Replace Oven Bulb “how to Guide” Bosch Oven & many more💡Diy
HTML-код
- Опубликовано: 8 сен 2024
- This video shows how to replace a blown oven bulb.
This oven is a Bosch, but many others are exactly the same. The bulb that I am fitting is a Philips SES 25 W E14 Oven bulb which was bought from Screwfix in a pack of two for £2.19
Genuine Plastic Tool for removing bulb cover £7 on amazon amzn.to/2TMUnry
Amazon Link to oven bulb, amzn.to/371lLq5
Link to big Grips, amzn.to/2M6SHoz
Thanks for the great tip - could not budge the glass cover using the special tool - complete waste of time and money - followed your blog and Bingo - again many thanks
Thanks for the great comments👍🏻👍🏻🛠
Thanks mate, have been scratching my head over this for ages. Great tip!
Thanks for the great comments👍🏻👍🏻🛠
For anyone attempting this, you dont need pliers or a special tool to remove the glass cover. Just a tea towel or gloves to protect your hands. It just unscrews anti clockwise, if anything pliers run the risk of damaging the glass cover. The cover is basically a small jar, unless it baked on you'll be fine with your hands.
Thanks for the great information👍🏻👍🏻🛠
Yeap, worked for me as well, The 14 W is not very bright. I have accidentally bought the 14 W. The Bosh manual, at least for my oven recommends 40W.
Great tip about the pliers. I tried exactly what you did and presto, it loosened easily.
Glad it helped, Thanks for the great comments👍🏻👍🏻🛠
This worked for me thanks, tape on a pliers wrench. belling oven. I also saw a tip to warm the oven up before loosening.
Great tip! Thanks for the great comments👍🏻👍🏻🛠
Thank you for demonstrating how to replace Oven bulb.
You are welcome! Thanks for the great comments👍🏻👍🏻🛠
Thanks for the help, I unscrewed the light dome without any problem, used my hand
Glad it helped, Thanks for the great comments👍🏻👍🏻🛠
thanks for this tutorial! I got the same oven model and I have opened bulb cover by hand it just alittle bit tight
Glad it helped! Thanks for the great comments👍🏻👍🏻🛠
Thanks for the video. Just replaced my bulb quickly and easily. Thanks again.
Glad it helped Thanks for the great comments👍🏻👍🏻🛠
This worked a treat for me and I am the least diy person. Thank you.
Glad it helped Thanks for the great comments👍🏻👍🏻🛠
Worked a treat! I didn't have any electrical tape, so I used masking tape, worked just as well. Thank you for the top tip!
Glad it helped! Thanks for the great comments👍🏻👍🏻🛠
Yes! Thank you so much! I tried removing the glass cover and got to the "twisty twisty nothing happening" moment... so tip on using pliers :)
Glad I could help! Thanks for the great comments👍🏻👍🏻🛠
THANK YOU big time. would never though to use pliers on glass but it worked
Glad I could help Thanks for the great comments👍🏻👍🏻🛠
Fantastic video finally i solved my problem and unscrew the bulb that was really sticky. Greetings from Portugal Thank you
Thanks for the great comments👍🏻👍🏻🛠
Cheers mate, just moved into a new flat here in Stockholm with a blown bulb and wondered why it was so hard just to unscrew it!
Thanks for the great comments👍🏻👍🏻🛠
5 years later , same shop, same bulbs….4.98. Thank you for video!
😂 Thanks for the great comments👍🏻👍🏻🛠
Thanks, after seeing your video i used an Irwin Quick Grip Mini which has plastic jaws to get a purchase on the lamp cover and get it shifted.
Glad I could help Thanks for the great information👍🏻👍🏻🛠
@@aaanton11 I had just about given up until I saw what you had done.
Leave the oven on 200 degrees centigrade for three minutes to heat up the grease that has caked the glass cover. Then with rubber gloves you should be able to twist it off anti-clockwise.
Thanks for the great information👍🏻👍🏻🛠
Good video. I had the same problem but used a hairdryer on the light surrounding and that loosened it up. Two oven bulbs from Asda for £2 sorted! Cheers.
Great tip!, Thanks for the great comments👍🏻👍🏻🛠
Exactly my problem great tutorial many thanks .
Thanks for the great comments👍🏻👍🏻🛠
Just tried this and it worked perfectly; thank you so much
Thanks for the great comments👍🏻👍🏻🛠
Gee, man, thanks so much for this practical solution. Much appreciated you taking the effort !
