На кроссовых мотоциклах звезды из дюрали, которая даже при Т6 не прочнее сырой стали. Так что на сезон хватает, а при такой цене как у индусов можно покупать их хоть каждый месяц.
@@user-bv5nr3yh4l как для меня, каждый месяц долбиться с тем, что менять звёзды это неприемлемо. Я стараюсь устанавливать более качественные детали, чтобы не тратить много свободного времени на замену дешёвых запчастей.
@@serbeer1240 тоже удивился - почему штампануть зубы сразу, а потом только подправить. А так получается ерунда - сыромятная звезда. Если её твердости достаточно для срока службы, то в подкаленом виде она могла бы быть вдвое тоньше!
1:12 Yikes. Each one of those sprockets must be "uniquely" balanced. No way those 4 spokes are punched symmetrically just by eyeballing them. It's also weird that they have such an empirical and error-prone step in a shop that even has a CNC machine. Besides, they are already using a punch press for the other holes. Why not one with 4-spoke pattern?
@@candlestyx8517 Then again those will (hopefully) only be used locally in aging Royal Enfields and Tuk-tuks topping 50-60 km/h and spending most of their time put-putting in traffic, so they can get away with the sloppiness. It's not like they'll end up being used on a Busa.
@Velktron it is visible that there is located some kind of bolt on the right which is playing the role of the pointer. But anyway it still does not work ideally.
It’s really very hard job for lively hood. Workers should be given protective gears & the Employer should take care of workers needs. I salute their hard job.
Those workers are very good at what they do and impressive how hard and efficient they work but someone needs to help provide safety glasses, gloves, and boots. Scary to think how many workers might be missing fingers toes or who are blind because of lack of minimal safety gear.
Nesse ramo, da metalúrgica sempre fico estasiado com tamanha capacidade do ser humano se reinventar... Parabéns ao heróis, que conseguem extrair o máximo do mínimo, pois estão expostos a diversas situações de perigo aonde com certeza o lucro é colocado acima do trabalhador.... Sendo mão de obra, descartável muitos irão se manifestar porém vamos nos colocar no lugar destes heróis e alguns podem ou não sofrer acidentes sérios.... Parabéns aos Heróis....
Что-то ерунда какая-то Дырки сверлит без шаблона в рандомных местах, метал сырой прокат звезду не калят! Приходилось бывать в цехе где делали звезды для ИЖей, на лесозаводской зарекой кто знает, там печка была размером с частный дом
It's very hard & risky job, they should wear good type of hand gloves, so as to avoid any physical injury. I really appreciate their risky job. Pls take all orecaution while working. Hats off. God bless them.
Proper manufacturing steps. Right from blanking, normalising, punching ,planishing ,ID OD machining, gear hobbing, face relief champhering. Tumbling to remove burr everything in one place the sweat reflects on the jobs produced. Salaam from 🇮🇳
Are you sure you do? It would mean people in the US would get paid about half as much, and about half of US don't even really work hard (that's being generous), so people wouldn't be able to have such cushy lives in the US or have the latest phones (at least without sacrificing air conditioning). We could just buy US made, but we don't because we are cheap and we say we want things but we vote with our wallets. Most of that was pretty safe except one machine which it's function I didn't even see what it was doing (then again my phone screen is cracked into a lot of pieces so it's a bit tricky either way, but I hate replacing a phone when I could just repair it if the parts are available)
@@jakegarrett8109 your comment just explained what the "civilised occident" is all about! We all want the good in the world until it comes to our plate.
@@mirceaalex9907 Yep, and probably 99% of people just don't know how good we have it. At least in the US we are extremely spoiled. Even a homeless guy had the audacity to ask me for like $80 more after I gave him all I had so he could sleep in a hotel, and it was the nicest weather imaginable and I sleep on a $20 air mattress I got as a gift... Like is he "homeless", or more just on a luxury cruise in life (because around here they get plenty of benefits, its like a rock concert tour except you don't have to work to pay for the hotels and free drugs!)
