Peugeot 307 2005 curtain and side airbag open circuit P0091. Fault finding and repair.
HTML-код
- Опубликовано: 9 сен 2024
- Consider to support my channel and all the hard work put into it at / lmautorepairs
Thank you
How to do wire repairs:
• How do I repair damage...
Hi
This car came to me with the airbag light on.
Follow me on this video to see how I have diagnosed, fault find and repaired the problem.
Hope you enjoy the video.
Any question or comments, please put them below.
Like always, thank you for watching!
Thanks you so much for this, iv just copped a cheap 307 and hoping this will be the remedy, if it is I owe you a beer sir
☺️
🍻
👍👍👍
Thanks alot. I'm here because I have the same problem. Hope I'll nail it
I am sure you will...😉
Thank you for watching and for your comment!
Super good video!
THANK YOU, have a nice day sir
Hi
Thank you for watching and for your comment!
Huge thanks to you i had the same on my 307 and fixed it! It is a 2 door aswell.
Thanks!
For watching and for your comment!
Nice, I've had the same in a 2 door Peugeot where the seat constantly bends to let passengers in the back. Thanks Luis
One Auto,
Hi
Thanks Rob... This was actually a 2 door as well...
Thanks alot mate!!!! Ive had the same problem in a Citroen C4 Coupe and after i watched your video i have fixed the problem in 1 hour of work thank u thank u thank u greetings from Germany. :)
Hi
That's great news!
Thank you for watching and for the feedback!
I like the way you explain thank u a lot
Thanks!
For watching and for your comment!
hi mate just come across your channel great vid great channel
+bodgit and leggit garage
Better late than never.... lol
Thank you for stopping by...
Thanks a lot and very interesting.i think two yellow and orange wires are CAN wires .what is the role of other two wires
Nice fix.
☺️
Thanks!
👍👍👍
thanks sir for this nice video ,good explication.
Thank you for watching!
Nice work and a good find.
Thank you sir... Thank you for watching and for your comment!
Good job my friend. Cheers
ramon ruzic
Hi
Thank you Ramon...
Hola buenas yo tengo el Peugeot 206 y quiero buscar la falla así como lo has hecho. Mi pregunta es a qué cables conectó la resistencia? Al verde y amarillo ó al amarillo y naranja ? Me pudiera indicar? Saludos
good work bro
ecu repair
Thank you!
Good job. Tchanks You
👍👍👍
Thanks!
love your accent man, I have an 807 that since yesterday it yells the orange airbag light on and off, s I tend to agree a crap buit in low quality sold on overprice must be snapped of open. Now I have to find out how the hell you take off the front passanger seat in a 807 :) big up
😊
Never had one out on a 807...
I am sure you will figure out...
👍👍👍
Thank you for watching and for your comment!
Nice one. Very good video.👍
Automotive Solutions
Thank you for watching!
Hi friend, which cables and ports are for SEATBELT and CURTAIN AIRBAG in the cable/jack which goes from the floor to the seat... I want to install racing seats in my 307 and I need to bypass curtain airbag and seatbelt dashboard error...i want to install a 3.3 resistor in the jack which goes TO THE FLOOR...
thank you about that resistor idea. But that plug has 4 wires going to under the black floor/carpet and you put that resistor only in two holes/wires. Which one?
Hi
Or you follow the wires, to know which ones are which, or you need wiring diagrams...
Thank you for watching!
I have the same car and year. at 5:10 you've put resistor in to airbag source plug. It has 4 wires for two airbags. So why you didin't use two resistors (one for two wires airbag and then second for second two wires airbag)? But you've put one resistor into two holes only, and two wires left open without resistor. Why?
@@Radek__
I have done this long time ago... but, if I recall correctly, this was 2 wires for the side airbag, and two for the seat belt latch... 🤔
Sorry if I can't remember all the details now...