You're welcome! Thanks for the great comments👍🏻👍🏻🛠
Thanks for the tip, you showed me that it is possible :) Anyway, I didn't have the tool so eventually I used WD-40 spray as a WA
Glad I could help! Thanks for the great comments👍🏻👍🏻🛠
Brilliant job, give me confidence to do mine now. 👌🏻
Thanks for the great comments👍🏻👍🏻🛠
Hi, we tried everything, degreaser, special tool, rubber gloves, WD 40 and nothing worked. Tried this and it worked straight away. Good help thanks.
well done Thanks for the great comments👍🏻👍🏻🛠
Brilliant thanku for sharing I’ve been with out mine for months.
Thanks for the great comments👍🏻👍🏻🛠
Thank you! Next time you could try an oil filter opener from your car maintenance playlist :-).
I like the grips😂 but great shout, Thanks for the great comments👍🏻👍🏻🛠
Bingo. I needed to change my bulb and there you are to the recue.....Again!
😂😂 I cant help myself Thanks for the great comments👍🏻👍🏻🛠
Thanks, that's very useful. I've been struggling to get the glass cover off by hand as it makes no mention of needing to use a pair of pliers in the instruction manual. Thanks also for the tips on using replacement bulbs.
The glass can be really tight, but it’s a good thickness so quite strong 💪🏻 thanks for the great comments 👍🏻👍🏻
@@aaanton11 I finally got it sorted with the plyers. Your video was very helpful. Thanks again.
Just put rubber gloves on and twist
I was able just to unscrew it with my hands and didn't need any grips. I'd suggest trying this first just in case. Took me 5 secs. Cleaned it with wire wool and washing up liquid. Worked just as well. Took 5 mins. My bulb says 240v and 40w. Phillips Poland. 300 deg EQ. D817 I THINK!?
However, I really appreciate the vid so I knew what to do in the first place!
Thanks for the great information👍🏻👍🏻🛠
@@aaanton11 it's people like you that make RUclips great. Thanks again.
Brilliant! Love the clarity of how to do it. Cheers
Glad it was helpful! Thanks for the great comments👍🏻👍🏻🛠
Thanks mate the wife's been nagging me for ages to do this 😂
No problem 👍 Thanks for the great comments👍🏻👍🏻🛠
Great. This the solution for my Juno oven. Thank you.
Glad I could help, Thanks for the great comments👍🏻👍🏻🛠
Thanks for sharing
My pleasure Thanks for the great comments👍🏻👍🏻🛠
Great tip. Amazes me why they make something so smooth so you can't get a grip with your hands!
Helped me out with your Aygo vids too (I've got a C1).
Glad I could help! Thanks for the great comments👍🏻👍🏻🛠
thanks , I found that original bulb is 40watt but this new one is 25watt and I wasn't sure if it will do the work.
Thanks for the great comments👍🏻👍🏻🛠
Thanks heaps 👍
No problem 👍 Thanks for the great comments👍🏻👍🏻🛠
Thank you! Your solution worked for me!
Glad it helped! Thanks for the great comments👍🏻👍🏻🛠
Old one is 40W !!! i just looked It woks also with the hand you don't need any tool , just a strong hand :))
Thanks for the great comments👍🏻👍🏻🛠
thanks for your advice
You're welcome! Thanks for the great comments👍🏻👍🏻🛠
Cheers Bro… going to try this
Have fun Thanks for the great comments👍🏻👍🏻🛠
Thanks very help, especially as there is no man about to do it for me! 🤣
Glad to help, Thanks for the great comments👍🏻👍🏻🛠
It worked really well. Thank you!
Thanks for the great comments 👍🏻👍🏻🛠
thanks
No problem Thanks for the great comments👍🏻👍🏻🛠
Brilliant mate, very helpful 👌🏼.
Glad it helped Thanks for the great comments👍🏻👍🏻🛠
Thank you. Any tips for removing a very stubborn stuck broken internal oven bulb, case only left in and stuck? Thanks again inadvance
warm the oven oven up, switch off, turn the power off, use long nose pliers to bend inner casing together and unscrew, Thanks for the great comments👍🏻👍🏻🛠
Thank you. Nice clear demo. One question though: the Bosch manual says use a Bosch bulb. Won't it compromise any guarantees if you use another brand (and something goes wrong later)?
