Most likely you road In The Rain or after rain and water made its way up into the board of the rear tail light or through the Horn of the headlight. My rear tail light has burned up twice I've replaced it with an after-market one with no problems now
The evercross has a 10ah battery and clames 25miles on a charge,,,on level 1 I would say you would be lucky to see 18 miles. Also the claimed 800w motor is likley a 500w at 800w peak for it to run 28ridden. It has a 21a controller and would do better with a 25-30a, The pole is a bit weak and lower locking stym is also, but you can change the colors of the side lights with a hidden button. But the 2 units are simuler over all. The pro m4 with a 16ah 48v system gets a true 28 mile on a single charge, but that's at 10mph at 28-30 mph gps it will do about 17miles. The front shocks are loud as hell and rubber bushings are a must. The 500w motor has pushed me to 32mph GPS this took about a full block to reach that speed on flat ground and 175lb ridder. The side led lights flash no way around that, so I just disconnected mine,, I mean you could cut the flash relay out and run blue red or green lights by disconnecting the other wires,, but most can't do that,, There are more expensive models that are better but over all my studying the 2 even though the Evercross has a better front suspension the Kugoo pro m4 won me over, but this is just my opinion
My on button on the display is stuck so I'm thinking of ordering another display called tf500 or the z920. Do those also have these types of settings ?
@umersiddiqui2006 may not program to that controller, You're Lights may stay on May not work at all. Your speed on buter may not work. There's different things that can happen when you do not buy a compatible lcd display and controler together.
Hey I just bought a scooter, my one back at home does 45km from factory but my new one in Spain is limited to 25kmh. Iv upped the power to 100% but still stuck at the same speed. The only way it seems to go faster is by upping the magnets which is not recommend to do but that also messes with speed and only reads 12ish😂. Basically I need to get it set to do 45kmh but read 25kmh if police were to look at it. Thanks for any advice in advance!
Have you had any problems with trip counter and odometer being inaccurate? I checked mine with my phone and TF-100 counted almost 2 km more than GPS app did. Is there a solution to this?
Most of the time the speedometer can be off by a couple of miles per hr. That will cause the reading to be off, check your speed by gps if it says 25mph but the scooter says 28mph then adjust the wheel size to corect the speed, this will also change the distance of travel, Example of that may be the scooter says 10" on the wheel setting try to go to 9.8" play with the wheel size number until it give you the same reading as GPS.
Sadly NO, I disconnected mine. And ordered Amber color ones to replace the flashing ones....OK technically you can cut the flash relay out and directly wire it to run RED,GREEN, OR BLUE. Most won't know how to do that.
@@theebikeguy3852 what about the foot board lights nearest to the rear suspension mine keeps flashing without the light switch on as I power up as normal why ?
@@chrislangford5297 will it act normal other wise? There are 2 sets of lights on the left and 2 right side rear deck, it has blinkers and break lights built in, if all 4 are flashing I would say likley a bad horn,headlight blinker, unit is defective. If not explained futher.
I have the Pro version. But when I use the 48V settings than the battery shows half full but it’s empty. And when I use 54V I think the battery shows me the right status. Is that possible?
48 V battery starts its discharge at about 54Volts and goes down to about 41, and a 52v battery will show 58.8 full- if you are talking about the little battery on the lcd display with the 5 bars or so in it, this is not accurate always use the voltage meater to know the true voltage in the battery, not sure if this is what you ment if not you may need to clarify better.
P-12 should ne peddle.assest start Strength.... 1 through 3 or 1 through 5. Not sure how it will be on yours. The higher the number, the faster the take off will be when you start to peddle.
I have a kirin m4 pro, 48 v,in the settings on P 03 if i change to 24v or 36 v the battery level is 5 bars, if i change'it to 48 v it show's 2 bars?can u help me understand?u mentioned to charge at 41 w ?Its safer around 44 w ?
If you were dropping it to 24 or 36 volts if the controller and the LCD displayer program correctly it will send less voltage to the motor which will probably read a little bit higher voltage. But it's a 48 volt system and needs to be set at 48 volts. As far as the bars on the LCD display it's useless you need to go by the voltage indicator. As far as charging it you probably have a 2.5 volt charger you could go up to a 3.0 charger and not affect the battery. As far as the battery showing three bars I would make sure it has a full charge and test it with a volt meter see if it shows around 54.6. If it does you may have a faulty lid display. Most battery manufacturers recommend sizing the charger at about 25% of the battery capacity (ah = amp hour capacity). Thus, a 100 ah 48 volt battery pack would take about a 25 amp 48 volt charger (or less). Larger chargers may be used to decrease charge time, but may decrease battery life. Smaller chargers are fine for long term floating, e.g. a 2 or 4 amp "smart charger" can be used for battery maintenance between higher amp cycle use, but would be inefficient or burn up if used to bulk charge large capacity, deeply discharged batteries.