@@r.g.f.9904 existe lugares no mundo que é simplesmente sobrevivência e é que mostram ainda na internet pois existe lugares piores . Como vemos no vídeo deve ser na Índia não existe recursos como exemplo aqui e não tem alternativa e usar que existe e particularmente são bem inteligentes em com tão pouco recurso e conseguir até exportar seus produtos...são heróis.
Trabalho em uma fábrica que faz essa coroa da Moto Honda, agora os equipamentos são mais modernos, mais eles também estão de parabéns fazendo o melhor que podem nas condições que tem.
Muito legal ver os equipamentos próprios para a produção... Já fiz artesanalmente alguns e dá um trabalho do caramba, cortar na medida correta com esmerilhadera, tico tico, fazer os dentes usando o molde e depois com a micro retifica e depois ainda fazer a tempera da peça... Coisa de doido fazer isso em casa kkk mesmo assim ficou exelente só n tive como galvanizar, meti tinta preta de alta temperatura e pronto
Nunca mais vou reclamar do preço de uma "relação" na loja. Rsrs.. muito trabalho.. tem que ser valorizado..rsrs com uma boa qualidade é claro.. Párabens !
É quase assim, o processo produtivo está bem mais evoluído, não é necessário diversas pessoas para manipular uma chapa inteira para estampar os blancs, são usadas tiras de chapa em sistemas de estampo progressivo, como foi mostrado no vídeo é quase artesanal, hoje entra a fita de aço de um lado e sai a roda dentada do outro.
Да, а куда деваться людям, которые хотят трудиться, хотят работать и зарабатывать на жизнь!? Долой робототехнику, даёшь труд народа, на благо Родины и мира во всем мире!
Nice work, little tweaking and uniforms, boots, glasses, and you will have a world class shop and the pay to go along with it. Poor guy at the end could screw the whole job with one little manual mistake to the bolt hole patterns.
![A Boogie Wit da Hoodie - Body (feat. Cash Cobain) [Official Music Video]](http://i.ytimg.com/vi/RMT3AlAs0r8/mqdefault.jpg)
Условия труда и техника безопасности - на высшем уровне)
Not heat treated and not case hardened. With that kind of work this shop will stay in business forever.
見てて涙が出そう
スプロケってほぼ機械が自動で作ってると思ってました。こんな人海戦術で、素手で保護具も無しで作業されているのを見てしまうと感謝して大事に使わないといけないな、と思います。歯の部分なんて歯の形にプレスで抜いてると想像してました。
本当に勉強になりました。
ah daccord
It can be done ✔️ but it's called Fine Blanking 🙂
М-да уж, нужна закалка и качество - для этого есть другие производители. А мы как всегда ищем подешевле... 😜
На кроссовых мотоциклах звезды из дюрали, которая даже при Т6 не прочнее сырой стали. Так что на сезон хватает, а при такой цене как у индусов можно покупать их хоть каждый месяц.
@@user-bv5nr3yh4l the video is from Pakistan not India.
@@user-bv5nr3yh4l как для меня, каждый месяц долбиться с тем, что менять звёзды это неприемлемо. Я стараюсь устанавливать более качественные детали, чтобы не тратить много свободного времени на замену дешёвых запчастей.
@@Evge-n погоди, севшая звезда утянет за собой и вторую звезду и цепь ;)
Deve ser aço 1045 não é nescessário endurecimento
Делают всё на глаз
Похоже, что у ЧПУшника самая зачетная работа))
зато до этого столько брака никакой точности )
думаю проще сделать матрицу и сразу вырубать шестерню с зубьями потом заусенцы снять и все ))
@@serbeer1240 так им ещё надо, чтоб в этом процессе участвовало много рабочих))
Hello
@@serbeer1240 тоже удивился - почему штампануть зубы сразу, а потом только подправить.
А так получается ерунда - сыромятная звезда. Если её твердости достаточно для срока службы, то в подкаленом виде она могла бы быть вдвое тоньше!
Не перчатки не формы удивляюсь - респект!
Ищё и курить можно хоть где)
@@user-fi6mh6st8y да там и поссать можно прямо у станка 😂
сплошной брак )))
Можешь лучше ?