No as long as the power rating is the same Thanks for the great comments👍🏻👍🏻🛠
Thanks, helpful DIY content!!!
Glad it was helpful! Thanks for the great comments👍🏻👍🏻🛠
Warm up the oven and it comes off easy
Thanks for the great information👍🏻👍🏻🛠
Great! Thank you!
You are welcome! Thanks for the great comments👍🏻👍🏻🛠
Hi there, can you please explain what products exactly did you use to clean the Bulb Cover once you had it successfully removed? Thanks.
I used this amzn.to/3TFOJaK Thanks for the great comments👍🏻👍🏻🛠
Worked well. Great. Thanks
Thanks for the great comments👍🏻👍🏻🛠
Bought the special tool. Worked well and the glass cover turned fairly easily.
However, it refuses to drop off its mounting.
Any suggestions?
It should drop once unscrewed, Thanks for the great comments👍🏻👍🏻🛠
If I had a pound for every expletive I used whilst trying and failing to get that glass cover off for nearly half an hour I could probably buy a decades worth of bulbs for the entire town.
I have been there, that's why I made the video, Thanks for the great comments👍🏻👍🏻🛠
You can take the glass cap off if you twist it hard enough with your hands. The cap is deliberately a glass dome that you can grab and unscrew, you don’t need pliers
Some are super tight, Thanks for the great comments👍🏻👍🏻🛠
Great stuff. 👍👍
Thanks for the great comments👍🏻👍🏻🛠
Thank you sir
Welcome Thanks for the great comments👍🏻👍🏻🛠
Worked for me, cheers
Thanks for the great comments 👍🏻👍🏻🛠
Hi Mate, what did you use to clean the glass oven bulb cover? Thanks for the video 😁
I find a wire brush works really well, thanks for the great comments 👍🏻👍🏻🛠
Thanks for a clear video. For me the bulb keeps turning round and round in the socket but doesn't bite. There is a metal washer which seems to have come out with the bulb - it fits over the bulb thread and covers about 2 turns of the thread. I can't work out how to get the washer back into the socket - I've tried inserting the bulb with the washer attached to it, but it doesn't bite. Any ideas? Thanks in advance.
There isn't normally a washer in there, try fitting it without it.Thanks for the great comments👍🏻👍🏻🛠
@@aaanton11 Thanks! Washer may be the wrong word - it looks like a washer but has a thread inside and outside of it, so it threads over the bulb but also into the fitting. I think the bulb threaded part was too narrow and this widens it. Anyway I've ordered the same bulbs that you used, which look wider than mine, so hopefully that will solve it.
@@aaanton11 Further to my reply from yesterday, I ordered the Philips 25W SES E14 bulb you suggested, but unfortunately the bulb base is too narrow and doesn't screw into the fitting. - it just keeps turning around. Is there an oven bulb which has a wider base? I looked for the E17 bulb online but it seems to be only for microwaves.
Thank you.
Thanks for the great comments👍🏻👍🏻🛠
🌟🌟🌟🌟🌟🌟Great advice Thanks ⭐⭐⭐⭐⭐⭐
You are so welcome Thanks for the great comments👍🏻👍🏻🛠
Thank q very useful
Thanks for the great comments 👍🏻👍🏻🛠
I'm looking at this for the first time, and had a question. There's a wire that holds the light cover in place (the cover is not a screw on, screw off type). I lost this wire, so can I use a coat hanger wire in place of it? I really don't want to jump through hoops in order to find a replacement.
I don’t see a problem making a wire, hope you have success, thanks for the great comments 👍🏻👍🏻
SET THE CLOCK!!! i worked for me bulb wasn't lighting might save u 4 hours😊
Thanks for the great information👍🏻👍🏻🛠
when you turning it by hand the meatal ring is moving with the cover thats whats happening with my neff would that be the same as bosch
They are generally all the same light units, Thanks for the great comments👍🏻👍🏻🛠
Many thanks for this video.......had tried by hand to remove the glass cover several times which was impossible & caused a great deal of stress, agitation & swearing......Had spoken with Bosch last week before seeing the video & they sold me a plastic removal tool & a new bulb at a cost of £15.80 !! The plastic removal tool is not much use when some imbecile at Bosch has torqued up the glass cover unit to the the same lb/ft as a car wheel nut !! Take a bow Bosch whilst I clap & blow a trumpet with a flag on it for a very poor design.....Thankfully my grips where large enough to fit round the glass cover & less than 30 seconds later the cover was off......a brilliant & simple solution to a unnecessary problem created Bosch.
well done, Thanks for the great comments👍🏻👍🏻🛠
Hi Anton, Great video demo. I am having an awful job trying to get my Neff bulb cover off with no joy. With no help from Neff other than a £99 call out fee. 😒😒😤. Where did you get your pliers from because I can’t find anything large enough to get the grip required. Please can you help and send link for where to purchase pliers.