I no longer have the scooter I own a wolf Warrior now however the majority of them are just basically the same just type in Google or go to Facebook and put how to add bushings in front springs on electric bike electric scooter they're all basically the same
I've changed my monster magnets and my scooter goes faster. Had it since October and no problems with changing monster magnets. Set it to 20 or 15 and in 3rd gear hold on tight lol. I've went 45mph but it will drain the battery quicker of course 😆
Good job on that but .Your coil windings will also overheat easer and shorten thelife of the motor. This is my slow scooter my Outstorm runs 60mph. But we all make them our owne👍👍
@@theebikeguy3852 yes very true but I'm ordering me a mankeel with a max speed of 85km and 70-120 km range. But gonna take about 6 long weeks to get it ugh. China 😆
Po1 if it has it, for some reason some of them came with the p01 others start out at p02 like mine p01 would be your brightness otherwise you may have to purchase a new LCD display. Or try a hard reset just to see if that would fix it final thing and probably the easiest disconnect the high go connector from the controller to the LCD display close to The Handlebar make sure the arrows are lined up on the two plastic prongs snap it back together see if that won't bring it back
@@DBYRNE1984 no , it just resets everything to your factory setting your factory setting already has the correct magnets in the controller to tell the LCD display that. The only thing that you would have to change is if you use mile per hour you would have to switch it from kilometers per hour other than that nothing else should be done. But like I said I think I would go ahead and disconnect the LCD display at The Handlebar where the hydro connectors are first start there
My dashboard keeps making beeping sound and shuts off. I also noticed a USB slot on the back. How do I get the display to appear again after turning it back on. The battery is fully charged. The display is off and wont start. Any thoughts?
Never heard of the display making a beep sound that's weird. If your ignition switch works but the LCD display is not turning on then likely there is a wire between the ignition switch and the LCD display that the wire Has Come Undone broken or something to that effect. You can pull the controller out disconnect the throttle by tracing the wire giving it a couple of minutes plugging it back on to see if that will come back up if not it's possible it had a pinched wire. As far as the USB slot that is for mainly programming and used for auxiliary lights. It's not really set up for your cell phone if you try to put your cell phone in there sometimes it will kill the display or make the display go dark until you disconnect the phone.
Bro can you help me I have Kugoo M4 Pro I order it and i got it from a weak so i take the Scooter and start use it after the battery finish i try to charge it but only charging for 15 min and after the charge gave me green light and not charging what i should to do to fix it please help me
The battery should take 4-6 hrs to charge. Best thing to do is get a multimeter and check the volts on the battery and let me know what it says you can email me at Theebikeguy1022@gmail.com Or if you have face book join here there are a few mechanics on here as well as me. facebook.com/groups/615300659697280/?ref=share
It depends on if you live in the United States or if you're in the UK however though this is a good scooter you would probably be much happier with the Arwibon q30
I want to add another battery to the kugookirin m4. When I add another battery. So he doesn't work. That battery is 36v. Is it possible to combine a 48v battery with a 36v battery
Most Scooters or just that way. Depending on the controller LCD display excetera, possibly a different controller with a ey3 display would improve. And it is possible that the display on this finger throttle it might be a situation where the Hall sensor does not read the magnet on the throttle as quickly.
@@elicanbedelzadeh4227 No, it comes from the factory set. At a lower speed, all this does increase. The Sneed to let's talk potential with this specific battery and controller.
Because the LCD display has the components to handel 36v-72v in some cases so if the controller and battery are switch to 52v as long as the LCD conecters match the controller it will work in these setting.
Hi guys I have an evercross TF 100 scooter and I have a problem with it sum guy messed up my settings on my scooter and now the scooter will turn on but it won’t move if anyone k ies how to fix it please let me know🙏🙏🙏
@@ay_duos7336 You better hope he did not mess with the motor Pole magnets setting. If that was messed up it could Burn the controller up or the lc you display.
