how to charge the laptop battery without laptop

Поделиться
HTML-код
  • Опубликовано: 23 дек 2024

Комментарии • 171

  • @tickyul
    @tickyul Год назад +3

    That input goes through the battery-control-module before reaching the cells????

  • @eksine
    @eksine 5 месяцев назад +5

    if it shows 0.0 volts it doesn't mean the battery is empty, if it truely was that battery would be ruined. that's the battery management system shutting off discharge to protect the battery until it is charged again. if it dropped to a true 0 volt it would be dead permanently

    • @DixyPro1
      @DixyPro1  5 месяцев назад

      Yes, what you say is completely accurate. Greetings to you

  • @raptorswire7212
    @raptorswire7212 Год назад +5

    ...you can explain a little bit how do you choose correct connector points, why did you swap polarity in the middle of the video and if there is protection circuit

    • @DixyPro1
      @DixyPro1  Год назад

      The first and last points are the negative and positive points, and they are defined using an amphometer. When reading the battery level, the polarities may be reversed because the reading will not change either to the negative or to the positive. A protection circuit was installed after filming

  • @dhananjaykadam2786
    @dhananjaykadam2786 10 месяцев назад +1

    I have dell battery with 10 wire connector. Please guide how to charge battery externally. I have not found any details about this connector wiring.

    • @DixyPro1
      @DixyPro1  10 месяцев назад

      The wires in the middle supply the data, and the wires at the ends supply the power. Try all the wires using a 12 volt DC motor or a 12 volt bulb

  • @mickymannis
    @mickymannis Год назад +2

    5:35 what are the dimensions of the pins you made

    • @DixyPro1
      @DixyPro1  Год назад

      Approximately 1/2" x 1".

  • @JJLL-p2k
    @JJLL-p2k 4 дня назад

    My laptop works only with battery, not power supply. So I need to charge it like you did externally. Battery says 15.4v and a power adopter says 19v, 3.42A. How many volts and amps do you recommend?

    • @DixyPro1
      @DixyPro1  4 дня назад

      The charger must be higher than the battery, so it is better for you to have a charger of 16 to 18 volts and amperes of 2 to 5 amps.

  • @lovinglearning926
    @lovinglearning926 6 месяцев назад +2

    When I checked my laptop battery connector with adaptor plugged. It shows on 0.30 voltage. So my laptop shows only message 0% plugged in charging but actually battery doesn't get charged

    • @DixyPro1
      @DixyPro1  6 месяцев назад

      The battery is not working and needs to be replaced

    • @lovinglearning926
      @lovinglearning926 6 месяцев назад

      @@DixyPro1 1. I connected the the laptop to adopter.
      2. I removed the battery from laptop.
      3. I checked battery connector of laptop not of battery.
      4. The battery connector of laptop shows 0.30 to 0.34 voltage.
      5. I recharged battery with adaptor. Now it shows 11.1 voltage.
      6. When I start laptop with adaptor. It works.
      7. When I remove adaptor. It works on battery power but doesn't charge battery.
      8. As battery connector of laptop only shows 0.30 voltage. The laptop is unable to charge the battery.
      9. Is the battery replacement is the solution ?
      10. Or there updating BIOS will help? ( As per RUclips videos)
      11. There is problem in motherboard or the any MOSFET
      Thank you. 🙏

    • @necy_18
      @necy_18 День назад

      ​@@lovinglearning926got the same problem with u, please let me know if your laptop has already been fixed and how. Thank you!

    • @lovinglearning926
      @lovinglearning926 День назад

      @necy_18 I changed its battery now working well. It's battery problem

  • @AndraPlayz
    @AndraPlayz Год назад +2

    can you give me the name of that thing 2:09 ?

  • @kaoticwatching
    @kaoticwatching 2 года назад +27

    I don’t know why they don’t make a adapter already to do such thing…. You have to know your voltage and wats to do your way.

    • @DixyPro1
      @DixyPro1  2 года назад +1

      You are right _ 12 volts .2 amp

    • @alimajeed3570
      @alimajeed3570 Год назад

      @@DixyPro1
      How do you know which is + and wich is -?
      And, is it always the +and - on both ends of the teeth.
      Please i need the answers.

