Thank you! It is hard to call this one still an Ender as I went with few more upgrades to really test the capabilities, but the heart of it is there, that's true 😀.
@@vladimirbortnik2936 About the original Ender parts used it is very similarly to the v1.2 and it actually uses all the frame extrusions (v1.2 didn't use one). But the printer you see on the video has upgraded steppers and motherboard as I wanted to first build one that can go really fast so I can properly test the construction and the frame - with stock steppers I would first reach their limit and wouldn't see the real capabilities of the printer.
@@jnssmnsn It really is not perfect and as you can read in the description and in the video, I didn't do a complete calibration which would definitely help and I didn't bother tuning the print profile too much because that is not the priority at this time. If you mean the horizontal line on the hull, that is because it is printed in ABS and when you print the solid layers on the deck, it shrinks the print and creates that line. Maybe you mean even something else but as I said, it is really not perfect and not properly tuned. I was rather looking for artifacts from the printer construction (resonance, wobbly frame etc.) which are not really present so for me it is a good result/finding :).
Už přes rok stavím betu a furt se k tomu nemůžu dostat, abych to dokončil 😀 S takovou budou venku další 2 verze, než to dodělám 😀 Je to šílené, kam se tento projekt posouvá. Jen tak dál, máš můj velký obdiv
Celá tiskárna je v podstatě Voron z Lidlu... starý Ender a pár tyčí navíc s hromadou plastu. Ale co jsi z toho dokázal vytvořit, je vskutku dechberoucí 😉👍 Ať se daří a těším se, co nám ukážeš přístě 😎
Haha i tak by se to dalo říct 😃... Děkuju za pochvalu. Tahle nová verze už by ale možná do Lidlu nepasovala, je tam lineární vedení, žádné plastové spoje v rámu, takže i ta hromada je redukována, no a celé je to zase o kousek dál 🙂.
It will still take time until it is released, but if you are not in a hurry you might wait and compare and decide later when I will post some more details.
Right, it was too close to the bed but to my defense, there is no bed probe or Z endstop yet and I was playing with the lights at the start so I couldn't babystep it haha! It will be better in the future :). Thanks!
Very Impressive print! So clean! Your project is my next build with my spare ender 3's. Thanks aagin for the great design
Finally an Ender that can print fast and damn good 🥳
Amazing job buddy! 🤩
Thank you! It is hard to call this one still an Ender as I went with few more upgrades to really test the capabilities, but the heart of it is there, that's true 😀.
@RH3D_cz does it still have any original ender parts??
Is that really good though? The sides of the boat looks woblywarped, this is the number 1 artifact i hate the most when printing shit
@@vladimirbortnik2936 About the original Ender parts used it is very similarly to the v1.2 and it actually uses all the frame extrusions (v1.2 didn't use one). But the printer you see on the video has upgraded steppers and motherboard as I wanted to first build one that can go really fast so I can properly test the construction and the frame - with stock steppers I would first reach their limit and wouldn't see the real capabilities of the printer.
@@jnssmnsn It really is not perfect and as you can read in the description and in the video, I didn't do a complete calibration which would definitely help and I didn't bother tuning the print profile too much because that is not the priority at this time.
If you mean the horizontal line on the hull, that is because it is printed in ABS and when you print the solid layers on the deck, it shrinks the print and creates that line.
Maybe you mean even something else but as I said, it is really not perfect and not properly tuned.
I was rather looking for artifacts from the printer construction (resonance, wobbly frame etc.) which are not really present so for me it is a good result/finding :).
Už přes rok stavím betu a furt se k tomu nemůžu dostat, abych to dokončil 😀 S takovou budou venku další 2 verze, než to dodělám 😀 Je to šílené, kam se tento projekt posouvá. Jen tak dál, máš můj velký obdiv
Celá tiskárna je v podstatě Voron z Lidlu... starý Ender a pár tyčí navíc s hromadou plastu. Ale co jsi z toho dokázal vytvořit, je vskutku dechberoucí 😉👍 Ať se daří a těším se, co nám ukážeš přístě 😎
Haha i tak by se to dalo říct 😃... Děkuju za pochvalu. Tahle nová verze už by ale možná do Lidlu nepasovala, je tam lineární vedení, žádné plastové spoje v rámu, takže i ta hromada je redukována, no a celé je to zase o kousek dál 🙂.
@RH3D_cz Aurapol dělá zelený parkside filament 🤣 Lidl nabízí nářadí poměr nízká cena/dostačující výkon, takže to bylo myšleno v dobrém 🙂
Very satisfying. I cant wait to see what this is. Are you using PETG here?
Looks fun! very Voron of you
It is fun! Haha, yes the toolhead has Voron compatible mount as many people preferred.
Very nice!
Thank you!
From the title I thought that you were printing with filament made of **** :D
Haha :D This one was ABS fortunately
This is amazing! What nozzle size did you use?
Thank you! it is 0.5mm tungsten carbide nozzle.
I'm really interested in building one of these. But I don't want to print everything for V1.2 when V2 is right around the corner.
It will still take time until it is released, but if you are not in a hurry you might wait and compare and decide later when I will post some more details.
@RH3D_cz You see, I'll buy the parts, and it'll sit in a box for 11 months before I build it. By then V2 will be out haha
Is the intro song inspired by little green bag??? Sounds awesome.
it is "Stick The Landing - Bass (Stem)" by Everet Almond. But if he got inspired by the Little green bag I am not sure.
Let me know what I need to start buying 😂
I know you are ready 😂. Soon hopefully :)
Nice
Thank you!
1st layer too close to the bed but very clean print for 10min benchy
Right, it was too close to the bed but to my defense, there is no bed probe or Z endstop yet and I was playing with the lights at the start so I couldn't babystep it haha! It will be better in the future :). Thanks!
Kränk
v2 ?
@Nmorelm-e7e pump the brakes, bro lol
Yup. I am considering a different name but we both mean the same.
@RH3D_cz a new name might be a good idea to eliminate confusion