Configuring Danfoss VLT Micro FC51 for Process closed loop system using 2-wire Pressure transmitter
HTML-код
- Опубликовано: 12 сен 2024
- Two wire start stop with process closed loop system using two wire pressure transmitter for Danfoss VLT Micro FC51 Drive || Digicon Automation
Parameters :-
1-00 Configuration Mode [ 3 ] Process
1-01 Motor Control Principle [ 0 ] u/f
1-20 Motor Power As per motor name plate
1-22 Motor Voltage As per motor name plate
1-23 Motor Frequency As per motor name plate
1-24 Motor Current As per motor name plate
1-25 Motor Nominal Speed As per motor name plate
3-03 Max. Reference (Set-Point) 3.5 Bar
3-10 Preset Reference 100
3-15 Reference Resource 1 [ 0 ] No function
3-16 Reference Resource 2 [ 0 ] No function
3-17 Reference Resource 3 [ 0 ] No function
3-41 Ramp 1 Up Time 25 sec
3-42 Ramp 1 Down Time 40 sec
4-10 Motor Speed Direction [ 0 ] Clockwise
4-14 Motor Speed High Limit 50Hz
4-16 Torque Limit Motor Mode 250%
4-17 Torque Limit Generator Mode 250%
5-10 Terminal 18 Digital Input [ 8 ] Start
5-11 Terminal 19 Digital Input [ 0 ] No function
5-12 Terminal 27 Digital Input [ 0 ] No function
5-13 Terminal 29 Digital Input [ 0 ] No function
5-15 Terminal 33 Digital Input [ 0 ] No function
6-22 Terminal 60 Low Current 4.00 mA
6-23 Terminal 60 High Current 20.00 mA
6-24 Terminal 60 Low Ref. / Feedback Value 0.0 Bar
6-25 Terminal 60 High Ref. / Feedback Value 10.0 Bar
7-20 Process CL Feedback 1 Resource [ 2 ] Analog Input 60
7-33 Process Pi Proportional Gain 2
7-34 Process Pi Integral Time 7
Thank you, from Algeria !
Very useful video sir 🎉😊😊 please make a video on danfoss 301 drive
I have done and it is working good. The only point I want to understand when VFD counts 0.0 HZ (Reaching set point) a frequency sound coming from the motor. Is it normal or anything to do? And also please suggest is it safe operating VFD where the line voltage is 445 V ?
❤❤❤❤good video🎥🎥
Buen día. Será que me podrías apoyar con los parámetros y conexión que debería utilizar para un alternado de dos variadores con transductor? Es decir que encienda uno, se para y encienda el segundo, luego se pare y encienda nuevamente el primero etc
🙏🏻
Nice
Good day. Could it be that you could help me with the parameters and connection that I should use for an alternating of two inverters with transducer? That is to say, light one, stop and light the second,
jo parameter ap set karty hain wo manual sy show karwaya karo tu ziyada samaj ay gi.
How you changed the unit to bar sir?
Dear Digicon automation, If I want to run the vfd at 50hz when the mA feedback will be 20mA, 25hz when the feedback will be 8mA and 0hz when the feedback will be 4mA, then what setting i need to do?
Sir konse Perameter se Perameter with details aata hai
Can I apply to VLT Aquos Drive this setting?
Sir good
How to connect 1024 por encoder & programming in FC-051 danfoss drive
Sir fc 51. Vfd.2 wire selector switch on command given. Running ok. In case power failure. Again come power. Vfd on directly. When ever power come selector switch reset on. Pls perameter number tell me sir
2 wire vfd start command given sir. With selector switch.. But inase power failure. Again come. Selector switch on Position automatically on. But i want power come vfd selector switch rest on/off. Perameter number tell me sir.
Bro pls guide as how wiring pulse output using sensor (NO)
sir muje main motor ke Amp pr automatically speed low & high kese kr sakte h ....pls
Aap is channel par aur bhi video dekho usse aapko jyada idea aayega ..
Sir kindly reply please bcz i need your help in hvac project.we used danfoss fc051 drive. Sir mera velocity sensor hai wo 0-10v ka he sensor ka output jo vfd ke liye input huwa. Switch s200 off rakh ni hai vfd me 0-10V ke liye. Help ye Chahiye ke vfd ka output 42 port 0-20 ma he. To us ko 0-10v me kese set kare? Sir can you share your number?
dear sir, connect 500 ohm resistor parallelly between terminal no. 42 and ground terminal 20..
@@DIGICONAUTOMATION Thank you sir
@@DIGICONAUTOMATION sir can i get your email id bcz i need one more help about modbus parameters read configuration?
Parameters lock and unlock kaise karte hai
what is the setpoint parameter? thanks
3-03 Max.reference (set-point)
Another way to have setpoint is set par. 3-03 as high limit of pressure sensor and par. 3-10.0 as % of that limit. So if you have pressure sensor 0-6 bar and you need 2,5 bar just set 2,5/6*100=41,67% into par. 3-10.0. To check the proper value of reference see par. 16-01 (bar) and feedback par. 16-52 (bar).
@@DriveIgorhow to change standby time?
@@DriveIgor Dear tech-energy, If I want to run the vfd at 50hz when the mA feedback will be 20mA, 25hz when the feedback will be 8mA and 0hz when the feedback will be 4mA, then what setting i need to do?
@@joysharma3282 Hi Joy! You have to set par. 7-30 Process PI Control: [1] Inverse
Setup-2
Parameters
I m facing a problem in this type of configuration
I m working on fc102
P.t range is -1 to 34 bar and i need to start the motor at 15 bar and accelerate to maximum on 17 bar
Would you please like to send me the settings parameter for this situation
I will be realy very thankful to you
S/N950202A252
Setig