    • @alimajeed3570
      @alimajeed3570 Год назад +1

      ​@@DixyPro1
      And do i need not to forget it to long on the charger?

    • @informationsupdate9790
      @informationsupdate9790 Год назад

      How many chargers can you charge?

  • @marvinv6760
    @marvinv6760 Год назад +4

    Hi, thanks for your video! My PC has a dameged electric circuit, I need to charge my battery externally like you did. My PC needs a power of 120W, I still have the charger. Do you think I can do it and get my computer back to life again? Any further suggestion?
    Thanks

    • @DixyPro1
      @DixyPro1  Год назад +1

      Don't do this yourself. It is best to show the device to a technician

  • @Raff_Vid
    @Raff_Vid Год назад +1

    How to know if the battery is fully charge?, im afraid to overcharge it

    • @DixyPro1
      @DixyPro1  Год назад

      usually The battery is charged with a 12-volt charger, and when charging is complete, the charging process stops automatically through an automatic disconnection circuit inside the battery (Bms circuit ).

    • @Raff_Vid
      @Raff_Vid Год назад

      Ok thanks for you information.

    • @nicoindonesia1476
      @nicoindonesia1476 Год назад

      @@DixyPro1 my battery is 10.8 volt 5800 mah, what type of charger suitable ? Thanks

  • @Iamforspiritual
    @Iamforspiritual 2 месяца назад

    While checking with multimeter At 3.06 red wire is to left of screen and while chargin at 3.45 red wire is to right. Csn you explain how polarity changes

    • @DixyPro1
      @DixyPro1  2 месяца назад

      When charging the battery, the poles must be identical, but when measuring the voltage, the poles may not be identical.

  • @pwrouzaud
    @pwrouzaud Год назад +1

    Thanks for this info, and your generosity in answering questions; those answers help us all.

    • @DixyPro1
      @DixyPro1  Год назад +1

      Thank you very much

  • @seanvandiijk2889
    @seanvandiijk2889 4 месяца назад

    Thank you so much, from Argentina. I was able to jumpstart my Toshiba C-50 battery pack. This laptop has a loose lid and probably it awake from standby mode while stored on my backpack until depleted fully, regardless of hibernation or whatever settings I had.
    A tutorial was published in my blog I shared this video. The PA5024u battery I'm talking about seems to need a minimum voltage for the controller chip in order to do anything, if depleted, that circuit will prevent the battery to be charged by the charging circuit on the mainboard. So this battery is able to be jumpstarted, because I check another laptop battery from other brand that does not show any voltage in the terminals even if fully charged

    • @DixyPro1
      @DixyPro1  4 месяца назад

      The battery usually contains 6 cells. If one cell is not working, the whole battery will not work. If you can carefully open the battery and replace the bad cell, the battery will work.

    • @seanvandiijk2889
      @seanvandiijk2889 4 месяца назад +1

      @@DixyPro1 the original battery got damaged because I attempted to charge it making perforations through the plastic case and shorted circuit one of its cells and it made a small fire until the short circuit ended.
      Then i bought a replacement alternative battery and it drained fully until it wouldn't work anymore (it said fully charged but was empty)
      Finally I tried onr more time a tutorial and found this, applied 12v to the + - terminals and the whole pack had charge again. Then I put it in the laptop and the battery circuit was reset when thr orange led began to blink, there i connected the charger and it began to work normally! Thanks Gd! My laptop is my DJ rig. Thank you bro!

  • @UsuMan-uy5mu
    @UsuMan-uy5mu Год назад +1

    Can that process Be used everyday without Damaging the btry cells?

    • @DixyPro1
      @DixyPro1  Год назад

      It is best to use this method only in case of emergency

  • @jimmatrix7244
    @jimmatrix7244 3 месяца назад

    When you are charging the battery you had the positive and negative wires switched unlike while checking for voltage. Why?

    • @DixyPro1
      @DixyPro1  3 месяца назад

      This is not charging, it is just knowing the voltage only. Reversing the polarity does not harm anything.

    • @jimmatrix7244
      @jimmatrix7244 3 месяца назад

      @@DixyPro1 Thanks for the reply. Beginner here.

