Can be used on most Bafang motors. However, other than motor calibration, there was no reason to make detailed adjustments while using the motor. The power of this motor is strong enough to break the chain.
Yes. If you overhaul and remove stator, you will need it to calibrate. (I'm told) it works on UART only. No CANBUS. The motor is not (laughing hard) powerful enough to break quality (Shimano M8000 compatible) chains. I run my Ultra at 230nm w/ Innotrace X1 Controller, so not an opinion. A fact. Yes , the BESST tool works as advertised.
@@paulwalker3563 I was told I was told I was told.... Thats kinda boring to be honest. Either you know or not. If you KNOW something for sure, let us participate, if you dont know, pls do us a favor and just keep quiet Doesnt helb anyone if you're just guessing... BTW whhy do you think the BESST Tool comes with triangle (CAN) and round (UART) connectors at the same time?!? You can guess again.... maybe its becaus it supports bith of them?? ...but anyway, I'm just guessing 😀
@@barrykeane9864 Yes ma'am. I KNOW for a fact (1) I was told, (2) that you didn't ask the question (3) I don't owe you a favor, (4) the only 'us' I see is you and that mouse in your pocket and (5) I didn't address you, down there in mom's basement.
my ultra had error 30 and would only run for 8 minutes. II put in a new controller correctly. It ran for about 5 seconds I heard engine but no power to wheel. Then everything powered off. I put the old controller in. It still wont turn on. I also tried new display. Do you know what could be the problem?
buenas! muy bueno el video. que aplicancion o programa se usa ?
Awesome content cheers👍
How do you get the stator out
This could be very helpful, thanks
👍🏼
Is this BESST tool useful for the M620 UART too? Thank you!
Can be used on most Bafang motors. However, other than motor calibration, there was no reason to make detailed adjustments while using the motor. The power of this motor is strong enough to break the chain.
@@Mobilant_US Thank you!
Yes. If you overhaul and remove stator, you will need it to calibrate.
(I'm told) it works on UART only. No CANBUS.
The motor is not (laughing hard) powerful enough to break quality (Shimano M8000 compatible) chains. I run my Ultra at 230nm w/ Innotrace X1 Controller, so not an opinion. A fact.
Yes , the BESST tool works as advertised.
@@paulwalker3563 I was told I was told I was told....
Thats kinda boring to be honest.
Either you know or not. If you KNOW something for sure, let us participate, if you dont know, pls do us a favor and just keep quiet
Doesnt helb anyone if you're just guessing...
BTW whhy do you think the BESST Tool comes with triangle (CAN) and round (UART) connectors at the same time?!?
You can guess again....
maybe its becaus it supports bith of them??
...but anyway, I'm just guessing 😀
@@barrykeane9864 Yes ma'am. I KNOW for a fact (1) I was told, (2) that you didn't ask the question (3) I don't owe you a favor, (4) the only 'us' I see is you and that mouse in your pocket and (5) I didn't address you, down there in mom's basement.
my ultra had error 30 and would only run for 8 minutes. II put in a new controller correctly. It ran for about 5 seconds I heard engine but no power to wheel. Then everything powered off. I put the old controller in. It still wont turn on. I also tried new display. Do you know what could be the problem?
Calibration is required.
Where do you get parts for this motor?
www.greenbikekit.com/ I recommend this place.
Bon chons