Hope that helps...
oh okay. don't worry. I will figure it out. I do not want to take Your free time anymore. Thank you for answer. Take care
How did rou open that plic ?!
Hi 2.2 nd 3.3 colur its similer 2.2 ohm 2red 2gold nd 3.3 ohm 2orange nd 2 gold
Hi I have the E691 code. Right side air bag and right air bag curtain in series fault. High stop. Any advice?
Yes... check wiring and connectors...
Thank you for watching!
👍👍👍
interesting video, you inserted a resistor of 3.3 ohms exactly. why it was not more than 3.3 ohms nor less than 3.3 ohms.
You can use sometimes higher or lower... depends on the systems... thank you for watching and for your comment!
Can you explain how to access to lateral airbag??I mean how to remove the back of the seat. Thanks in advance
I think you need to remove the while cover etc...
I done this some time ago... and can't really remember all the ins and outs... sorry.
Thank you for watching and for your comment!
Hi! Great and very useful video! I have this error code " C610 Front left satellite fault: Open circuit ". I already crimped the wires under driver's seat (replacing original connector) but the airbag warning light is still ON. I suppose the problem is the same as yours, but can I ask you how did you get access to the wiring for side airbag? I don't know how to dismantle the seat. Thanks in advance!
Seats are a bit tricky to dismantle, but can be done...
👍👍👍
Did you find where the satellite is as have c610 on my 407 thanks
@@barcrestbelenger2498 No, sorry (I sold my car a while ago).
Muito bom! TOP!
Obrigado!
👍👍👍
I know this is an old video but can anyone please help me find where I can buy the green connector piece. I’ve looked everywhere online
Hello, Really good video and I will try to do that by myself, understand need use 3.3 ohm resistor fine, but what about power of resistor: 0.125 or 0.25 or 0.6 [W]?? what which one to buy? Sorry if I ask stupid quastion but I'm not electronic expert... Please help. Best would be if you provide a link to website some shop with description this resistor. Thanks in advance.
greigna
Hi
Theoretically any one would do... but if you are going to buy it, just buy the 0.6...
The amount of current flowing through during the check is minimal...
Thank you for watching!
LM Auto Repairs g
Good job on the video. I'm troubleshooting a similar issue on my mum's 2006 Citroen C3. I have the same green connector under the seats but can't seem to figure out how to disconnect it. Any help would be appreciated.
FoxVictorBravo
Hi
There is a tab that you need to lift first...
I think...😉
Thank you for watching!
Thanks, I did lift the red tab which basically separates both connectors, but then there seems to be something more linking the 2. I'll give it another try tomorrow.
Hello, tks for the great content! Quick question, what were the positions you plugged the resistor into the connector to test it? Cheers
Position?
What do you mean?
Yep, position. I mean, Like connecting the resistor “legs” to the orange and yellow wire, green and white. Tsk and sorry for the beginner question 😉
Yes... you basically shunt the two wires...
👍👍
Hi my freind nice video like always.do you have lexia and pp2000 on the same pc or it should be installed on 2 different systemes?.thank you
Noureddine benguermit
Hi
Thank you for watching and for your comment!
They can be installed on the same pc, no problem.
OK THANK YOU SO MUCH
please sir if you can do a video about diesel injectors and how ecu control them .I want to understand how this system works thanks sir
+mohamed rahib
Hi
I could try... but surely there is videos here that will well explain all that in detail...
Great job
Im wondering if you have videos about radio systems passwords that how we can get them??
Yervant Khachadorian
Hi
I have and do that sort of stuff sometimes... but never recorded it...
I will think about it...
Thank you for watching and for your comment!
Thank you 😊
Greetings from Portugal. I have a similar problem on my wife's Citroen c2. The airbag light came out after she moved the drivers seat. My question is, what are the color Of The wires, to jump with the resistor? I couldn't see in the video, and I I'm afraid to do damage, by jumping the wrong wires... Big thanks and stay safe. 👍
Hi
Don't do that...
