Jet 3 How to Remove and Install a New Convertible Top on a Porsche Boxster S (Part 2)
HTML-код
- Опубликовано: 16 окт 2024
- This instructional video is Part 2 of 2, leading you through the details in installing a convertible top from a 986 Porsche Boxster (details will be very similar for a 996). Be sure to watch Part 1 for removal of the old convertible top.
Just finished installing the top on my '99 Boxster. THANK YOU THANK YOU!!!
So I’m going to order a new top from auto tops direct after watching this video as it looks straight forward enough, great details and clarity, wish me luck! Mark from the UK
I couldn't have gotten my top back on with out your help. Thank you
Happy to be a part of your success!!
Steven - Thanks for the great detailed videos! Just bought a Boxster that needs some TLC. I was able to replace the window regulator with ease watching your video. I took off the soft top last night and will embark on putting the replacement top on this week. I was skeptical of doing this myself until watching your video! Thanks again from a Texan living in Wisconsin!! Ciao
Amazing video..not many people go into so much detail with a job like this..I like the fact you repaired that plastic ridge piece and did it properly which all takes lots of time and effort..good job Steve.
Thank you, Steven, for creating this outstanding video. I replaced the top on my Boxster following this video, and I'm currently replacing the top on my son's Boxster. I don't think I could have done it without this video - the written instructions from the top supplier do not make much sense.
The step at about minute 5:00 in the video where the cord (with fabric sewn around a plastic cord) goes into the vertical metal slot is difficult, I struggled with this the first three times, then the fourth time went much easier using these steps: 1) The plastic cord sticks out at each end of the fabric, that cord on the leading edge tends to come out of the open areas of the slot, then jams. Push the plastic cord back until it's flush with the fabric on the leading side; let the extra cord hang out the back end. The fabric helps keep the plastic cord from slipping out of the groove. 2) The fabric is not stitched tight against the cord all the way to the end, this can cause the fabric to flare out in the open areas of the slot and also jam. Apply a little bit of superglue at the fabric end, clamp the fabric together and let it cure. This keeps the fabric tight against the cord while sliding into the slot. 3) Apply a little vaseline in the slot, especially each location where the open areas close back together, and on the fabric that slides into the slot. 4) Don't tug hard on the top fabric below the cord, that can tear the cord flap where it is sewn to the top. Instead, hold the top with your entire hand where the cord flap is sewn to spread the load when you tug on it. Don't tug hard in any case; if it's stuck, back up a little and try again. 5) Check that the entire length of the cord is straight while sliding it into the slot.
If you're thinking "oh no, don't use superglue or vaseline", those were both suggested by tech support at the top supplier and they helped tremendously with this step.
I hope this helps anyone else struggling with sliding the cord into the slot.
Lon, happy to hear this video provided the confidence for you to do this work! Thank you for the detailed supplemental guidance regarding the cord.
Hi mate, we used your video as a reference when fitting a top this week. Some of the tips were invaluable, appreciate the help and the effort you put in to making the video. Cheers Kev at Mega Trim in Dandenong, Melbourne Australia
Thank you for the kind words. Happy the video helped to minimize the unknown!
Awesome to hear! Makes me happy y’all are taking on this doable DIY
Very good explanation of the "little" details that make "big" differences. Thank you!
I am replacing my top at this moment. Your video was quite helpful
Thank you for your videos these are very detailed and very helpful for car guys who like to do their own stuff - by the way - GREAT GARAGE !! yes I like the others have a Porsche Boxster that is a great little car - after two 944's and two muscle cars - this one needs some love and you cant believe how much help you all have been !!!! Thank you so much !!
Good instructions no blasting music good job. I like this film. i worked 20 years for Porsche as mechanic, Service manager and District service manager. Taught automotive class and computer consulting to seniors at High School. I no a good instructor when I see one. I have three Boxster's one donor one complete and one I am building for racing at Bonneville race track..
We are elated so many of you have the confidence to do this work yourself! Thanks for the kind words.
-Steven
Great video. Very helpful. Just one note the elastic strap that you secure at the 3 min mark should have gone about 6" lower onto the plastic rivet on the inside of the pillar which holds the plastic slider in place.
Nah, he did it right. Even instructions that come with the top have a picture of it getting placed under that plastic rivet shown in the video.
Thanks for taking the time to make video really informative
Thanks for your help. This let me do my top.
Awesome video thanks for make boxster ownership so much easier .....
Thanks Steve. It has given me confidence to have a go. Cheers
Awesome Video! Thanks so much for posting. This was unbelievable help while replacing the top of my Boxster project.
Keep up the the nice work!!
Great instruction display for all of the general procedures, but the more difficult items were less than satisfactory from a visual point of view, which made their verbal explanation a little less understanding. At least for an old man like myself. When it comes to our learning senses, mine are more on the visual side. I’m sure that if I were to jump right in and tear things apart, things might become more evident, but on the other hand it would be nice to have a clearer picture of what I’m getting into before putting my vehicle out of service.
All the same, A+++
Thanks for the video...I'm in the middle of this job installing a Sierra top...I did notice you put the star washer on in the wrong order. It looks like you didn't have it touching the fabric? On mine it was screw, hook, washer, fabric. You had screw, washer, hook, fabric.
Good eye! can't say I recall this detail as it was many years ago. I haven't had any failures, so no worries on that front....for me. Those of you doing this job, please take note on the order when you disassemble.
@@roaringtigersgarage4672 It's a small detail, but the job does require a lot of detailed work. I've been watching and rewatching your series and Jason's garage ruclips.net/video/ML-rIbnx5ec/видео.html endlessly, while I finish my install (I'm almost finished). Best regards from Japan !