If I did a ride video ride I would have to use my phone and it jumps around to much. There are tones of Videos on you tube of that already...and I work 6 days a week, I just rest on Sundays, in the past iv done a few ride reviews but my Gopro was Stolen. And the about 6 months ago someone hacked my Facebook and you tube account, and deleted all my bigger reviews. I had to delet the accounts and start over so I lost about 8 ebike and escooter Reviews. I wish I had more time to do full reviews like I use to but that is why I do mostly over views of ebikes and escooters now. Very limited time.....but thank you for your responce.
it can't drive 65 km on an electric charge and drive only 13 km has a freeway speed of 53 km per hour without load and I don't want to shop at electric fustion. they do not comply with their warranty obligations
This is a ok scooter for the price there are better ones out the I own a couple of scooters one of them being a wolf warrior prothat will hit 80kmph with me on it . The Kugoo if I recall only has a 16ah battery not good for long rides my wolf a much better scooter has 28ah battery but I will likely go to a 34ah battery in the future. As far as warranty goes read and iScooter also known as icenwheel seam to do good as far as parts and warrenty.
On others you cannot. So that's somewhat disappointing because that leads to people that can sell these under false pretenses that's why others have a lockout after 100 miles
This video helped me a lot. Just bought myself one a few weeks ago, btw, hope you don't mind me asking, which is also off topic from your video, is it possible to use a fast charger on this unit or not? If so, what fast charger would you recommend?
I would not use anything higher then a 3a charger iv heard of people using a 5a but this can shorten the life of the battery and a fast charger can also flood the battery in some cases overheating the battery and could catch fire, it's always to use OEM charger and I belive they are 2.5a if I recall, if you find a 3a charger for the kugoo don't cheap out on a 25.00 charger get a well built charger $50.00 +
@@theebikeguy3852 I'm tempted to buy a fast charger seeing that this unit really charges pretty slow, but I'm also cautious whether or not this is a safe way moving forward for me; and in my researches I have never came across a topic that talks about this, so I'm really skeptical to a point to use a fast charger at this point.
@@MrSpeedyduck like I said a 3 amp charger is okay but never leave any electric vehicle plugged in unattended and do not charge overnight there is a slight risk but still a risk if the bmms fails while you were asleep this could cause a fire. Or if the charger fails, this almost never happens but there is still that possibility so it's always best to use caution
thank you super video
@@8bunker thanks for the reponce.
Gr8 explain bro👍👌
Yo 60k views let’s fuckin go you rock David. Thanks for fixing my Aventon Level today.
@@Tinman710 thank you!
Awesome video very helpful do you know about the foot board rear break light as mind keeps flashing with out the light on ?
Most likely you road In The Rain or after rain and water made its way up into the board of the rear tail light or through the Horn of the headlight. My rear tail light has burned up twice I've replaced it with an after-market one with no problems now
You should do the Kugoo M4 pro vs the Evercross H5 plz.
Or just say which one is better.
The evercross has a 10ah battery and clames 25miles on a charge,,,on level 1 I would say you would be lucky to see 18 miles. Also the claimed 800w motor is likley a 500w at 800w peak for it to run 28ridden. It has a 21a controller and would do better with a 25-30a, The pole is a bit weak and lower locking stym is also, but you can change the colors of the side lights with a hidden button. But the 2 units are simuler over all.
The pro m4 with a 16ah 48v system gets a true 28 mile on a single charge, but that's at 10mph at 28-30 mph gps it will do about 17miles. The front shocks are loud as hell and rubber bushings are a must. The 500w motor has pushed me to 32mph GPS this took about a full block to reach that speed on flat ground and 175lb ridder. The side led lights flash no way around that, so I just disconnected mine,, I mean you could cut the flash relay out and run blue red or green lights by disconnecting the other wires,, but most can't do that,, There are more expensive models that are better but over all my studying the 2 even though the Evercross has a better front suspension the Kugoo pro m4 won me over, but this is just my opinion
My on button on the display is stuck so I'm thinking of ordering another display called tf500 or the z920. Do those also have these types of settings ?
@umersiddiqui2006 may not program to that controller, You're Lights may stay on May not work at all. Your speed on buter may not work. There's different things that can happen when you do not buy a compatible lcd display and controler together.
What does the small display mean? Where it says 49.6 on yours?
Voltage, but the displY also has a voltage meter
@@theebikeguy3852 voltage from the battery? And what's the max amount of number that should be shown on it?