Don't bodge something that can save your life...
For testing purposes yes, but don't do it permanently!
Anyway, the colours might vary, depending on the car, year etc... so yours might be different colours...
Get hold of some diagrams...👍
Thank you for watching and for your comment!
@@LMAutoRepairs , thanks for the reply. I would like to try this, just for testing, to find if the fault is in the seat. I've been searching for a scan tool, that can retrieve Airbag codes, and they are quite expensive. I wouldn't disable the airbag. That would be gambling whith my wife's life... Once again, thank you, for the help. 👍
@@v8berenguer372
Give me more details about the car, and I will check for you...😉
@@v8berenguer372
Do you know the RPO by any chance?
@@v8berenguer372
No worries...
Driver side, the 4 pin plug, pin 1 yellow and pin 2 orange are the airbag circuit, the yellow with the green strip is earth...
Passenger side is the same, but colours yellow and orange are swapped...
All this colours on the car loom... not ot the seat side...
WHATEVER YOU DO, DO IT AT YOUR OWN RISK...
Hi there.
My seat belts were locked after some one gone into back of car. It was coming up with open circuit for seat belt tensioners both front and triggering of the pretensioners 6a0 i changed the belts but the only code remaning is triggering of the pretensioners 6a0.
What do you think do i need the module reset. The airbags never deployed. Its peugeot e7 2008 2.0 hdi thanks for any help
Hi
Without researching, I will say that most likely will need reset the "crash" data.
Although the airbags did not deployed, the pretensioners did, and you can't clear that.
Hope that helps.
Thank you for watching!
LM Auto Repairs thanks nice videos
بطل
Great video. Sorry to bother you. I'd like to make a question in case you can help: how do you know or find the resistance value for the airbag ? I have a Peugeot 308 with seat side airbags and everything is fine. I'm trying to install a 308cc seats and it is giving me error for the Airbag. I'm afraid if I can use a multimeter to test and measure between airbag wires or if that would deploy the seat airbag.
Erick Soares de Oliveira
Hi
You should be able to measure it without deploy the airbag, the amount of current sent by the multimeter is extremely low...
But, there is always a but, that is not advisable... do it at your own risk...
If you have a diagnostics tool, and it shows the resistance of the circuit, then you are sorted... otherwise is trial and error... but, it should be somewhere between 1.8 and 3 Ohm, I would say... I will check on my documentation to see if there is anything in there...
Thank you for watching!
lmsvvavr , thanks for your kindly attention. I'm afraid that my original 308 seat airbag is different from the 308cc , as the error happen only with the 308cc seats. Do you think that it would be safe to use resistors to adjust the proper value for the 308cc in my 308 system? I mean, maybe series or parallel to properly match the value if that is the case. Thanks
Erick Soares de Oliveira
I do understand that, and that is what I meant...
You can measure the resistance of the airbag of the original seat and then the replacement and work it out from there...
IT SHOULD NOT DEPLOY ANYTHING, BUT DO IT AT YOUR OWN RISK.
Try to research to see if you find any values... or try with the diagnostic tool...
lmsvvavr , thanks for your attention and reply. I will check that and try to find a diag tool to help me. Do you know or recommend to disconnect car battery, or 12v positive or ground when connecting and disconnecting the airbag connector? Regards
Advisable but not essential...
Can u explain how to use resister on plug under seat... it has 4 wires, how do I check which ones to connect too or do I use 2 resistors at the same time on?
TYRON MITCHELL
If you have 4 wires at the airbag plug, means you have a 2 stage airbag...
You need diagram to identify the pair that belongs to one of the stages.
Another way is to trace them from the airbag backwards.
You can also try and fail until you find the right ones... but I do not advice... unless you know what you are doing...
Hope that helps...
nice one, would you use the same resistor for all airbags? how did you know to use that exact value? thanks
+MrAsadEp
Hi
Well, experience is a factor in this case... but usually airbags generate a resistance around this value... when the tool shows you the resistance on live data, is a bit easier, as you can compare with a working aibag...