  • @wibowoims527
    @wibowoims527 2 года назад +2

    Infonya sangat manfaat unt cas batereai tanpa laptop.
    Bgmn cara tentukan "pin" unt pasang kabel cas?
    Sy agak bingung :
    Menit 0:11 tanda + di kanan, - di kiri.
    Menit 3:01 ukur volt dg kabel merah (+) di kiri & kabel hitam (-) di kanan. Koq terbalik?
    Menit 3:37 ngecas dg kabel merah (+) di kanan & kabel hitam (-) di kiri
    Menit 4:47 ukur volt dg kabel merah (+) di kanan & kabel hitam (-) di kiri

    • @DixyPro1
      @DixyPro1  2 года назад +3

      Terima kasih atas komentar Anda yang berharga. Saat mengukur baterai dengan ohmmeter, sisi negatif dari positif tidak terlalu penting, karena hasilnya sama, dan tanda negatif (-) muncul di layar multimeter jika sisinya berbeda. Sedangkan untuk pengiriman. Artinya, pengisian baterai, tidak diperbolehkan untuk membalikkan terminal, terminal positif harus dengan positif dan negatif dengan negatif.

    • @wibowoims527
      @wibowoims527 2 года назад +1

      @@DixyPro1
      Ok. Clear.
      Maturnuwun.

  • @AYOUB-nn6fo
    @AYOUB-nn6fo 11 месяцев назад

    I have a 14.8v laptop battery that I want to charge externally. How many volts and amps do you need?

    • @DixyPro1
      @DixyPro1  11 месяцев назад

      about 16 v / 1 or 2 amps

  • @farhanfaiz1998
    @farhanfaiz1998 7 месяцев назад

    Is there BMS ckt inside the laptop battery package?

  • @ihit2011RoboEngineer
    @ihit2011RoboEngineer Год назад

    Quick question, how many volts and amps does it require to charge it, so that I can use a charger with it?

  • @icole8647
    @icole8647 Год назад +7

    Just what I needed. Thank you champ!

  • @gloryidigu1889
    @gloryidigu1889 7 месяцев назад +1

    Is there anywhere we can get this to charge batteries without laptops?

  • @anishk.bansal4913
    @anishk.bansal4913 Год назад

    Hey my laptop charger port is damages cant put money to it so can i ise this method regularly using my laptop charger as red and black wires(by cutting out the pin). Also my the battery does not indicate (+)or (-) signs on it so how do i know which way is (+) pls help

    • @DixyPro1
      @DixyPro1  Год назад

      Hey, you . First, with regard to the charger jack, the outer part is negative and the inner part is positive. Secondly, place the avometer in the battery terminals. If the number is without a negative sign (-), this means that the connection is completely correct and that the positive terminal on the avo is the same as the positive terminal in the battery. However, if a (-) sign appears, then reverse the terminals. Thirdly, if you do not have an avo, connect it to the charger using a 12-volt motor (the inner terminal is the positive one) and observe the direction of rotation of the motor. For example, the motor turns to the right. Connect the motor to the battery. If the rotation is to the left, reverse the motor terminals until it rotates to the right. Thus, you will know the positive and negative terminals of the battery.

    • @anishk.bansal4913
      @anishk.bansal4913 Год назад

      @@DixyPro1 you say with regard to the port outer part is negative so if charger is on right side of the battery then negative one will be on the right corner(if i dont rotate the battery in any way after removing ) if i am right then just give heart no need to bother for a reply. Thanks btw

  • @joejo6273
    @joejo6273 Год назад +5

    Modern day technology on modern OEM batteries does not allow you to do this !! Its not as simple as you make it out to be.

    • @CM-xr9oq
      @CM-xr9oq 7 месяцев назад

      It depends on the BMS chip.