Nice video but one important part that is missing is how to secure the bottom of the top to the B pillar. There is a strip that should be secured under the plastic piece attached to the B pillar...at 4:40 in the video you can see it by your right hand. Did you just leave it hanging? I really think that the plastic pieces should be removed from the B pillar in order to fasten this correctly.
What is the name of the spray adhesive that you use?
Best videos on RUclips
thanks man.. makes and unruling job.. so awsome.. I feel like a pro now.. lol
Great video, I realize it’s been a while, but hoping you or some of your viewers could help. I got the new top on and it’s nice and tight and looks pretty good if I say so myself….but the window trim pieces where the cable tucks in behind…my cable will not go behind the time piece towards the rear unless I physically tuck it in and then it stays in place and looks great. It almost like the cable is too long, but I know that’s not the case. I can’t figure out what I’m not doing correctly. I’ve kept it closed for about a month thinking it would form into place. I hope what I’m describing makes sense, any help would be appreciated. Thanks to all in advance!
Randy, thanks for posting the comment/query. As you state, it has been a long time since I did this work, but I did not have any issues similar to what you describe. Honestly I can’t visualize your issue but perhaps one of the many followers (and Porsche DIYers) have insight!
am going to replace convetible top thanks for your video
I might actually attempt this! Great video. Any other tips since this video has been out for a few years?
In some cases people find that the new roof will not close completely. Some even learn to live with pushing it shut to latch. If this problem presents itself what would you suggest? 2003 986. Thank you
Any tips for a DIY fix when the rib holding the headliner in the channel right behind the top latch breaks? Mine just let go and is rattling. Looking on the forums, guys are saying the only replacement is a new top at $700+. Thanks.
You're Welcome, Paul. Thank you for viewing, and for the positive feedback!
Issue: After replacing top, when raising roof the B Pillar & Roof Frame don’t align correctly they are separated by 4mm instead of flush
Details:
1. 1999 Boxster
2. Replaced roof with Sunset AutoTopsDirect Acoustic Plastic Window Top
3. It seems like there is an obstruction as I cant apply force for it to align
Appreciate any guidance to fix this.
Sorry to hear you are having some challenges. Unfortunately has been many years since I did this work, and no longer have a Boxster available to try to understand the situation. Wishing for your “a-ha” moment!
Awesome videos!
What'd really be super nice is if you could add a listing of the materials you used in the video, is that something you would consider doing?
Thank you!
what year car did you change the top to a glass window? I know the 2003 started with the glass rear window, I also heard you have to change the mechanism to use a glass window, Can you put a glass window ( albeit a small window) on 2002 986?
Nice video.Is the 05 911 Carrera top similiar installation? And do all 911s have defroster receptacle,if it came with plasthuic window from factory?
The 996 generation 911 was developed at the same time as the 986 Boxster, and in fact share everything from the doors forward. I can’t say for sure but I would expect the process and mechanicals to be very close to the same for your 911 as described in this video
To the Roaring Tigers......how long did it take to remove and replace the convertible top on the Porsche Boxster?
Thought you posted links to the two sided tape and any other products you used. I guess I don't see them.
Does the glass window affect much your access to the engine compartment when the top is in service mode?
Could you fix the aluminium plates to the roof when on the floor
I've watched part 1 and most of 2 did he mention how long it takes ? Or did I miss it 🤔
I work slow and methodically. Plus you want the contact cement to fully cure. Plan on couple of days.
I'm also in Houston and would like to know where you would recommend to service my 2000 Boxster?
I'm doing the same brand top. Mine came with a cardboard header strip. Did you use that? Thanks for the video!
Fred,
Yes, that thin cardboard strip must be used along the front edge of the top. This step begins at 23:14 in video 2. Unfortunately I had technical video problems at this point, and didn't catch these details on video, although it is described. Follow the provided written instructions and you will be fine. Mask everything so you don't get spray glue on your interior fabrics.
Thanks for watching our videos. Good luck!
My top turned out great. Your video really helped!
Mine won't close all the way. Can't even get the latch to catch.. Do I throw a tarp on it and let stretch.. Or do I need to go back and try to reset the aluminum top plates to allow for more slack. Just could get the screws to line up... Any help is greatly appreciated.
Yes, too tight. the fabric is fairly robust and intended to be exposed to substantial heat and moisture, so its not gonna soften up and slack.
@@stevenbukoski4474 I undid the the cables and got it to force shut. So in your opinion, no way to hope it will stretch enough so I can reattach the cables?
How much does it take to replace the top ?
Still the how to way of replacing your top, different years have slightly different tops and have different benefits. there’s another guy changing his top with the red Boxster I watched his RUclips one, two and three also between the two of them there’s almost no questions on answered
What 3M adhesive spray are you using?
3M Super Trim Adhesive
Can’t believe you didn’t show the before/after photo of the new rear window!
Hi, i heard replacement tops never fall into place properly like the original and that i should change the plastic window only since it is pierced..anybody have input on this?
The replacement top we replaced in the Roaring Tigers Garage video works and "falls into place" exactly as it should.
Doing mine right now...youll have a second opinion from someone that is mostly clueless in a few hours ;)
Fit like a glove, took me about 8 hours but that was lots of breaks, a store run, etc... Only bit that was a pain was sliding in the roof to the side slots. Looks fantastic.
Thx a lot
Video TOP*****
Come chiudere la calotta manuale
Steve-you put a lot of effort into the video so why not before and after shot-you didn't show us the final result?
After consulting, 5 lesbian friends all agree: The Meeting and Week One is very common amongst the Gay Women World of Dating. Except (!) the "let's get married" part has been thought out, and it's not asked or agreed upon lightly. We Homos have much to learn from Lesbian Authenticity and their lack of relationship-killing FOMO.