0:54 "lets get this out onto a tray... Nice!" Incredible build! I really like the fact that with you thumbnails that seem to be cickbait acutally aren't
Between you and Kev Talbot I cannot get enough of your videos! Raz you inspired me to build my speed car! I’ve started with a carbon / alloy TT01 chassis with a hobbywing wing max10 esc and motor combo and slowly been tightening the car up and adding aero to it while using a Mercedes CLK GTR body where I’ve then 3D printed a air intake box that fits over my twin cooling fans and has a real working air intake from the roof scoop of the body shell
I don’t know if you know but you’re not the first. My boy has been waiting for you to post this video so he can show his four motor car! And has been working on a 6 motor car that’s almost finished. Stay tuned seriously !
With this number of motors it may be interesting to see if there is a way to sync the motors in a more precise way. They are all sensored right? How cool would it be if there was a control module that regulates all esc's at the same time for perfectly aligned timing
Probably depends on cable length. Unless raz can get everything placed at the perfect distance, I’m not sure if it’s possible to get them to sync. My vision is the longer the cable from the receiver to the esc, the more the delay is. U gotta think, first it has to wirelessly send a connection from the transmitter to the receiver, then the receiver has to send the power through both the Y leads; then the esc has to process it, then the esc has to send that to the motor; then depending on if raz uses direct drive, or a pinion, still it has to go through the slop of the pinion, then to the spur, spur sends power to transfer case, then it divides it to the driveshafts keep in mind those have a little bit of slop in to them, then the drive pins have to spin the hexes, the hexes spin the wheels, THEN after all that the car gets power. So I’m my opinion, no matter what setup he uses, there will probably be about a half second of delay from the time the trigger is pulled, to the time the car moves. Servos are fine tho, cuz it’s a lot less complex. So yeah that’s my take on it. Could be completely wrong but hey I gave it a shot
@@endosrc Good point but I didn't mean something like a flightcontroller in the open loop system between the reciever and esc's but on the closed loop end where the esc's selfregulate based on the sensor measurement input.
Raz, I'm glad to see the traditional body on the twin engine car. It's a known and trusted quantity and capable of 190. Save the carbon body for later. It might cause more problems than you need.
AGAIN U HAVE SHOWN US THE MOST IMPORTANT PART OF DIFFS AND HOW TO SHIM THEM.THANKS BRO.A MASTER AT WORK.finally thanks to you we can all upgrade our diffs the proper way.U ROCK RAZ
I had asked you about the GP5’s and the hot racing diffs figment. Thank you for showing where you removed material because I did the same thing and eventually gave up because I had ground so much and still had issues. The fact that you produce videos with content based off of questions from previous ones really says a lot! Great video again and I look forward to the next one. 👍👍👍
Love how much detail you put into building your rigs. I usually slap it together not even giving a shit. A person who truly cares about the hobby it’s just awesome to see!
A couple days ago i didnt even know this grade of RC car was a thing hours and hours of your videos and kevins ive grown an respect for your passion. Totaly out of my orice range but the quality looks beautiful
Fun top notch video as always! Thank you! I watch every video and try to heckle my best in a loving way! I understand all the work and time you put into this and I appreciate it 🙏
I've just been and got over the excitement of the last build, now you're doing a bigger build. I'm now thinking about building a lcg slash speed car with all the information you have shared. You are the best Raz ❤️
Love the builds u make...and the buddies trying to catch up.. looks like a blast...love to make the X-01a speed car and try to catch ya...but aint got the funds like that...lol...but thanks for all the inspiration and love the videos again..cant wait to see the 60hp
Question for anyone: I have a kraton 6s exb (running on 8s, locked center diff). Problem is I've had an issue with either the front or rear diffs for a while where it clicks, is loud, and saps power. I can't figure out how to fix it. I've had all the diffs apart many times and there's no visable damage. Is it a terrible idea to just lock all the diffs? I don't race, I just bash it really hard. Appreciate any help!
Boom! I liked the dual motor 👌 now it’s a quad motor!! Your blowing my mind can’t wait to see how this works out 💪 more power but can u keep it down? And I luv the new shiny ✨ bits 😎 with the steering and the bearings 💨
I've been thinking about this car a bit more and wonder if you need thrust bearings or angular contact bearings in the diffs. It may not be a bad idea considering the enormous forces these 4 motors combined will put out The only issue with angluar contact bearings is minimum size. They are at least 10mm id/30mm od. Thrust bearings are widely available for rc because of the model helicopters.
