Late to the party as well. I have a 2019 Nissan Sentra base model and i just ordered and installed the Crux interface for my vehicle model. Made life SO much simpler! No guess work or wire hunting. Just wire it up, set the dip switches and plug it in. Retained factory backup cam, swc, factory usb and aux. To be fair the Crux interface wasn't released until October 2023 but still... for those hunting for a simpler solution you should head over to the Crux site and search their vehicle for the appropriate interface. Glad i did.
WORKS! Tho I Found a key detail, missed in my initial research: important IF you're adding butt- connectors or any other wires TO the SWC setup, since those can add resistance, cause the signal to fail! That's why mine took a few attempts, lol.. Good luck, all
Just to clarify, you don't need an extra SWI box if your car's SW buttons are the resistive type. If the controls go through the CAN bus a SWI box will be required.
My 2012 Acura TL does have resistive type steering wheel controls. Does that mean I don't need to buy that $70 box and I can do it with just the cables themselves?
@@CHiTO316 Most budget Chinese head units support learning your resistor values so a add-on module is not necessary. Generally name brand units are not programmable so a module would be required even if not on the CAN bus.
But haven't been happy with my ATOTO. They are the better of the Chinese units but glitches and still frequent. All others on the market are even worse. I've tried and returned MANY!
How should I know where should I connect this two wires k+ and the other one to my car harness I have 2017 Chevy express not sure how they name it nothing says streaming wheel on the diagram, can you tell me where should I connect them? Thanks for your video
What are the pin descriptions on the Lexus plug? I have a 2011 Honda into which I want to install an Atoto unit. There are two wires on the factory harness labeled "Remote switch", which is the signal wire and "Remote GND", which is a separate ground for the SWC. Does it match with whats on your harness?
My 2006 Lexus ES330 wiring diagram shows the 20 pin connector plugs into R3 with 4 wires signals as: R3 - 6 as SWG body ground (color is black/red) steering wheel ground R3 - 7 as SW1 steering wheel pad switch signal (color is pink/black) R3 - 8 as SW2 steering wheel pad switch signal (color is green/white)
Doesn't the atoto only have 1 ground. I connected mine to the Toyota wiring Harness. Is there an additional ground coming out of the Toyota 20 pin prong?
En mi ford focus son 2 cables que salen del mando del volante y del atoto hay 2 key, ne imagino seria conectar esos 2 pares de cables mas la tierra del arnes de la radio y buscar una tierra del coche, talvez asi pudiera funcionar, me hago una idea sobre el video
Thank you for sharing video. Can bus adapter only to steering wheel control. Or have another purpose. I faced same issue I plan to upgrade sound unit in my car mercedes r230 sl 500 with premium sound system Boss code 810 to ATOTO S8G2109UP-A / S8G2108U-A 10" FLOATING SCREEN. with use the remaining orginal sound system like, fiber optic amplifier systems D2B, steering wheel control, antenna oem, CD changer. And without cutting iso wire harness. Problem # Can bus not include atoto android head unit. D2B bus optical system converter not available Anttana adapter not available CD changer socket adapter not available Any help please. What I have options front me to safe rest of orginal system. Or delete all systems to atoto android can work fine. Waiting any help. Best regards,
If Logo Boot menu not appearing, ITS HIDDEN , in order to make it visible SET DATE to 2008-01-08 (Y/M/D) and TIME to 01:08 24 h, go back previous menu and it appears, got it from ATOTO Cust Serv. Good Day 0
Chad, that electrical wire is going to come loose after being in a baking car and then it's gonna short our your electrical system....I would fix that right away with crimp connectors.
Thank you sir, you saved me 65$.
It is working perfectly on my prius 2005 the way you explained.
Bro can explain the wire can i pug in 20 pin plug. Please 🙏
You rock! I have a 2005 Camry with JBL and this is literally the exact info I was looking for!
Late to the party but your video worked like a charm!!! Thank you so much
2004 RX330 wiring up a Atoto S8 Gen2
Late to the party as well. I have a 2019 Nissan Sentra base model and i just ordered and installed the Crux interface for my vehicle model. Made life SO much simpler! No guess work or wire hunting. Just wire it up, set the dip switches and plug it in. Retained factory backup cam, swc, factory usb and aux. To be fair the Crux interface wasn't released until October 2023 but still... for those hunting for a simpler solution you should head over to the Crux site and search their vehicle for the appropriate interface. Glad i did.