@@RAYY0925 54.6 is the max voltage for a 48v battery
Hey I just bought a scooter, my one back at home does 45km from factory but my new one in Spain is limited to 25kmh. Iv upped the power to 100% but still stuck at the same speed. The only way it seems to go faster is by upping the magnets which is not recommend to do but that also messes with speed and only reads 12ish😂. Basically I need to get it set to do 45kmh but read 25kmh if police were to look at it. Thanks for any advice in advance!
Would these be the same P Settings for the ienyrid m4 pro s+
If it's the same display yes, but sometimes company's will not use all p settings........Company a may use 1-17 but company B may only use 1-12
Have you had any problems with trip counter and odometer being inaccurate? I checked mine with my phone and TF-100 counted almost 2 km more than GPS app did.
Is there a solution to this?
Most of the time the speedometer can be off by a couple of miles per hr. That will cause the reading to be off, check your speed by gps if it says 25mph but the scooter says 28mph then adjust the wheel size to corect the speed, this will also change the distance of travel, Example of that may be the scooter says 10" on the wheel setting try to go to 9.8" play with the wheel size number until it give you the same reading as GPS.
Can you change the LED color?
Sadly NO, I disconnected mine. And ordered Amber color ones to replace the flashing ones....OK technically you can cut the flash relay out and directly wire it to run RED,GREEN, OR BLUE. Most won't know how to do that.
@@theebikeguy3852 what about the foot board lights nearest to the rear suspension mine keeps flashing without the light switch on as I power up as normal why ?
@@chrislangford5297 will it act normal other wise? There are 2 sets of lights on the left and 2 right side rear deck, it has blinkers and break lights built in, if all 4 are flashing I would say likley a bad horn,headlight blinker, unit is defective. If not explained futher.
I have the Pro version. But when I use the 48V settings than the battery shows half full but it’s empty.
And when I use 54V I think the battery shows me the right status. Is that possible?
48 V battery starts its discharge at about 54Volts and goes down to about 41, and a 52v battery will show 58.8 full- if you are talking about the little battery on the lcd display with the 5 bars or so in it, this is not accurate always use the voltage meater to know the true voltage in the battery, not sure if this is what you ment if not you may need to clarify better.
Hi I have a question this red nubers this 49.6 what is it this is temerature or the wats what is this ???
voltage of battery
Thank u for this but my scooter has a number 12 on the settings before 15 what is that for
P-12 should ne peddle.assest start Strength.... 1 through 3 or 1 through 5. Not sure how it will be on yours. The higher the number, the faster the take off will be when you start to peddle.
I have a kirin m4 pro, 48 v,in the settings on P 03 if i change to 24v or 36 v the battery level is 5 bars, if i change'it to 48 v it show's 2 bars?can u help me understand?u mentioned to charge at 41 w ?Its safer around 44 w ?
If you were dropping it to 24 or 36 volts if the controller and the LCD displayer program correctly it will send less voltage to the motor which will probably read a little bit higher voltage. But it's a 48 volt system and needs to be set at 48 volts. As far as the bars on the LCD display it's useless you need to go by the voltage indicator. As far as charging it you probably have a 2.5 volt charger you could go up to a 3.0 charger and not affect the battery. As far as the battery showing three bars I would make sure it has a full charge and test it with a volt meter see if it shows around 54.6. If it does you may have a faulty lid display. Most battery manufacturers recommend sizing the charger at about 25% of the battery capacity (ah = amp hour capacity). Thus, a 100 ah 48 volt battery pack would take about a 25 amp 48 volt charger (or less). Larger chargers may be used to decrease charge time, but may decrease battery life. Smaller chargers are fine for long term floating, e.g. a 2 or 4 amp "smart charger" can be used for battery maintenance between higher amp cycle use, but would be inefficient or burn up if used to bulk charge large capacity, deeply discharged batteries.
@@theebikeguy3852 thank you very much, new world for me.
hi! can u make a video about the springs, and show how u installed the rubber things there because I don’t really know how to do it please!
I no longer have the scooter I own a wolf Warrior now however the majority of them are just basically the same just type in Google or go to Facebook and put how to add bushings in front springs on electric bike electric scooter they're all basically the same
I've changed my monster magnets and my scooter goes faster. Had it since October and no problems with changing monster magnets. Set it to 20 or 15 and in 3rd gear hold on tight lol. I've went 45mph but it will drain the battery quicker of course 😆
Good job on that but .Your coil windings will also overheat easer and shorten thelife of the motor. This is my slow scooter my Outstorm runs 60mph. But we all make them our owne👍👍
@@theebikeguy3852 yes very true but I'm ordering me a mankeel with a max speed of 85km and 70-120 km range. But gonna take about 6 long weeks to get it ugh. China 😆
Is there a way to adjust the brightness levels. My has gone all but Invisible, however the start up logo is normal brightness.