Usually, I wouldn't care who you're friends with, or whatever. T's the content that matters. It tickles me though, to see Kevin pinned at the top. You're great entertainers, both:-) Thanks!
Thanks Raz. That car is going to be a super beast. I warn you, don't run it. With all that power it may cause the Unbalancing of the earth which could cause earthquakes, floods. When those tires grab watch out. Again thanks for taking us all along with your build. What speed are you looking for. Maybe 235 mph. Good luck
4 motors ? That’s going to be crazy ! I just did a full ceramic bearings swap on my infraction, glad to know I did the diff swap and reinstalling right. Thanks Raz for the pro tips. 👍🏼🤜🏼🤛🏼😜
I know you aren’t into crawlers but making a crawler with 4 independent motors and ESC’s would be fun. 3 gear transmissions are pretty compact. Might be a fun build
Good stuff man!!! Still keeping that rear shock thing secret? Haha. Pretty sure I've seen every one of your videos and can't seem to find the rear shock tip. Keep it up
I wanna know how you do your back shocks lol, they’re done different then what you’ve showed in the basic how to video.. I’m just curious what rubber pieces you’ve used on the outside of the shock, even without a spring. How did you do that set up?
How do you like those wera screwdrivers Raz? I love mine. The hex-plus really makes a difference imo. Concave sides bite into screws, haven't stripped any since using these
Wow! I’m curious to see how you are gonna fit 4 motors. Maybe 2 facing forward and 2 facing the rear. I guess you will be the test to how strong the drivetrain really is. Might want to have some special tires made to withstand that much power as well. Guess Kev has been right all along. MORE POWA!! 💪🏻
Great stuff! Inam really curious how it turns out! Did you not put any lubricant inside the scorched locked diff? In the video it seemed like you did not before you closed it!
Everything You Need Is Here..
www.perfectpassrc.com/
more power!! you're learning!! haha
Hahaha
How much power is too much power :D Raz will tell us
Hope one of you 2 of my favorite rc guys will have the record soon,
Kevin must be so proud…😀
Guess you were right Kev. MORE POWA!!!
Really really loving and enjoying the longer “how to” build vids. Keep ‘em coming and the longer the video the better!!!
0:54 "lets get this out onto a tray... Nice!"
Incredible build! I really like the fact that with you thumbnails that seem to be cickbait acutally aren't
Between you and Kev Talbot I cannot get enough of your videos! Raz you inspired me to build my speed car! I’ve started with a carbon / alloy TT01 chassis with a hobbywing wing max10 esc and motor combo and slowly been tightening the car up and adding aero to it while using a Mercedes CLK GTR body where I’ve then 3D printed a air intake box that fits over my twin cooling fans and has a real working air intake from the roof scoop of the body shell
Speed is a question of money, how fast do you want to go ?
Me: yes
Truly looking forward to this build! 👍
I don’t know if you know but you’re not the first. My boy has been waiting for you to post this video so he can show his four motor car! And has been working on a 6 motor car that’s almost finished. Stay tuned seriously !
I hope I'm not the first lol..
Jesus it's 2021 it's not that hard to do lol
Awesome!!! This thing is going to Blast!!!! Great tips during your build too Raz!!
Basic fitter/machinist trade skills shown in vid👍
Holy shit that's insane for a RC vehicle to have that much HP / torque! Just insane! Christ on a bike, that vehicle is sick!
With this number of motors it may be interesting to see if there is a way to sync the motors in a more precise way. They are all sensored right? How cool would it be if there was a control module that regulates all esc's at the same time for perfectly aligned timing
Probably depends on cable length. Unless raz can get everything placed at the perfect distance, I’m not sure if it’s possible to get them to sync. My vision is the longer the cable from the receiver to the esc, the more the delay is. U gotta think, first it has to wirelessly send a connection from the transmitter to the receiver, then the receiver has to send the power through both the Y leads; then the esc has to process it, then the esc has to send that to the motor; then depending on if raz uses direct drive, or a pinion, still it has to go through the slop of the pinion, then to the spur, spur sends power to transfer case, then it divides it to the driveshafts keep in mind those have a little bit of slop in to them, then the drive pins have to spin the hexes, the hexes spin the wheels, THEN after all that the car gets power. So I’m my opinion, no matter what setup he uses, there will probably be about a half second of delay from the time the trigger is pulled, to the time the car moves. Servos are fine tho, cuz it’s a lot less complex. So yeah that’s my take on it. Could be completely wrong but hey I gave it a shot
@@endosrc Good point but I didn't mean something like a flightcontroller in the open loop system between the reciever and esc's but on the closed loop end where the esc's selfregulate based on the sensor measurement input.
