To further answer your questions: 1. Which mounting hole on the VTX mount should the camera be installed on - we recommend the top one. This is to lower the camera position to further protect it from crashes. The video shows otherwise, but we do recommend you install the camera on the top mounting hole!😊 2. DJI controller could be used with the ELRS version of the whoop - please check out our product page description to configure accordingly😍
@@chuckliu2155 It's a bit long to explain here, but we have written it under the product page's FAQ section :) Check it out here: betafpv.com/products/pavo-pico-brushless-whoop
I purchased pavo pico (o3). I immediately set it up and test flew it. However, when flying, the plane tilted back to the left little by little. After 4 minutes of flight, it tilted about 30 degrees, so I had to "guess" the rudder at all times. The FC settings have not been changed from the factory settings. The transmitter used is a Betafpv LiteRadio3 (ELRS). The above phenomenon does not occur when the transmitter is used in a different aircraft, so we think the problem is with this aircraft or the FC. I have tried many times to calibrate horizontally. We have also confirmed that the main unit itself is not tilted. There is no problem with the weight balance of the main unit.
Short and to the point video on how to assemble the DJI O3. Thank you. Is there any instructions on how to connect to the Betaflight and set it up with my TX16s?? Thanks
It is light, agile and can fly smoothly. Choose manual exposure in O3 video settings such that the shutter speed is 2x that of frames per second (fps). For example, if you choose 4:3 2.7k/50, manually select 1/100 shutter speed, Add a suitable ND filter to make auto ISO close to 100. My footage (2.7k/50 1/100 4:3, stabilised with Gyroflow 1.5): ruclips.net/video/uYpGK_xCwOg/видео.html
Gmjust assembled my Pavo Pico with the o3 unit. Great build. Good quality and very well designed. My unit don't get any electricity. Do I have to activate something?
the O3 only works with the new grey gamepad style DJI radio. If you swap the video antennas as they do at 1:00 then it won't work, the RC link works on 2.4GHz and the original DJI antenna is dual band whereas the small ones are only 5.8. IIRC there's a mount included to use the stock DJI antenna, at which point it should be fine as the plug they use for the AU seems to have the additional SBUS wires installed, so they are probably wired up at the other end.
@@FordTom What a surprise! This was a blind spot. So, if I use the DJI RC2, I need to install the stock antenna that comes with the O3 AirUnit? By the way, what is "AU"? I would be glad if you could tell me.
@@dLab AU is air unit :) and yes you'll need to use the stock antenna as far as I know. I'm actually not 100% sure the RC2 can't use the same 5.8GHz link that the video uses but I think it can't
Thanks for your video. How about binding the o3 air unit to the DJI Googles 2. I tried to bind but nothing is happening. Can i do it via DJI App or Betaflight?
Man, I'm trying to figure out the walksnail version over here, seems like I need to take the camera off the vtx to guide it through the front of the frame?
Eu quero de mais esse negócio só não sei configurar mas vou consigui preciso saber qual configuração devo pedir na compra pra usar radio e óculos googos 2 dji se alguém pode me ajudar agradeço
I just got some of the Tattu R-Line 2s 550mah and they do not fit the battery holder as is. I bought a backup frame so I just tried cutting the bottoms of the 2 "loops" and they can now fit and are held pretty securely, but will probably throw a Velcro strap on to be sure.
Received the Pico (TBS version!) today, binding with Tango 2 doesn‘t work, binding with Radiomaster TX16S with ELRS did work, but no reaction in Betaflight. Same with DJI FPV Controller 2, binding worked but no reaction in Betaflight. Enough for today.😡
In most cases wrong wiring. Had the same topic: The O3 must be wired to Bat+ instead of +5V. The instructions of BETAFPV are simply wrong or misleading.
