you cant, its a hardware limitation, since it only has 3 driver ports, and the 2y outputs are both connected to the same driver, so gantry squaring wont work either
what laser module dlc support ? PWM or TTL laser need be and what volt need be, 12 or 24 volt laser module ? i have dlc32 board and 24V power supply and need buy laser module next. but not know what makerbase support drive. PWM or TTL and 12V or 24V.
I set this card up with three external stepper drivers for my homemade 3 axis CNC machine. I'm using open builds control to test everything and it seems to be all working correctly. I'm wondering if I need to supply the board with 5 volts if it's not connected to USB? Or does it get all of its power from the 12-volt connector?
I am having a problem like once I connect my msk laser tool for wifi and after that If I disconnect the power then my board is not connecting again I'll have to connect the board and reconnect for software while plugging so there is any to skip this ?
Do you put driver boards on main board? They are sale separately in some offers.If yes check is they right connected to the main board. If yes you need data sheet for Nema motors to see what pin for what is. Good luck 🤞
it is probably the forces of the endmill pulling down on the z axis, and the stepper isnt strong enough to hold it in place. mayby try a straight flute or downcut endmill, the dont produce that much force pulling down
@@abhayvk8310my understanding is that makerbase used to offer z-axis control in their app but they removed it. I think if you sell a card that is supposed to control x y and z axis then you should have an app that can control x y and z axis.
Which version of firmware you installed, the latest 2.30 was disable that Wifi autoconnect feature temporarily, to fix some bugs…if you want it back, best to flash the older version, 2.10 or 2.08
But here there are two "Y's" and not XYZA . How do I solve on the software? Thank you very much.
you cant, its a hardware limitation, since it only has 3 driver ports, and the 2y outputs are both connected to the same driver, so gantry squaring wont work either
nor will there be enough power on the yy
Can you share the stl file for the case?
what laser module dlc support ? PWM or TTL laser need be and what volt need be, 12 or 24 volt laser module ? i have dlc32 board and 24V power supply and need buy laser module next. but not know what makerbase support drive. PWM or TTL and 12V or 24V.
Very nice explanation 👍😇
I can use this board with the draw cnc ?
I set this card up with three external stepper drivers for my homemade 3 axis CNC machine. I'm using open builds control to test everything and it seems to be all working correctly. I'm wondering if I need to supply the board with 5 volts if it's not connected to USB? Or does it get all of its power from the 12-volt connector?
need use 12-24volt power supply and connect to power plug.
how do you set a zero point to start from
can this board use for 10 watt optical power for laser diode? thanks
I am having a problem like once I connect my msk laser tool for wifi and after that If I disconnect the power then my board is not connecting again I'll have to connect the board and reconnect for software while plugging so there is any to skip this ?
Maybe you can try to reflash the firmware back to 2.10 or 2.08 as shown in the video
What is "S" axis? I noticed mine jumped to 50 today. Weird.
does lightburn work with this??
The TwoTrees Laser I have uses the same board less the display board. I have no problem using the latest version of LightBurn.
lightburn or lasergrpl can use.
please can you tell me about the wiring of the nema17 with mks dlc 32v2.1. I am facing issue with the running of the motors with the board.
Do you put driver boards on main board? They are sale separately in some offers.If yes check is they right connected to the main board. If yes you need data sheet for Nema motors to see what pin for what is.
Good luck 🤞
@@sash-v7i would a cnc shield work with this board to drive the nema 17 steppers
@@glennmartonic6376 this board have all ,not need external cnc shield board. this is all in board.
would this work for the 2D Pen Plotter with all the same feature or is it just for laser engravers
Think yes if you're machine work with G-code commands.
How are you buying it in India?! Or is there any Indian supplier?
Can we add relay for automatic spindle switch?
Можно ли подключить к этой плате старый offline contriller с кнопками?
Hi sir can you please give case stl files. Dlc32 board case.
stl files have lot at thinkiserve or other sites.
if wifi setting installed are can still use in Lightburn?
Yes,go to Lightburn in settings and re-add laser again with wi-fi connection.
Name of application name not available on play store in india
MKS Laser
I am having an issue using this board. During the milling, the Z axis is going down. Do you know what happening?
it is probably the forces of the endmill pulling down on the z axis, and the stepper isnt strong enough to hold it in place. mayby try a straight flute or downcut endmill, the dont produce that much force pulling down
Change Your stepper motor ,I got the same issues last month
@@DearChina1 The issue was solved? Did you use some special stepper motor?
@@flopesffno just replace with the same,yes isssues was solved
Why doesn't the mobile app have z-axis?
Because the app is for laser, and laser do not use z axis
@@abhayvk8310and yet he says it's for any CNC machine that needs x y and z axis control.
@@abhayvk8310my understanding is that makerbase used to offer z-axis control in their app but they removed it. I think if you sell a card that is supposed to control x y and z axis then you should have an app that can control x y and z axis.
my dlc32 v2.1 board does not auto connect to wifi
L
Mine does😂😂
Which version of firmware you installed, the latest 2.30 was disable that Wifi autoconnect feature temporarily, to fix some bugs…if you want it back, best to flash the older version, 2.10 or 2.08
Does it support Lightburn?
The TwoTrees Laser I have uses the same board less the display board. I have no problem using the latest version of LightBurn.
Where to bay this full kit in chip price😊
Aliexpress, usa, Both the control board and the display board for less than $20.00 USD.
@@jwrtigerboth for 19, cant find that.. You mean together about 40 $?
You realise there is almost NO support for this board and the last firmware update was a year ago?
Which board do you suggest to buy?
up
If possible to use for CNC router
Yes
It’s labeled as a cnc laser machine you just connenet a spindal to the port that says spindal
thanks
for what?
thank you for sharing, can you share the file for the case
documentation is weak also
Goyette Hills
🤔
loses steps regularly
How may i contact u