I understand,yellow color cable is for airbag,its right?,because my emulators having just two yellow cables,and from the video that I have see it now,there down the seat i have the seam green plug with the same 4 cables,yellow,orange,green and white color,just i need to know where in which place to attack emulator with two cables,,,
Armir shabanovski
In this case was the orange and the yellow...
But that doesn't necessarily means is the same on yours...
how do you find the correct value for the needed resistor ?
Hi
Most airbag systems work around those values...
Thank you for watching and for your comment!
@@LMAutoRepairs yes sir, but if you need the ohm spec where do YOU find it?
What service info and wiring diagrams are you using? do you know any tech/service -info sources on a lower $$ budget? Im working on a E61 525d 2005 with airbag and seatbelt warning lamps and also the yellow door in the cluster lcd screen, and the multimedia/ccc screen is blacked out...
no power on fuse 34 and 37... got any tips?
You are great!!!! THANK YOU FOR THE CHANNEL!!! Cheerz!
@@joachimjohan1215
For BMW just go online... BMW wds...
@@LMAutoRepairs i cant use it tried internett explorer, firdox and chrome..
@@joachimjohan1215
It is tricky due to the java....
Use old ie and java... should work...
As always great job lmsvvavr, I also have problem with airbags in my bmw e60. Seat belts and airbags light on. After diagnostic I found error "resistance firing circuit safety battery terminal too high". Can somebody help my to fix this problem?
Marius Juzeliūnas
Thank you for watching and for your comment!
Have you checked the terminal on the battery?
Make sure they are tight and corrosion free...
Hmm, battery terminal looks tight and clean. Few times I deleted error and lights goes out, but after week, sometimes after a month lights again on. But now I delete error and when I turn on ignition lights come on also.
Marius Juzeliūnas
Ok
You have at the battery terminal, positive side, an explosive device that fires in case of accident to disconnect the battery...
Check that connections to it are good...
So I need new positive cable? but if new cable will explode, what was the reason for the old cable to fail without an accident?
Marius Juzeliūnas
They are know to move with vibrations etc...
I am not saying that definitely that is your problem...
You need to investigate it further...
Google to understand what I am talking about...
Hi first of all thanks for this video. I hope i can explain my trouble. I have a question. My car is 307 2005 model 1.4 hdi. airbag light is on /off at different times for two months.
I broke the red part of green connector but i put it again and it is stable and constant. after that I used my car for 3 days. when i run the car after 3 days. the left (driver side) curtain airbag opened (exploded)
So, Is it my face or something else? and the green socket has 4 cable. are these cables +12V/ -12V or signal cable?
özgür çelik
With all the respect, if you do not know enough about airbags, do not touch!
If that curtain airbag deployed like that after you touch the plug, imagine if the steering airbag deploy while you are driving!....
Leave that for someone with some more knowledge!
I would say the first thing you should have done, before touch anything, was to scan the car...
Guessing on airbag systems is not a very good idea...
I don't want you to get hurt, so once again, my advice is to leave that and get it checked by a proper electrician....
thank you for your relpy. Absolutely i don't touch it. But I wonder that does this cause the socket to explode?
özgür çelik
Or something on that plug you have touched, or it might be that the original issue could be caused by some kind of short somewhere... an airbag only needs 12v and bang...
thanks lmsvvavr
özgür çelik
No worries...
nice repair bro, is it using 2.3 ohm or 3.3 ohm resistor?
Farhan Yaumal
Hi
You have obviously not watched the entire video lol... as I mentioned that... Anyway, for this test purpose I have used a 3.3...
i think i hear it 2.3 ohm, lol my bad
Farhan Yaumal
No worries...
nice channel btw, its so rare to find some fixing like these, especially for peugeot 307 and in english, subs!!
bom trablaho !
jean claude caetano
Hi
Thank you for watching and for your comment!