আলহামদুলিল্লাহ , আপনি ভালো কিছু জানলে অন্যকে শেখান, নিশ্চই ঐ ভালোটা এক দিন আপনার উপকার এ,লাগতে পারে,
А как же процесс закалки зубьев, без этого данная звезда долго не прослужит.
yes
صناعة ممتازة بمهارة فائقة واصلوا على هذا المنوال.
um processo louco mais é massa parabéns profissionais 👏🏽👏🏽👏🏽👏🏽
Quality work and nicely finished sprockets that will give good service.
Đẹp
.
А где термо обработка?
_и так сойдёт 😉_
До термообработки ещё 100 лет эволюции
Думаю, для тех апаратов с 50кубами можно и без.
ماشاء الله 🌷🇩🇿
Very conventional method of manufacturing sprockets.
I liked it!
excelente! parabéns! Brasil
Parabéns pelo excelente trabalho.
this is the first time i can see a process like this...
1:12 Yikes. Each one of those sprockets must be "uniquely" balanced. No way those 4 spokes are punched symmetrically just by eyeballing them. It's also weird that they have such an empirical and error-prone step in a shop that even has a CNC machine. Besides, they are already using a punch press for the other holes. Why not one with 4-spoke pattern?
I was thinking the same thing. As the owner of an aerospace machine shop, these parts would all be rejected. 😂
The biggest sin in my eyes is running them on the lathe without indicating them. No way they will be good parts
@@candlestyx8517 Then again those will (hopefully) only be used locally in aging Royal Enfields and Tuk-tuks topping 50-60 km/h and spending most of their time put-putting in traffic, so they can get away with the sloppiness. It's not like they'll end up being used on a Busa.
@Velktron it is visible that there is located some kind of bolt on the right which is playing the role of the pointer. But anyway it still does not work ideally.
Load shedding and customer demand in C grade parts
Excellent work.... great video
Beste Zeit, um einen Investitionsplan zu starten
It’s really very hard job for lively hood. Workers should be given protective gears & the Employer should take care of workers needs. I salute their hard job.
It really is amazing how stuff is made
E barato pelo trabalho que dá 👏👏👏
Impresionante las máquinas que tienen, buenísimo
जय श्री राम भाई
Very Helpful video
А термообробка?
I am in awe of their skills and sorry for the lack of safety equipment and practices.
Да если им дать хорошие ,современные станки они наверно весь мир перевернут 🤗🤔😊
@@user-yx8rz8xg2v post in English I don't understand Russian
@@imac786 é só usar o tradutor
@@user-yx8rz8xg2v ที่รัสเซียมีสงคราม
@@user-yx8rz8xg2v 2
بًأّکْسِـتٌـأّنِ ﺰنِدٍ بًأّدٍ 🇵🇰💪🏻
Veo muchos videos de fábricas distintas así sencillas , y veo q este país será la nueva potencia en pocos años.
Excepcional 👏😁
Maravilha gostei, como Deus deu sabedoria ao homem.
Muito bom é incrível o modo de como são feitos , nunca tinha visto isso é demmmmmais
Those workers are very good at what they do and impressive how hard and efficient they work but someone needs to help provide safety glasses, gloves, and boots. Scary to think how many workers might be missing fingers toes or who are blind because of lack of minimal safety gear.
Foreign countries have no such laws and much cheaper to produce products on top of very low pay.
@@gc1172 And in the EU or USA we just watch.... and still complain why everything is so expensive...
Mndbcecompanay90sp
I was gonna say the same thing, safety is job number one!
Nesse ramo, da metalúrgica sempre fico estasiado com tamanha capacidade do ser humano se reinventar...
Parabéns ao heróis, que conseguem extrair o máximo do mínimo, pois estão expostos a diversas situações de perigo aonde com certeza o lucro é colocado acima do trabalhador....
Sendo mão de obra, descartável muitos irão se manifestar porém vamos nos colocar no lugar destes heróis e alguns podem ou não sofrer acidentes sérios....
Parabéns aos Heróis....