Seeing this video I was thinking of a dual Northstart Cadillac and getting them to sync.
RC PORN🤣🤣🤣 AWESOME AS ALWAYS!!
Do you have link for the diff case
My bad 😞. Should have know 😂😂
Nice job Ruz, I'm loving it
Dope can’t wait to see it finished
Raz, I'm glad to see the traditional body on the twin engine car. It's a known and trusted quantity and capable of 190. Save the carbon body for later. It might cause more problems than you need.
Man put wings on it Call it The Razzell Dazzell
This video was amazing raz loved it bro massive fan buddy
Congrats on the 50k man!!! 🤘
AGAIN U HAVE SHOWN US THE MOST IMPORTANT PART OF DIFFS AND HOW TO SHIM THEM.THANKS BRO.A MASTER AT WORK.finally thanks to you we can all upgrade our diffs the proper way.U ROCK RAZ
These videos are great. Thanks for exploring these wild rc fantasies🤙
Raz, u lost your mind! And i love it!
love that you share all your knowledge, Thank you so much man really!
Dame . You crazy guy. 🤪 love it
💯
😲😲😲😲lol more!!!keep it up💪 100hp🎉🎉🎉😆I love your videos I leaned so much from you thank you🤘
I had asked you about the GP5’s and the hot racing diffs figment. Thank you for showing where you removed material because I did the same thing and eventually gave up because I had ground so much and still had issues. The fact that you produce videos with content based off of questions from previous ones really says a lot! Great video again and I look forward to the next one. 👍👍👍
Crushing it,Thanks for the footage 🤙🔥🔥
Love how much detail you put into building your rigs. I usually slap it together not even giving a shit. A person who truly cares about the hobby it’s just awesome to see!
Holy Cow my friend! :) We never really know what to expect next... ;)
i like your videos..thanks for taking the time to do it step by step instead of fast fwd the actual tutorial
Mind bending!!!! 💪🏾💯💪🏾
A couple days ago i didnt even know this grade of RC car was a thing hours and hours of your videos and kevins ive grown an respect for your passion. Totaly out of my orice range but the quality looks beautiful
That's goin to be insanely fast can't wait to see it running 👍❤️'n the build series 👍👍👍
I could watch the smoothness for hours of those bearings
DUDE... LIKE...WOW... I LOOOVE IT! INSANITY.🤯💯❤
Superb, first video where i can perfectly see how to properly set the shims. Thank you.
Fun top notch video as always! Thank you! I watch every video and try to heckle my best in a loving way! I understand all the work and time you put into this and I appreciate it 🙏
Wow , what a beast. Awesome car and video 🙏
I've just been and got over the excitement of the last build, now you're doing a bigger build. I'm now thinking about building a lcg slash speed car with all the information you have shared. You are the best Raz ❤️
Thanks!!
Awesome.
Love it Raz🥰🥰🥰🥰
That will be Nuts! 🤣
Nice Tutorial, great job... 😀
Congratulations on 50k!
OMG I love this madness!!!!!
Excellent install congratulations
Love the builds u make...and the buddies trying to catch up.. looks like a blast...love to make the X-01a speed car and try to catch ya...but aint got the funds like that...lol...but thanks for all the inspiration and love the videos again..cant wait to see the 60hp
Question for anyone: I have a kraton 6s exb (running on 8s, locked center diff). Problem is I've had an issue with either the front or rear diffs for a while where it clicks, is loud, and saps power. I can't figure out how to fix it. I've had all the diffs apart many times and there's no visable damage. Is it a terrible idea to just lock all the diffs? I don't race, I just bash it really hard. Appreciate any help!
Waiting for part 2 :)!
Keep it up its gonna be a rocket
Very lovely build and AWESOME Build Video Raz! 👍👍👍 Can't wait to see how you fit 4 Motors, ESCs and the needed Batteries in ONE rig 🤷♂️ 😘
Raz, thank you for making our wild dreams come true.
WOW! 50k subscribers! Congrats and respect !!! You’re one of best in RC theme.
Thanks brother!