  • @SudamManujaya
    @SudamManujaya Год назад +1

    What terminals I want to connect bro
    Positive to positive or positive to negative

    • @DixyPro1
      @DixyPro1  Год назад +1

      Positive to positive

  • @mickymannis
    @mickymannis Год назад +1

    What amp is the power supply you used to charge the battery

  • @AmigaA-or2hj
    @AmigaA-or2hj 9 месяцев назад

    Thanks for the tip! I have a couple of dead laptop batteries that refuses to charge. I’ll try it tonight!🙏

    • @gamesblox7359
      @gamesblox7359 8 месяцев назад

      Hello! I was just wondering if it did work because I'm gonna try this and I don't wanna cause any harm to my house

    • @AmigaA-or2hj
      @AmigaA-or2hj 8 месяцев назад

      @@gamesblox7359 It worked briefly. After several hours charging, the battery wouldn’t hold its charge. I had to buy a new one.

  • @chandra_mouli76
    @chandra_mouli76 5 месяцев назад

    adaptor is 12v . right? 1a or 2 a ..

  • @dynoshane2651
    @dynoshane2651 7 месяцев назад

    How long does it take to fully charge roughly?

    • @DixyPro1
      @DixyPro1  7 месяцев назад

      You must constantly monitor the charge level by using the AVO

  • @merdas2000
    @merdas2000 Месяц назад

    Witch charger you use volt and ampers?

    • @DixyPro1
      @DixyPro1  Месяц назад

      12 v / 6 Amp

    • @merdas2000
      @merdas2000 Месяц назад

      6A ? Can show picture label of that litlle charger?to find one similar?

  • @hayathulakhbaar6221
    @hayathulakhbaar6221 Год назад

    Charging voltage?

  • @dollaz4647
    @dollaz4647 Год назад

    Is this possible without connectors? For instance I don't have any connectors and my wires are black, white and blue but my battery is similar to yours, any tips?

    • @DixyPro1
      @DixyPro1  Год назад +1

      Connectors are not necessary, but the most important thing is that there is no contact between the positive and negative terminal

    • @OmarElhatabawy
      @OmarElhatabawy Год назад

      you can use pin headers or jumper wires

  • @KnowYourselfIsOnlyWay
    @KnowYourselfIsOnlyWay 7 месяцев назад

    Use charger or adapter?

  • @carlosdiaz6671
    @carlosdiaz6671 Год назад +3

    Genial amigo, sencillo y directo, felicitaciones. Gracias por tu aporte.

    • @DixyPro1
      @DixyPro1  Год назад

      Muchas gracias, encantada de conocerte

  • @ionesidanut2068
    @ionesidanut2068 2 года назад

    Can I connect somehow the laptop charger to the back of the laptop on the battery connectors? Kids broke the charger port , not worth putting money into it . Just wondering how can I get a bit more of it

    • @DixyPro1
      @DixyPro1  2 года назад

      yes. The charger can be connected to the laptop directly, provided that the negative is with the negative. And the positive with the positive

    • @emmanuelvictor8762
      @emmanuelvictor8762 8 месяцев назад

      But is it safe that way

  • @anthony98
    @anthony98 2 года назад +1

    What did you use to make the connectors?

    • @DixyPro1
      @DixyPro1  2 года назад +3

      sheet of aluminum

    • @anthony98
      @anthony98 2 года назад +1

      @@DixyPro1 thanks

    • @anthony98
      @anthony98 2 года назад

      @@DixyPro1 another question, are the ones that go on a roof capable of making the contacts?

  • @kingoffreefire2345
    @kingoffreefire2345 2 года назад

    Kitna wat ka charger tha

  • @juliustupaz1799
    @juliustupaz1799 Год назад

    Well it work with any laptop battery?

  • @Dipeshdipacademy
    @Dipeshdipacademy 2 года назад

    What was the Battery volt and amh?

    • @DixyPro1
      @DixyPro1  2 года назад

      12 v _ 2 amp

    • @RadTeir
      @RadTeir 2 года назад

      @@DixyPro1 why 12v , 2a ?

  • @saharul2879
    @saharul2879 Год назад

    Bhai ye sabi bettery pe kam karge kiya

  • @anthonymickle4103
    @anthonymickle4103 2 года назад +2

    It's confusing bro...that meter didn't read negative although the leads were reversed...

