this is a great setup, i was hoping you would know how i could use a speaker as output, also i wanted to play an audio file on the speaker if the vibration is exceeded. is this possible?
HI sir!! it was a great tutorial ever. A quick question, if we want to use the kit but with different platform like mobile phone, do we have to retype the programme again?
How can I boost the signal of the vibration sensor so the Arduino Board can see weaker signals coming from it? I know I'm missing some signals coming off the sensor using the set up in your video.
Hey, thanks for this video. It is possible to send a midi signal from the arduino, triggerd by the SW40? I want to trigger ResolumeVJ with vibrations for an university artproject.
Actually I am making a project on vibration sensor using arduino where we will be monitoring the vibrations of the machine and detect if it is vibrating above it's limited value.It would certainly be good if you gave a little advice .Is there a requirement of nodemcu if I need to display output on screen or that purpose is solved by the output window of Arduino IDE ?
Hello brother, I hope you're doing well after four years , i have a question and i hope that you have the answer for it . i want to read the values of the vibration i mean the real values in Hz so i can use it in my project and do some calculation . thank you and i appreciate your help
Hello. I wonder if you can help me. I'm trying to make a sound module that is activated by a shock sensor, but I haven't got much experience. I have bought a few voice modules and can't get them working and don't know where to connect the sensor.
Please help me solution I'm using a SW-420 vibration sensor whose output is analogous to a voltage unit. I really want to be able to convert the sensor voltage unit to Herzt (hz) unit. How to?
Great videos for beginner like me to study arduino. But i have a question, when i upload the code, there is a error code says "vibration was not declared in this scope" (On the first line of void loop). What can i do to solve the problem? Thanks
I want to create a rig that will allow me to measure the vibration of my boy's pinewood derby race car wheel and axles so I can determine which wheel axle combinations run the smoothest (least friction). Do you think this would be applicable. I'm not much of an electronics expert, but I can see how this could possibly work. Though I'd rather be able to read a numeric value for the vibration than just a led signal lamp.
you have different options, you can use this sensor, you can also use a piezo sensor, and you can also use mpu6050. But first you can try this one. its a low cost sensor, you should give it a try.
you can change measurement > 50 to measurement > 200 it depends on the sensitivity that you need so keep changing the number until it is too high for you then lower it slightly.
@@ElectroniClinic thank you so much. would you think it is possible to trigger a 7segment display using this vibration sensor, that it counts 0-99 everytime the sensor was trigger.
The you will have to invlove microprocessor as well. You will also make a computer application. Select something that you can make using only arduino and other circuits
sir i have a doubt since the sensor gives the digital o/p(0 and 1) so only 0 AND 1 only displayed in the serial monitor right.then how it displays values greater then 50
what is 50 in your code ...what is the unit ??? and what is the max value we can give ??..what is output unit of the vibration sensor?/??it=s it hertz or something else
it will make a delay for 50 millisecond between each time to apply the vibration(); meaning: the function vibration will feed arduino with vibration reads every 50 millisecond to display the events on serial
The only video about Arduino and related stuff which is to the point , informative and easy to comprehend .Keep up the nice work 👍
Thanks for the great tutorials. keep up the great work :)
this is a great setup, i was hoping you would know how i could use a speaker as output, also i wanted to play an audio file on the speaker if the vibration is exceeded. is this possible?
I have a separate video on how to play audio files. Check playlist.
can i use a 220 ohm resistor instead of 330? plz answer
what is the unit of the output values we are getting? ? I mean I want my vibration sensor to give the values in hz. Is it possible?
HI sir!! it was a great tutorial ever. A quick question, if we want to use the kit but with different platform like mobile phone, do we have to retype the programme again?
GOOD job
How can I boost the signal of the vibration sensor so the Arduino Board can see weaker signals coming from it? I know I'm missing some signals coming off the sensor using the set up in your video.
Instead of powering a LED, can I get it power something that draws power from a USB cable?
Thanks for this video. Can I have more details about Vibration Measurement Unit by this sensor.
Did you found the answer?
Hey, thanks for this video.
It is possible to send a midi signal from the arduino, triggerd by the SW40? I want to trigger ResolumeVJ with vibrations for an university artproject.
Actually I am making a project on vibration sensor using arduino where we will be monitoring the vibrations of the machine and detect if it is vibrating above it's limited value.It would certainly be good if you gave a little advice .Is there a requirement of nodemcu if I need to display output on screen or that purpose is solved by the output window of Arduino IDE ?
Did you got the output.plzz say iam also working on that project
Hello brother,
I hope you're doing well after four years , i have a question and i hope that you have the answer for it .
i want to read the values of the vibration i mean the real values in Hz so i can use it in my project and do some calculation .
thank you and i appreciate your help
can we use this to convert vibration into electricity?
Use piezoelectric sensors.
can I use stepper motor instead of led. please reply to me
yes you can use if you know how to use a stepper motor. check playlists i have videos on stepper motors.
@@ElectroniClinic Thank you so much
Hi, what if I want to use it as an alarm and only turn on the sensor when the alarm is on so it won't interfere with another loop.
Hello. I wonder if you can help me. I'm trying to make a sound module that is activated by a shock sensor, but I haven't got much experience. I have bought a few voice modules and can't get them working and don't know where to connect the sensor.