خءعع
Tambem admiro esses indianos. Tem um conhecimento muito apurado
Me encantan estos videos por la comodidad En qué trabajan y por la seguridad industrial y que se avientan
Tuyệt vời quá cảm ơn bạn đã chia sẻ video phụ tùng xe đạp 🚲🚲🚲
Well done, Made in Pakistan. Stay Blessed. Masha Allah.
Asi videos bana sakta ha koi..500.rope 1 video ka donga
без закалки с листового железа марки ст3, ясно почему так быстро канчаются некоторые детали
Good idea God bless
❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤
This Young Guy is Brilliant in Repairing Hydraulic Pumps
❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤
الحمدالله پاکستان خیلی صنعتی هست
Что-то ерунда какая-то
Дырки сверлит без шаблона в рандомных местах, метал сырой прокат звезду не калят!
Приходилось бывать в цехе где делали звезды для ИЖей, на лесозаводской зарекой кто знает, там печка была размером с частный дом
А им похуй
Так они и ходят не много, и стоят дёшево
Это же мадем им кетаи
поэтому и хватает на месяц
Там сверху звездочка размечена
São guerreiros lindo trabalho
Super
It's very hard & risky job, they should wear good type of hand gloves, so as to avoid any physical injury. I really appreciate their risky job. Pls take all orecaution while working. Hats off. God bless them.
Proper manufacturing steps. Right from blanking, normalising, punching ,planishing ,ID OD machining, gear hobbing, face relief champhering.
Tumbling to remove burr everything in one place the sweat reflects on the jobs produced. Salaam from 🇮🇳
You are one of nice Indian people. Love from Pakistan:)
Voçeis são os melhores 👏👏👏👍👍👍🙏🙏🙏
Good job....Its really Very hard work to prepare a... Sprocket.
Show de fabricação....Belo trabalho de cada um deles
👏👏👏pelo trabalho perfeito.
Povo Trabalhador. Parabéns
Since birth firstime to see FROM BONGLOVERS CHANNEL yt laagan
Muito interessante mesmo essa fabricação de coroa. Parabéns pessoal pelo trabalho e dedicação
Kkk
N. Vvbnm
Unimaginable work conditions. I wish we lived in world where these people could work they're jobs safely and make the money they deserve for the work.
Are you sure you do? It would mean people in the US would get paid about half as much, and about half of US don't even really work hard (that's being generous), so people wouldn't be able to have such cushy lives in the US or have the latest phones (at least without sacrificing air conditioning).
We could just buy US made, but we don't because we are cheap and we say we want things but we vote with our wallets. Most of that was pretty safe except one machine which it's function I didn't even see what it was doing (then again my phone screen is cracked into a lot of pieces so it's a bit tricky either way, but I hate replacing a phone when I could just repair it if the parts are available)
FďđďďďčP
@@jakegarrett8109 your comment just explained what the "civilised occident" is all about! We all want the good in the world until it comes to our plate.
@@mirceaalex9907 Yep, and probably 99% of people just don't know how good we have it. At least in the US we are extremely spoiled.
Even a homeless guy had the audacity to ask me for like $80 more after I gave him all I had so he could sleep in a hotel, and it was the nicest weather imaginable and I sleep on a $20 air mattress I got as a gift... Like is he "homeless", or more just on a luxury cruise in life (because around here they get plenty of benefits, its like a rock concert tour except you don't have to work to pay for the hotels and free drugs!)
You sound spoiled 😂
It is the production of motorcycle sprockets.wonderful Follow the show, like it very much.👆👆👆👍👍👍🤟🤟📌📌📌📌📌👆
Wooow very Nice 👍👍👍👏👏👏
Se fosse aqui no brasileiro o sindicato já tinha parado a produção pra fazer greve .
Com o nível de exploração que essas pessoas estão sofrendo, com certeza. Basta olhar o estado do trabalhadores e o ambiente insalubre.
@@r.g.f.9904 existe lugares no mundo que é simplesmente sobrevivência e é que mostram ainda na internet pois existe lugares piores . Como vemos no vídeo deve ser na Índia não existe recursos como exemplo aqui e não tem alternativa e usar que existe e particularmente são bem inteligentes em com tão pouco recurso e conseguir até exportar seus produtos...são heróis.