I have another Pavo Pico O3 video shoot at 2.7k/100fps 4:3, stabilised with Gyroflow 1.5, then slower down to 50% speed with LumaFusion: ruclips.net/video/5jI6hqAvOH0/видео.html
To further answer your questions:
1. Which mounting hole on the VTX mount should the camera be installed on - we recommend the top one. This is to lower the camera position to further protect it from crashes. The video shows otherwise, but we do recommend you install the camera on the top mounting hole!😊
2. DJI controller could be used with the ELRS version of the whoop - please check out our product page description to configure accordingly😍
im very interested, i want to know how to link the DJI controller with this drone thx
@@chuckliu2155 It's a bit long to explain here, but we have written it under the product page's FAQ section :)
Check it out here: betafpv.com/products/pavo-pico-brushless-whoop
@@BETAFPVHobby a video would be very helpful please please please
@Mert D Video is out!
@@BETAFPVHobby Can’t find video Link Please!
Thank you for such a great short to the point video. Perfect length in my opinion
I purchased pavo pico (o3).
I immediately set it up and test flew it.
However, when flying, the plane tilted back to the left little by little.
After 4 minutes of flight, it tilted about 30 degrees, so I had to "guess" the rudder at all times.
The FC settings have not been changed from the factory settings.
The transmitter used is a Betafpv LiteRadio3 (ELRS).
The above phenomenon does not occur when the transmitter is used in a different aircraft, so we think the problem is with this aircraft or the FC.
I have tried many times to calibrate horizontally.
We have also confirmed that the main unit itself is not tilted.
There is no problem with the weight balance of the main unit.
Could you dm us on facebook and send in a video so we could have a closer look with our support team to see what is exactly happening? Thank you!
Short and to the point video on how to assemble the DJI O3. Thank you. Is there any instructions on how to connect to the Betaflight and set it up with my TX16s?? Thanks
Thank you. With some steps, I had assembled wrong then followed your video. All the vibrations are gone!
It is light, agile and can fly smoothly. Choose manual exposure in O3 video settings such that the shutter speed is 2x that of frames per second (fps). For example, if you choose 4:3 2.7k/50, manually select 1/100 shutter speed, Add a suitable ND filter to make auto ISO close to 100. My footage (2.7k/50 1/100 4:3, stabilised with Gyroflow 1.5):
ruclips.net/video/uYpGK_xCwOg/видео.html
Gmjust assembled my Pavo Pico with the o3 unit. Great build. Good quality and very well designed. My unit don't get any electricity. Do I have to activate something?
Did you figure out?
Is there some trick to installing the rubber isolation bumpers [1:38] into the frame? I've destroyed two of them trying.
I immediately purchased two units.
By the way, can I use a DJI radio with the FC that comes with this kit?
the O3 only works with the new grey gamepad style DJI radio. If you swap the video antennas as they do at 1:00 then it won't work, the RC link works on 2.4GHz and the original DJI antenna is dual band whereas the small ones are only 5.8. IIRC there's a mount included to use the stock DJI antenna, at which point it should be fine as the plug they use for the AU seems to have the additional SBUS wires installed, so they are probably wired up at the other end.
@@FordTom What a surprise! This was a blind spot. So, if I use the DJI RC2, I need to install the stock antenna that comes with the O3 AirUnit? By the way, what is "AU"? I would be glad if you could tell me.
@@dLab AU is air unit :) and yes you'll need to use the stock antenna as far as I know. I'm actually not 100% sure the RC2 can't use the same 5.8GHz link that the video uses but I think it can't
@@FordTom Any chance you can give further instructions on how to use the DJI grey controller? Their instructions are piss poor.
@@SpartanOfLuxon afraid I don't have any clue how to set one up as I don't use it :)
Please do you have any video for walksnail installation?
Thanks for your video. How about binding the o3 air unit to the DJI Googles 2. I tried to bind but nothing is happening. Can i do it via DJI App or Betaflight?
Any video for walksnail installation?
SO much FUN!❤❤
My antennas that came in with my kit has the plastic covered all the way the white part of the antenna with the heat shrink
Presumbly if using it as a pnp there is no betaflight configuration necessary? Or do I need to select sbus baud=fast in the goggles and on the baord?
How can I start/stop the record in the O3 air unit? I'm using a ELRS remote (Jumper T-PRO). Thanks!
I have DJI RC2 and DJI Googles v2 what need to buy else for fly? BETAFPV Pavo Pico + o3 unit?