Po1 if it has it, for some reason some of them came with the p01 others start out at p02 like mine p01 would be your brightness otherwise you may have to purchase a new LCD display. Or try a hard reset just to see if that would fix it final thing and probably the easiest disconnect the high go connector from the controller to the LCD display close to The Handlebar make sure the arrows are lined up on the two plastic prongs snap it back together see if that won't bring it back
@@theebikeguy3852 Fair play for replying. Does a hard reset change any of the magnet settings etc?
@@DBYRNE1984 no , it just resets everything to your factory setting your factory setting already has the correct magnets in the controller to tell the LCD display that. The only thing that you would have to change is if you use mile per hour you would have to switch it from kilometers per hour other than that nothing else should be done. But like I said I think I would go ahead and disconnect the LCD display at The Handlebar where the hydro connectors are first start there
@@theebikeguy3852 Will do. Thanks for your help. Be safe out there
My dashboard keeps making beeping sound and shuts off. I also noticed a USB slot on the back. How do I get the display to appear again after turning it back on. The battery is fully charged. The display is off and wont start. Any thoughts?
Never heard of the display making a beep sound that's weird. If your ignition switch works but the LCD display is not turning on then likely there is a wire between the ignition switch and the LCD display that the wire Has Come Undone broken or something to that effect. You can pull the controller out disconnect the throttle by tracing the wire giving it a couple of minutes plugging it back on to see if that will come back up if not it's possible it had a pinched wire. As far as the USB slot that is for mainly programming and used for auxiliary lights. It's not really set up for your cell phone if you try to put your cell phone in there sometimes it will kill the display or make the display go dark until you disconnect the phone.
Bro can you help me
I have Kugoo M4 Pro I order it and i got it from a weak so i take the Scooter and start use it after the battery finish i try to charge it but only charging for 15 min and after the charge gave me green light and not charging what i should to do to fix it please help me
The battery should take 4-6 hrs to charge. Best thing to do is get a multimeter and check the volts on the battery and let me know what it says you can email me at Theebikeguy1022@gmail.com
Or if you have face book join here there are a few mechanics on here as well as me. facebook.com/groups/615300659697280/?ref=share
@@theebikeguy3852 i will record one video for you and i will send it to you by email
How to return to on and off setting of my DD600 scooter throttle
Never heard of a DD600 and can't find anything about, what display do you have? Tf-100, EY3 or something else
Any idea how to delete E005 on my kugoo it won't drive please
where can i buy that scooter
It depends on if you live in the United States or if you're in the UK however though this is a good scooter you would probably be much happier with the Arwibon q30
ruclips.net/video/REs1suXsk0c/видео.html
Sir my M4 has P12 0-5 setting which is the fastest?
P12 needs to be lest alone p15 set to 100 for max speed
@@theebikeguy3852 p15 is 100%
What’s the horn called
@@zaidmati4643
www.amazon.com/Waterproof-Controller-Anti-Theft-Vibration-Rechargeable/dp/B09BZ5TH23?source=ps-sl-shoppingads-lpcontext&ref_=fplfs&psc=1&smid=A1VM8IW8D2PLKT
Comment on la déplie et plie s’il te plaît fais une video sur sa
@ZLK Az
ruclips.net/video/ajpVjHc6pvk/видео.html
I want to add another battery to the kugookirin m4. When I add another battery. So he doesn't work. That battery is 36v. Is it possible to combine a 48v battery with a 36v battery
NO NEVER, it will flood the 36v battery and cause a fire.
Batteries in parallel must be the same voltage, capacity, chemistry, and charge /discharge characteristics.
@@theebikeguy3852 ok thanks
@@theebikeguy3852 Thanks
i got Tf-100 with p-12. what is for p-12?
I believe p12 is pedal assist. So it's useless on an electric scooter it's pretty much nothing leave the settings as they are
How do i make acceleration kick off more faster than a 1 second delay
Most Scooters or just that way. Depending on the controller LCD display excetera, possibly a different controller with a ey3 display would improve. And it is possible that the display on this finger throttle it might be a situation where the Hall sensor does not read the magnet on the throttle as quickly.