WORKS! Tho I Found a key detail, missed in my initial research: important IF you're adding butt- connectors or any other wires TO the SWC setup, since those can add resistance, cause the signal to fail! That's why mine took a few attempts, lol.. Good luck, all
Just to clarify, you don't need an extra SWI box if your car's SW buttons are the resistive type. If the controls go through the CAN bus a SWI box will be required.
My 2012 Acura TL does have resistive type steering wheel controls. Does that mean I don't need to buy that $70 box and I can do it with just the cables themselves?
@@CHiTO316 Most budget Chinese head units support learning your resistor values so a add-on module is not necessary. Generally name brand units are not programmable so a module would be required even if not on the CAN bus.
But haven't been happy with my ATOTO. They are the better of the Chinese units but glitches and still frequent. All others on the market are even worse. I've tried and returned MANY!
This is exactly what iam looking for. Will it work with alphine head units
Can you please identify what the green wire and the purple wire are (from the Lexus factory 20 pin wiring harness)? Thanks!
up !
How should I know where should I connect this two wires k+ and the other one to my car harness I have 2017 Chevy express not sure how they name it nothing says streaming wheel on the diagram, can you tell me where should I connect them? Thanks for your video
You need the car wiring diagrams for your car, they will identify which steering wheel buttons are connected to which wires in your car.
I try so many places but can’t figure it out, any idea how they name it? Thanks again
Can it all so work for Toyota verso and how we I do it?
What's the 3.5mm jack in back of the atoto harness for then?
Thats for a little box that allows wireless atoto swc to work
What are the pin descriptions on the Lexus plug? I have a 2011 Honda into which I want to install an Atoto unit. There are two wires on the factory harness labeled "Remote switch", which is the signal wire and "Remote GND", which is a separate ground for the SWC. Does it match with whats on your harness?
My 2006 Lexus ES330 wiring diagram shows the 20 pin connector plugs into R3 with 4 wires signals as:
R3 - 6 as SWG body ground (color is black/red) steering wheel ground
R3 - 7 as SW1 steering wheel pad switch signal (color is pink/black)
R3 - 8 as SW2 steering wheel pad switch signal (color is green/white)
Doesn't the atoto only have 1 ground. I connected mine to the Toyota wiring Harness. Is there an additional ground coming out of the Toyota 20 pin prong?
En mi ford focus son 2 cables que salen del mando del volante y del atoto hay 2 key, ne imagino seria conectar esos 2 pares de cables mas la tierra del arnes de la radio y buscar una tierra del coche, talvez asi pudiera funcionar, me hago una idea sobre el video
Hi i have a 2011 honda accord what would I need to make it work with out n adapter
Okay very 👍
Can you please explain to me about how to connect it to control my starter car and steering weel of Nissan qashqai 2007 model
Thank you for sharing video. Can bus adapter only to steering wheel control. Or have another purpose.
I faced same issue I plan to upgrade sound unit in my car mercedes r230 sl 500 with premium sound system Boss code 810 to ATOTO S8G2109UP-A / S8G2108U-A 10" FLOATING SCREEN. with use the remaining orginal sound system like, fiber optic amplifier systems D2B, steering wheel control, antenna oem, CD changer. And without cutting iso wire harness.
Problem #
Can bus not include atoto android head unit.
D2B bus optical system converter not available
Anttana adapter not available
CD changer socket adapter not available
Any help please.
What I have options front me to safe rest of orginal system.
Or delete all systems to atoto android can work fine.
Waiting any help.
Best regards,
If Logo Boot menu not appearing, ITS HIDDEN , in order to make it visible SET DATE to
2008-01-08 (Y/M/D) and TIME to 01:08 24 h, go back previous menu and it appears, got it from ATOTO Cust Serv. Good Day 0
Has anyone done this wit their 2012 Acura TL that can share how they wired it up?
How can I find ground wire
I’m assuming this will also work on the Toyota Camry 2007
I just installed mine on a Camry 2007, it works fine, so far.
@@pachuekoloko could please tell us how you wired the cables, I'm having some problems doing it
@@pachuekoloko thanks in advance. Btw I've got a second gen tundra Wich is the same wiring
@@guacaquio
Hey I just did mine on Camry 2011. Apparently the pink wire from Toyota is the Ground. Until I figured that out, nothing else was working.
@@Makeme-g8v thanks in my case I just had to reset the the button configuration in the unit
Putting an Atoto product in a Lexus sounds so wrong on so many levels, but this video was still entertaining to watch just the same.
Chad, that electrical wire is going to come loose after being in a baking car and then it's gonna short our your electrical system....I would fix that right away with crimp connectors.