levels. If the washer is expecting a different type of load, it may think that the washer is unbalanced and display the UB error code.
Once the weight of load has been rebalanced, the error should be resolved, and the washer will continue with the cycle.
Reset the Washer
If you have rebalanced the load but the UB error code remains, the next thing to try is to reset the washer. Sometimes an error code is caused by a control board glitch. If there is a glitch, disconnecting the washer from the power for five minutes will allow the control board to reset. If it is just a glitch, the error code should be gone when you reconnect the power to the washer. However, resetting the washer like this may also just postpone the inevitable. If the error code returns, it is important to take the time to fix the issue, as putting it off will likely lead to more serious issues in the future.
Check That the Washer Is Level
Another cause of the UB error code is that the washer is not sitting level on the floor. The washer may have been moved recently, perhaps if you just installed the washer or if it has been moved to a different location. However, the washer can also become unbalanced over time because of the vibrations produced by the machine during a spin cycle.
Using a level tool is the best way to check and fix the issue. If the level tool shows you the washer is not level, the washer’s legs should be adjusted until the washer is level. To adjust the leveling legs, locate the locking nut on the leg and loosen it with a wrench. Then turn the leg clockwise to lower the leg or counterclockwise to raise the leg. Adjust the legs until the washer is level. When you have verified that the washer is level, tighten the locking nuts to lock them into place.
Along with the washer needing to be level, the four leveling legs also need to be firmly on the floor to provide stability when the washer spins. If the floor is too slippery to keep the washer balanced, place non-skid pads under the legs to prevent the washer from moving during the cycle. The locking nuts that lock the legs in place also need to be tight against the base of the washer. Use a wrench to ensure that the locking nuts are tightly secured.
Other Less Common Causes
Shock Absorbers
If you have a front-loader washer, it likely has one or more shock absorbers located between the outer tub and base frame of the washer. Check that the shock absorbers are connected at both ends and that one of them is not leaking fluid.
Suspension Springs
Both front- and top-loader washers usually have suspension springs to reduce vibrations and ensure the washer works correctly. The suspension springs can either be found beneath the tub or above the tub, holding the tub above the base. Make sure the springs are connected and in good condition, as a defective spring could be causing the UB error code.
Dampening Straps
Some top-loaders have four rubber straps holding the tub to the four corners of the machine. If one of these fails, the tub would be off-balance, which would trigger the UB error code.
Driver Bearings
If you have a front-loader washer, it may have ball bearings between the tub spindle and the motor shaft. If the casing wears and one or more of the bearings become dislodged, the tub will vibrate and could cause the UB error code. If the bearings are worn, you will likely need to contact a trained professional to replace the bearings or even think about buying a new washer.
Snubber Ring
The snubber ring provides a cushion for the tub of a top-loading washer. If the snubber ring wears out, the tub will make contact with the metal base and potentially cause an unbalanced load error. The snubber ring is located between the leg and the dome assembly. Dust on a plastic snubber or clumps on a felt one are signs of wear.
Control Board
The washer’s control board sends and receives electronic signals to operate the washer. If the above solutions have failed to fix the UB error code, the washer may have a faulty control board, which will need to be replaced.