То есть для того чтобы соединить Pavo Pico и Dji 03 не нужно ничего клеить и паять?
Is there a way to use my dji fpv goggles v1 in this 03 unit.thanks
Can you use DJI Avata controller and headset with that?
Do I need to solder the dji o3 air unit?
Hello it would be necessary to make the same video but for Walksnail avatar V2.
what happens if i dont install the rubber dumpper?looks impossible for now
Will mounting a naked GoPro here result in a significant decrease in stability?
Man, I'm trying to figure out the walksnail version over here, seems like I need to take the camera off the vtx to guide it through the front of the frame?
I thought you needed to use the DJI 03 antenna to be able to fly with the DJI remote 2?
Great explanation!
But what about configure in betaflight and dji o3 ? Im new in fpv, flying dji fpv to this time , but I got now pavo pico and dji o3 with it
Betafpv Pavo pico TBS DJI O3 VTX works with the remote control TBS Tango 2?
+1
works
is this setup for this and binding the same for pavo20? I don't see a guide for pavo20 specifically
Dear Betafpv,
If I purchase ELRS DJI O3 version, can I switch use my ELRS controller & DJI FPV Controller 2?
what about in cetus x?
Which rx version do you recommend for using the Dji O3
Depends on the RC you have! If you are intend to use the DJI RC2, choose the cheaper one....
Eu quero de mais esse negócio só não sei configurar mas vou consigui preciso saber qual configuração devo pedir na compra pra usar radio e óculos googos 2 dji se alguém pode me ajudar agradeço
What about if you wanted to bind the DJI Controller 2 to the quad?
it will if you use the dji 03
Guys i Love your products. Please consider me as a kol or reviewer. Yahooooooooo..
Mikey
If I use the O3 Air Unit, does it matter which rx I choose when purchasing the kit?
That simply depends on your RC!
When are you going to ship it? I already placed my order two days ago. Can't wait 😃
ive been waiting for mine since 19 may
@@-alpha- mine is just arrived in my country. Maybe in the end of this week it will be here
mini avata. I like thiis
no way to mount decased O3 VTx?
thanks for the video, does the pico include fc and motors?
Sure! Everything included except DJI O3 Air Unit and camera.
Looks good 👍👌
Can I use my RC V2 DJI instead of ELRS?
Of course, no problem, if you have the older FC (V3 or 2.2) choose SBUS and UART6, if you have the newer FC (1.0) choose UART5 instead!
Hi all, does anyone know if the "Tattu R-Line 2s 550mAh" will also fit to thsi quad?
Thank and happy low weights flights :D
I just got some of the Tattu R-Line 2s 550mah and they do not fit the battery holder as is. I bought a backup frame so I just tried cutting the bottoms of the 2 "loops" and they can now fit and are held pretty securely, but will probably throw a Velcro strap on to be sure.
Received the Pico (TBS version!) today, binding with Tango 2 doesn‘t work, binding with Radiomaster TX16S with ELRS did work, but no reaction in Betaflight. Same with DJI FPV Controller 2, binding worked but no reaction in Betaflight.
Enough for today.😡
Problem solved: Tango 2 Firmware was too old.🙈
Why my pico have no power in O3 , what can I do ???
In most cases wrong wiring. Had the same topic: The O3 must be wired to Bat+ instead of +5V. The instructions of BETAFPV are simply wrong or misleading.
how do we know it's correctly wired?
My dream fpv.......❤️❤️❤️
105$ only for the frame Or all components ?
all components w/o dji 03
@@Twx97 whaaaaaaatttt ???? Lol in polish market dji o3 cost about 286 dollars loooooool
@@Twx97 aaaah you mean without djo o3
@@damianwyczakowski2491 yep
@@damianwyczakowski2491 sadly that's the cost for flying with dji
I have another Pavo Pico O3 video shoot at 2.7k/100fps 4:3, stabilised with Gyroflow 1.5, then slower down to 50% speed with LumaFusion:
ruclips.net/video/5jI6hqAvOH0/видео.html
It’s not working
Pls help
Definitely dont work like that