Do you lube the the ring and pinion gears I didn’t see any being used
RC cars are not complicated, a friend if mine once said...
this video makes it look like science :D
Damn .the RC game sure has evolved
😂👌🏼
Boom! I liked the dual motor 👌 now it’s a quad motor!! Your blowing my mind can’t wait to see how this works out 💪 more power but can u keep it down? And I luv the new shiny ✨ bits 😎 with the steering and the bearings 💨
I've been thinking about this car a bit more and wonder if you need thrust bearings or angular contact bearings in the diffs. It may not be a bad idea considering the enormous forces these 4 motors combined will put out The only issue with angluar contact bearings is minimum size. They are at least 10mm id/30mm od. Thrust bearings are widely available for rc because of the model helicopters.
I liked the smooth bearing spinning also
I love the spinning let it spin Raz let it spin 🤣👍🏽💯
I can’t wait to see what you do with this car Raz. I followed your twin motor build. Most likely will follow this 1 too
cant wait to see this beast in action. think you might to make a trailer for the batteries though lol!!!
WOW , I dont know what faster at this point . The car or you talking . LOL
Can’t wait to see how this turns out!!👍🏻👍🏻👍🏻
It’s not boring. I like hearing about all the details. Don’t speed though it.
I think a record breaking car is being built here,surely 😁
Usually, I wouldn't care who you're friends with, or whatever. T's the content that matters.
It tickles me though, to see Kevin pinned at the top.
You're great entertainers, both:-)
Thanks!
Who is going to be the first to put 6 soda cans in a car? You or Kev? 🤣🤣💯💯💯💯💯💯
(6💯's, on for each can lol)
Thanks Raz. That car is going to be a super beast. I warn you, don't run it. With all that power it may cause the Unbalancing of the earth which could cause earthquakes, floods. When those tires grab watch out. Again thanks for taking us all along with your build. What speed are you looking for. Maybe 235 mph. Good luck
Sweet
This thing is going to be absolutely insane!!!
The record holder has only 1 motor and a big development effort. With the same effort and 4 motors you would have a insane record.
Intrigued with this build...
gonna need a longer runway Raz LOL
Great content!
4 motors ? That’s going to be crazy ! I just did a full ceramic bearings swap on my infraction, glad to know I did the diff swap and reinstalling right. Thanks Raz for the pro tips. 👍🏼🤜🏼🤛🏼😜
Perfect demo of why to use Vitavon and not HR bulkheads. Leaving the cover loose OMG 😲.
This is going to be very interesting. Loving the engineering on all the custom parts.
Grease on the pinions/ring gears? Or is that coming later?
I was thinking the same thing -When is he going to grease up the ring gears?
Super
Godspeed good sir!
Raz on speed. XD
I know the chassis is from scorched but what is the front and rear suspension setup from and can you buy that separately? Thanks anyone!
I know you aren’t into crawlers but making a crawler with 4 independent motors and ESC’s would be fun. 3 gear transmissions are pretty compact. Might be a fun build
Raz shifrin where can I get the whole front and rear assembly or do I need to piece together
I wish my workbench was that clean
Are you using locker diffs because it's so much power, I'm in the middle of a build and I'm unsure what's best
Good stuff man!!! Still keeping that rear shock thing secret? Haha. Pretty sure I've seen every one of your videos and can't seem to find the rear shock tip. Keep it up
26:29 deeznuts 🤣 😂
This is going to be an epic build 😎 showing us how you set up your spools was helpful 👍
Hell yeah!! What are you up too now?! Hahahaha
I wanna know how you do your back shocks lol, they’re done different then what you’ve showed in the basic how to video.. I’m just curious what rubber pieces you’ve used on the outside of the shock, even without a spring. How did you do that set up?
How do you like those wera screwdrivers Raz?
I love mine. The hex-plus really makes a difference imo. Concave sides bite into screws, haven't stripped any since using these
When boredom and hella money collide lol 😯 mad scientist you are...
Holy shit-60hp is the same as a big bike from the 70's!!!
Raz.. would you suggest I purchase a mmx8 first build in my limitless??
Wow! I’m curious to see how you are gonna fit 4 motors. Maybe 2 facing forward and 2 facing the rear. I guess you will be the test to how strong the drivetrain really is. Might want to have some special tires made to withstand that much power as well. Guess Kev has been right all along. MORE POWA!! 💪🏻
I can't to see the next video that looks pretty crazy I have a good feeling you are going to break that 203 mph very soon
Hope you are going to set 2 up to run front wheels and other 2 to run the rear wheels
Great stuff! Inam really curious how it turns out! Did you not put any lubricant inside the scorched locked diff? In the video it seemed like you did not before you closed it!
Raz what video shows your springless rear shock setup my friend? Thanks in advance!
No grease in the diff? Or did I miss it......