How to change rpg light color
how to remove the battery signal in the display in electric scooter... TF - 100
You cannot remove the battery signal. That is what tells you. How much battery is left in the battery.
I have a kugo that doesn’t have p2 mine starts at p3 how do I change to miles
Sadly from what I have red some of the TF100 displays were not added because most countries use kmp , so it's luck of the draw.
If your in the UK it's the setting p1
thanks bro
I don't have the p2 option for some reason :(
For some reason a hand full of them don't have that option very weird
@@theebikeguy3852 only thing I can think of is region based speedos/ throttle
How to access to p8?
There is no setting p8 if you are looking for increasing your speed that would be p 15
Is it harmful to set p15 to 100@@theebikeguy3852
@@elicanbedelzadeh4227 No, it comes from the factory set.
At a lower speed, all this does increase. The Sneed to let's talk potential with this specific battery and controller.
I have a 48v16ah model but in the menu i van change it tk 52 and 60 why is that??
Because the LCD display has the components to handel 36v-72v in some cases so if the controller and battery are switch to 52v as long as the LCD conecters match the controller it will work in these setting.
@@theebikeguy3852 on the box its saya that my battery is 48v but in the settings I can change it so is it safe?
Hi guys I have an evercross TF 100 scooter and I have a problem with it sum guy messed up my settings on my scooter and now the scooter will turn on but it won’t move if anyone k ies how to fix it please let me know🙏🙏🙏
Factory reset the display
@@simcraftlol8475 how do I do that
@@ay_duos7336
ruclips.net/video/aUunL7J_i2Q/видео.htmlsi=jGrIUCzNHp8z9uCM
@@ay_duos7336 You better hope he did not mess with the motor Pole magnets setting. If that was messed up it could Burn the controller up or the lc you display.
Me i got also p12 but i don't know what for
Do pov video ride
If I did a ride video ride I would have to use my phone and it jumps around to much. There are tones of Videos on you tube of that already...and I work 6 days a week, I just rest on Sundays, in the past iv done a few ride reviews but my Gopro was Stolen. And the about 6 months ago someone hacked my Facebook and you tube account, and deleted all my bigger reviews. I had to delet the accounts and start over so I lost about 8 ebike and escooter Reviews. I wish I had more time to do full reviews like I use to but that is why I do mostly over views of ebikes and escooters now. Very limited time.....but thank you for your responce.
Vreau an traducere în limba română
@@CiuleiVasilesorry no idea what you said
it can't drive 65 km on an electric charge and drive only 13 km has a freeway speed of 53 km per hour without load and I don't want to shop at electric fustion. they do not comply with their warranty obligations
This is a ok scooter for the price there are better ones out the I own a couple of scooters one of them being a wolf warrior prothat will hit 80kmph with me on it . The Kugoo if I recall only has a 16ah battery not good for long rides my wolf a much better scooter has 28ah battery but I will likely go to a 34ah battery in the future. As far as warranty goes read and iScooter also known as icenwheel seam to do good as far as parts and warrenty.
The last mode d0 , u can reset when u want.. u dont need to have under 100miles on display... it will reset the miles/h even if u have 1000 on display
On others you cannot. So that's somewhat disappointing because that leads to people that can sell these under false pretenses that's why others have a lockout after 100 miles
This video helped me a lot. Just bought myself one a few weeks ago, btw, hope you don't mind me asking, which is also off topic from your video, is it possible to use a fast charger on this unit or not? If so, what fast charger would you recommend?
I would not use anything higher then a 3a charger iv heard of people using a 5a but this can shorten the life of the battery and a fast charger can also flood the battery in some cases overheating the battery and could catch fire, it's always to use OEM charger and I belive they are 2.5a if I recall, if you find a 3a charger for the kugoo don't cheap out on a 25.00 charger get a well built charger $50.00 +
@@theebikeguy3852 I'm tempted to buy a fast charger seeing that this unit really charges pretty slow, but I'm also cautious whether or not this is a safe way moving forward for me; and in my researches I have never came across a topic that talks about this, so I'm really skeptical to a point to use a fast charger at this point.
@@MrSpeedyduck like I said a 3 amp charger is okay but never leave any electric vehicle plugged in unattended and do not charge overnight there is a slight risk but still a risk if the bmms fails while you were asleep this could cause a fire. Or if the charger fails, this almost never happens but there is still that possibility so it's always best to use caution