    • @DixyPro1
      @DixyPro1  2 года назад +1

      If you reverse the polarity when reading the battery, the reading will be negative

    • @aaauto
      @aaauto Год назад +1

      I have two batteries at 0V and it's not showing polarity. I guess BMS shut off the circuit.

    • @tyrellwreleck4226
      @tyrellwreleck4226 Год назад

      There are no reading because because the pms is locked. If you open up the battery and put the terminals directly, it will give a reading

  • @leonbishop7404
    @leonbishop7404 Год назад

    what are those metal pieces? how do I get them? also, is it safe? doesnt proper battery charging require voltage regulator which is inside laptop I assume?

    • @DixyPro1
      @DixyPro1  Год назад +1

      This metal can be obtained easily, for example in tuna cans. Inside the battery there is a BMS circuit that is responsible for charging the battery, protecting it, and disconnecting the electrical current automatically.

  • @jimkovacs7
    @jimkovacs7 8 месяцев назад

    Beautiful, but that polarity reversal when you switch from the meter to the supply is confusing for many, bro !

    • @DixyPro1
      @DixyPro1  8 месяцев назад

      Yes, but it is not a problem. It is just a voltage measurement, the polarity setting does not matter

  • @blazeop88
    @blazeop88 Год назад +2

    Bro can I charge my laptop battery and the use it on my lap

    • @DixyPro1
      @DixyPro1  Год назад

      Yes, but this is not recommended

    • @NSAdin
      @NSAdin Год назад +1

      @@DixyPro1 then what should

  • @nexpro6985
    @nexpro6985 Месяц назад

    We don't know the polarity of the charger used. They are not all positive center. Also we don't know the voltage of that charger.

  • @deolaadebayo2632
    @deolaadebayo2632 Год назад

    Can I use 12v 1.5a

    • @DixyPro1
      @DixyPro1  Год назад

      Yes

    • @deolaadebayo2632
      @deolaadebayo2632 Год назад

      Thanks

    • @deolaadebayo2632
      @deolaadebayo2632 Год назад

      @@DixyPro1 do I have to use a connector. Can I just insert the wires directly from the charger?
      I can't for the life of me find a corresponding connector for the charger

    • @deolaadebayo2632
      @deolaadebayo2632 Год назад

      ​@@DixyPro1please can you answer this second question

    • @DixyPro1
      @DixyPro1  Год назад

      I use 12 v /2 amp

  • @scottlanier5133
    @scottlanier5133 2 года назад +1

    What voltage and amp was the charger?

    • @DixyPro1
      @DixyPro1  2 года назад +1

      12 volts . 2 amp

    • @muhammedsidhiq5389
      @muhammedsidhiq5389 Год назад +1

      Mobile charger is enough???
      9x2 volt

    • @mdumarinamdar
      @mdumarinamdar Год назад +2

      @@DixyPro1 you told in another comment that you have used 10 amp input

  • @rudijleis
    @rudijleis 2 года назад +1

    battery tested empty when positive lead was connected to negative terminsl,,,am i the only one??

    • @DixyPro1
      @DixyPro1  2 года назад +1

      Yes, you're right . But the battery is empty and that doesn't hurt anything

    • @danokode1194
      @danokode1194 2 года назад

      A multimeter reads in whichever way u put the terminals.

  • @Pyrid0xineOxide
    @Pyrid0xineOxide 11 месяцев назад

    Yiu think i could plug in a usb wall outlet plug into one?

  • @tecnomaxtm1738
    @tecnomaxtm1738 Год назад

    you didn't show how much volt to charge it, the battery could damage with the wrong volt.

  • @forwimplaysroblox8304
    @forwimplaysroblox8304 Год назад

    Can I use 13 amp

    • @DixyPro1
      @DixyPro1  Год назад

      No

    • @forwimplaysroblox8304
      @forwimplaysroblox8304 Год назад

      Long story short it blew up and it cut my solar panels for a sec and when I put it in my laptop is smoked and now my laptop shows no sign I'm done 😭

    • @UsuMan-uy5mu
      @UsuMan-uy5mu Год назад

      @@forwimplaysroblox8304 U r dead😂

  • @KGB_real
    @KGB_real 7 месяцев назад

    Bro its not working to my battery what should i do

    • @DixyPro1
      @DixyPro1  7 месяцев назад

      The internal battery contains 6 cells. If one cell is damaged and does not work, the entire battery will not work. Therefore, the cells inside must be examined

    • @KGB_real
      @KGB_real 7 месяцев назад

      @@DixyPro1 o thanks bro

  • @MrRmeadows
    @MrRmeadows Год назад

    I need to make something like this. Have a Dell Laptop that had issues. Would not boot OS. Was booting WinRE just fine. Battery would not charge in WinRE or when off. Now have 2 problems.