Please help me solution
I'm using a SW-420 vibration sensor whose output is analogous to a voltage unit. I really want to be able to convert the sensor voltage unit to Herzt (hz) unit. How to?
what is the units of readings??
Did you found the answer please?
Hertz is guess
can vibration sensor detect the frequency of faulty component such as resistor or capacitor?
no.
it is only used to monitor the physical vibration.
@@ElectroniClinic ouh okay thank you
I have sw 420 with 4 pins what to do with a0 pin in the sensor
what is the umits for vibrations displaying on the screen???
Did you foud the answer?
Did you figure it out...?It is hertz or something?if u know plzz tell me
Can we interface load cell and vibration sensor inthat how the code should be???
If i want to measure the vibration of dc motor, is this suitable sensor to use
It is a useful video for me.... I would like to know about the unit of vibration.... is it in Hz??? Or any other unit.... kindly replay....
Hz is unit of frequency. Unit of vibration is mm/sec.
@@ibrahimhcaglayan So the reading shows in serial monitor is mm/s ???? @
Great videos for beginner like me to study arduino. But i have a question, when i upload the code, there is a error code says "vibration was not declared in this scope" (On the first line of void loop). What can i do to solve the problem? Thanks
Were you able to solve it??? I have same problem
Can this thing wake an Esp8266 from deep sleep if a vibration is detected?
What is the unit of those values in the serial window ??
Where can you download the Arduino software? I want to download but I don't know where I can find it.
I want to create a rig that will allow me to measure the vibration of my boy's pinewood derby race car wheel and axles so I can determine which wheel axle combinations run the smoothest (least friction). Do you think this would be applicable. I'm not much of an electronics expert, but I can see how this could possibly work. Though I'd rather be able to read a numeric value for the vibration than just a led signal lamp.
you have different options, you can use this sensor, you can also use a piezo sensor, and you can also use mpu6050.
But first you can try this one. its a low cost sensor, you should give it a try.
coz the way i used it, you can now decide, its gonna work for you or not.
Does it trigger if you are holding the breadboard in the air?
yes
Can we adjust the sensitivity of the sensor so that it can sense only high vibrations?
That can be adjusted by potentiometer on the sensor.
you can change measurement > 50 to measurement > 200
it depends on the sensitivity that you need so keep changing the number until it is too high for you then lower it slightly.
Hi, what is the purpose of the resistor? Do you have the circuit diagram for this project?
It's available on electroniclinic.com
would there be an application for sensing seat (Such as a car) vibrations specifically measuring vibrations as a frequency.
I'm also looking in to that. Did You find out how to connect this with some software showing vibration graph in real time?
@@nartymmd Have you find out something because I currently need it?
@@florianbourchenin1206 Yes, ADXL345 accelerometer :)
@@nartymmd Can you share me your code ? :)
Thanks!
can you make these into wireless communication using nrf24l01?
Yes. I have many videos on nrf24lo1
@@ElectroniClinic thank you so much. would you think it is possible to trigger a 7segment display using this vibration sensor, that it counts 0-99 everytime the sensor was trigger.
Ya it can be done. Once you detect the vibration then you can do anything.
Check my other videos on vibration sensor.
ive alreary try. but the result is not ok. do data is being accepted with the use of nrf24l01
Can you help me to write a program for stepper motor control using vibration sensor
watch my videos on stepper motors. All you need to do is copy that code and paste it into the if condition block.
can u help me, i need the code for two or more vibration sensor like that SW-420 ,
What is practical application of this set up
Cam you make a video for vibration measurement using adxl345 accelerometer sensor
In which language this code was written
can you give me an idea for my final year project? using arduino
Yes sure. Tell me ur field of interest ??
Robotics ?
Communication ?
Power ?
Security ??
Electronic Clinic just only have audio and video .
sorry didn't get you. tell me in detail ? audio and video what ?
@@ElectroniClinic the project must have audio and video such as sounds and light for example.
The you will have to invlove microprocessor as well. You will also make a computer application.
Select something that you can make using only arduino and other circuits
Can we use the ADXL345 accelerometer? If yes then how to convert acceleration to Vibrations?
i like your voice
Thanks!!!
What name arduino?
sir i have a doubt
since the sensor gives the digital o/p(0 and 1) so only 0 AND 1 only displayed in the serial monitor right.then how it displays values greater then 50
it is the duration of pulseIn function
Thanks bro...
Whats the unit
what is 50 in your code ...what is the unit ??? and what is the max value we can give ??..what is output unit of the vibration sensor?/??it=s it hertz or something else
I would also like to know.
i'd also like to know...
it will make a delay for 50 millisecond between each time to apply the vibration();
meaning: the function vibration will feed arduino with vibration reads every 50 millisecond to display the events on serial
Can you please share the code
I really freaking need someone to use a vibration sensor that measures intensity and not freaking on and off
any luck? bc same
Bro loop is not verified
No measurements shown
What is the unit of this mesurement
Did you found the answer please?
@@dichoukarima2454 From the datasheet it is Microsecond
Code pls
@@gokulpriya-y4u it's available on electroniclinic.com
can u send the code?
its available on my website electroniclinic.com
سلام هل يمكنكم عمل لايك واشكرك