Between which wire I must connected the resistor?
Hisham Yousef
The two airbag lines/wires that run into the module...
Thank you for watching!
where did you connect the resistor which colors ?
+Wayne Azzopardi
Yellow and orange...
Can you fix my car? I have the same problem but I am not electronic. R u around London?
No, not near London...
Thank you for watching!
LM Auto Repairs do you have any electronic friend around me to advise?
@@xebbarkos
No in london... no...
hi , do you use a metal or carbon resistors
Ian Kelly
Hi
I believe these were carbon... but it was just to test anyway, as you have seen...
Hi,I would like to asked if you can help me,I have a peugeot 407 from 2005,and have a problem with the side left and right airbag and seat belt pretensioner...My car display show me Anomaly :Side airbag or seat belt with pretensioner and the airbag light is everytime on in my strument panel..I doit diagnostic by my self and with lexia diagbox and show me that:side right and left airbag high tension...!!! i have buy it allso two emulators but i dont know where to attacked this emulators,in which cable?Please if you can help me...Thank you
Armir shabanovski
Right, following an abnormal deployment of an airbag from someone that was asking me here for help, I will be quite straight on my reply...
If are not sure of what you are doing, don't do it! Especially when working on airbag systems...
I can advise you to find the correct diagrams for your car, and go from there...
Or, just leave that for someone that knows what is doing...
An abnormal deployment can hurt!
Thank you,but i think with emulator you cant damage nothing,now the problem i know where is,just need to find the right cable to attack emulator...
Armir shabanovski
Well, some cars including Peugeot, have airbags connected in series... so, you can accidentally deploy them...
Anyway, you need to trace down the circuit for the airbag you want to emulate...
The emulator connects to the two wires coming from the airbag module...
Hello lmsvvavr,
After the exchange and configuration of the BSI with your help, here in Brazil I managed to identify 2 problems that light the airbag, following another video of yours, I solved one that is the driver's bag, but the other do not know how to solve, maybe you Can you help me, the message is "side module trigger (right) open circuit" I have already seen that wire 6508 is in the green connector on the bottom of the passenger seat. But nothing connects in this thread, I do not have side airbags. Any tips? Thank you again!
Glad to hear that my videos were able to help!
Which airbags are fitted on the car?
i have a 307sw which has only the driver and passenger
Ok...
Have a look under configurations on the airbag module... with pp2000... see if all configuration is ok...
Look to see if there is any airbags enabled that should not be...
I also think it might be this, but the only options that are active are:
Pre tensioning seat belt
Driver's air bag
Passenger airbag
Desarming swihtch
Calibration of satelities: virgin ECU
And when I disable any of these appears a lot of errors
Magnus Moraes
OK...
Check the circuit from the module to the passenger side airbag...
Hi mate, I have a peugeot 206 gti and I had have the same problem... for all airbags is 3.3ohm?
Fernando Morales
Not necessarily... does live data shown the circuits resistance?
LM Auto Repairs I don't have live data :( you know it for 206 gti?
Fernando Morales
You need to try... it should be around that value anyway...
But have you scanned the car?
Which airbag is giving you a fault?
LM Auto Repairs i scanned and the problem is airbag of side... the gti have 2 airbag in the side, one of seat and one near the door
Fernando Morales
Be carefully, as they might be connected in series...
Hi, I bought a set of leather seats from a 2007 sport 307 and want to fit them in a 2001 lx Peugeot 307 but the connections at the bottom of the seats are different. Can I cut the wires and change the connectors over?
Thanks
Possibly...
Providing you connect everything correct...
👍
I wonder are the old seat airbags coded to the ecu?
Thanks
Should not be... As far as the "new" ones are within the same resistance range, should be ok...
Thanks for all your help I'll let you know how I get on, i will be fitting them in a week or so.
Have a happy Saint Patricks day, grettings from N Ireland !!
👍👍👍