Here is the link to the big grips, amzn.to/2M6SHoz, There is also the correct tool which is £7 Link is amzn.to/2TMUnry
Thanks for the great comments👍🏻👍🏻🛠
aaanton11 thanks Anton I have ordered tool as I have been advised that my model of Neff oven they do not have tool to fit. Great service from you though Anton. 👍🏾👍🏾👍🏾👍🏾
Topman thx
Thanks for the great comments👍🏻👍🏻🛠
Hi Anton, does the cover needing screwing clockwise or anti clockwise to get it off?
anti clockwise to remove, Thanks for the great comments👍🏻👍🏻🛠
counterclockwise?
or anti clockwise, Thanks for the great comments👍🏻👍🏻🛠
Hi, We just changed the 40 watt bulb in a bosch oven but the light still does not work. The old bulb was broken but we did manage to unscrew the metal bit to get the new bulb in. Any ideas why a new bulb would not work?
I would check the contacts in the bulb holder, Thanks for the great comments👍🏻👍🏻🛠
@@aaanton11 Thanks, we used some foil and it still did not turn on so gave up. After using the oven again 5 mins later the bulb turned on and now works every time!
If I had done this the grips would have slipped and ripped the element to bits.
Not true, but you can buy the tool link is in the video description Thanks for the great comments👍🏻👍🏻🛠
You dont need a tool at all. I put on a pair of rubber gloves and it came off no problem!!
wow you have a iron grip, Thanks for the great tip, this one was sooo tight, Thanks for the great comments👍🏻👍🏻🛠
Thx. It`s so easy use rubber gloves to screw the blub.
Rubber gloves did the trick, thanks
Any ideas on removing Smeg timer glass on front of oven to replace bulb anyone ?
not sure on that one sorry Thanks for the great comments👍🏻👍🏻🛠
Options for LED????
it would get too hot for a led, and I don't think it would last, Thanks for the great comments👍🏻👍🏻🛠
What a fucking design. I have to borrow some stilsons to do this!
Thanks for the great comments 👍🏻👍🏻🛠
@@aaanton11 I struggled for an hour last night trying to get the glass off without any success! I borrowed some stilsons off my plumber mate this morning and it took 2 seconds to break the seal and the thing unscrewed as in your video. My question is why does the glass have to lock? Why cant it simply unscrew from the beginning? They just want to sell you a £5 nylon tool that I hear doesn't work anyway!
doesnt work for me, the cover is stuck.
Try warm in the oven up first, before attempting to unscrew that will usually break the seal Thanks for the great comments👍🏻👍🏻🛠
My bulb blows my Fuse X 2, so does that mean an electrician can sort it, or does it have to be a cooker guy. Please reply ASAP as am desperate ( the cooker is still working though,).?
have you replaced the bulb? its a oven issue so oven guy if a new bulb doesn't work, Thanks for the great comments👍🏻👍🏻🛠
The original bulb was a 40w bulb.
Thanks for the great information👍🏻👍🏻🛠
how can any light get through the dirty glass cover. ICK. Clean your oven. Please......
I did clean the glass, did you not watch the video till the end 😂 Thanks for the great comments👍🏻👍🏻🛠
Rule number 1 - turn off the power!! The air is blue in this house, not only has the bulb blown into little pieces , hubby cannot for the life of him remove what is left to be able to replace the bulb.
You need to grab some long nose pliers, and try to pinch the edges of what's left, Thanks for the great comments👍🏻👍🏻🛠
Note to self: purchase ridiculously huge pliers.
Self: ok.
The bigger the better 😂, Thanks for the great comments👍🏻👍🏻🛠
Here is the easier way. Unscrew the glass cover with your hand wearing a latex glove. Worked like a charm.
Just unscrew it with your hand wearing a latex glove. Worked like a charm!
Great! Thank you!
You are welcome! Thanks for the great comments👍🏻👍🏻🛠