    • @gloryidigu1889
      @gloryidigu1889 7 месяцев назад

      These prob always happens to Dell!

    • @MrRmeadows
      @MrRmeadows 7 месяцев назад

      @@gloryidigu1889 Anyone fixing dells? I asked Luis if he would. He only works on Apple.

  • @subrahmanyam1
    @subrahmanyam1 Год назад

    how many miniutes to charge the battery, not told

  • @NSAdin
    @NSAdin Год назад

    Bro can i charge my HP laptop battery 🔋 like this ...?

    • @DixyPro1
      @DixyPro1  Год назад

      Yes, but do not use this battery with a laptop

    • @NSAdin
      @NSAdin Год назад

      I lost my laptop charger.. then what should I do to recharge the battery and use it

    • @alimajeed3570
      @alimajeed3570 Год назад

      ​@@DixyPro1
      Why?
      We trying to use it for the laptop

  • @markhonea2461
    @markhonea2461 Год назад

    The second to last shot the battery was not in the picture.
    Pretty sus. Can't believe it nope.

  • @squarehole4317
    @squarehole4317 2 года назад

    Does that mean I can discharge it WITHOUT a laptop???

    • @DixyPro1
      @DixyPro1  2 года назад +1

      Yes, of course

    • @squarehole4317
      @squarehole4317 2 года назад

      @@DixyPro1 will it require a modul or controller?

    • @DixyPro1
      @DixyPro1  2 года назад

      @@squarehole4317 No .The module is already in the battery

    • @squarehole4317
      @squarehole4317 2 года назад

      @@DixyPro1 if you have time will you show it to us? This could be something.

  • @MubalighTop
    @MubalighTop 2 года назад

    Hai, mas.. apakah saya bisa membeli chargernya. IC laptop saya rusak, jadi saya butuh charger eksternal dari laptop

    • @DixyPro1
      @DixyPro1  2 года назад

      Ya . Caranya sama seperti di video

  • @RixtronixLAB
    @RixtronixLAB 2 года назад +2

    Nice video, thanks for sharing :)

    • @DixyPro1
      @DixyPro1  2 года назад

      Thank you very much

  • @mize_yir_bizz
    @mize_yir_bizz Год назад

    I do this to charge a friends 20v Dewalt cordless drill using a dc power supply ..

  • @dhananjaykadam2786
    @dhananjaykadam2786 10 месяцев назад

    Thanks & regards.

    • @DixyPro1
      @DixyPro1  10 месяцев назад

      Thank you

  • @litsteve1968
    @litsteve1968 Год назад

    Wszystko pięknie i ładnie, pod warunkiem że wszystkie ogniwa są OK !

  • @sathishyogeshwaran8771
    @sathishyogeshwaran8771 2 года назад +2

    Super thinking and work 🤝👏👏

    • @DixyPro1
      @DixyPro1  2 года назад

      Thank you so much

  • @greengum_p
    @greengum_p Год назад

    Is it ok if i use 12v 5a for it? Im afraid my battery will blow up 😂😂

    • @DixyPro1
      @DixyPro1  Год назад +3

      The best is 12 volts 2 amps

  • @m.k.pathak2449
    @m.k.pathak2449 Год назад +1

    I neede it

  • @sunflowers6612
    @sunflowers6612 3 месяца назад

    👍👍

  • @maatiraouki9124
    @maatiraouki9124 Год назад

    C’est excellent merci beaucoup pour l’exercice

  • @iftikhar9090
    @iftikhar9090 Год назад

    cchargar vot and emper reply

  • @sampannarajraj
    @sampannarajraj 11 месяцев назад

    669 likes