Trabalho em uma fábrica que faz essa coroa da Moto Honda, agora os equipamentos são mais modernos, mais eles também estão de parabéns fazendo o melhor que podem nas condições que tem.
@Ryan Oliveira olá Ela só vende direto pra Honda
@Ryan Oliveira ooĺooòòooòòoò0p
@Ryan Oliveira If you are interested in buying goods manufactured in Turkey, provide me with your request
@@isaalisa4117 السلام عليكم
أين مقيم أنت
@@ivisoniranio6572 qual o nome da empresa ?
Bhoot khoob love from kashmir
Muito bom 👍
Muito bom 👍🇧🇷
Muito legal ver os equipamentos próprios para a produção...
Já fiz artesanalmente alguns e dá um trabalho do caramba, cortar na medida correta com esmerilhadera, tico tico, fazer os dentes usando o molde e depois com a micro retifica e depois ainda fazer a tempera da peça... Coisa de doido fazer isso em casa kkk mesmo assim ficou exelente só n tive como galvanizar, meti tinta preta de alta temperatura e pronto
Gh
778i
@@AjayKumar-nb1hn घ
動作要快 以前有作過十機年 很危險的工作 而且好累😴又很重 小心手 加油🥰🥰🥰
Super genial, mucho que aprender viéndolos trabajar
Puxa vida,o caras trabalham bem, mas é uma pena a falta de EPIs!
Epis é frescura só no Brasil mesmo!
Nota 1000 para os EPIS. Trabalho com seguranca e prevenção de acidentes é outro nivel.
Denuncie eles no ministério do trabalho!
@@brunodiassf9377 não me parece fábrica no território brasileiro para ter a possibilidade de denúncia ao Ministério do Trabalho.
@@wes8853 mas denunciei, vai que cola
Trabalhando de sandália
Epi é pra amadores .
Where everyday is flip flop Friday!
انه عمل ممتاز وانته عامل فني شكراا
Excelente gostei 👍 de ver.
Nunca mais vou reclamar do preço de uma "relação" na loja. Rsrs.. muito trabalho.. tem que ser valorizado..rsrs com uma boa qualidade é claro.. Párabens !
Ààa
Imagina o investimento quê é pra comprar uma máquina dessas. Tomara que o retorno seja bom 🙏
Thật không tưởng tượng, nhìn bạn làm rất là nhanh, tặng bạn một like chúc các bạn mạnh khỏe bình an trong cuộc sống 🤝👍👍👍👍
👍👍👍👍👌крутяК!
Nunca imaginei que fosse esse processo. Pensei que tinha forma que jogava o metal dentro. Parabéns aos profissionais
Formidable
Szacunek dla tych ludzi za pracę
+
dokładnie
Massa. 👏👏👏
Very nice👍👍
Formidável muito profissionalismo e maquinários.
Paulo tmj
Nabar van
gostaria que essa fábrica fosse do lado da minha casa muito show
Think like me, uncle, I love this job
хорошая работа... но труд очень тяжолый)...
Ручная работа практически 🤔
Exelente trabajo
I like their protective work shoes
This country has a weird thing with feet. Even when they cook their feet always had to be near the food. I don
Great job... wearing your pajamas and slippers to work. Definitely an OSHA approved working environment 🙄
La verdad es de admirar sus trabajos en la forma como lo realizan.y se ven los buenos resultados al comercio.
Fantástico! 🔥💪
C'est très intéressant. Bon courage et bon travail à vous
Show!
Muito esclarecedor e didático.
👍👍👍🇧🇷🇧🇷🇧🇷
Sul tmj
W
É quase assim, o processo produtivo está bem mais evoluído, não é necessário diversas pessoas para manipular uma chapa inteira para estampar os blancs, são usadas tiras de chapa em sistemas de estampo progressivo, como foi mostrado no vídeo é quase artesanal, hoje entra a fita de aço de um lado e sai a roda dentada do outro.
Mas lá precisa ser assim se não não vai ter emprego pra todo mundo
Да, а куда деваться людям, которые хотят трудиться, хотят работать и зарабатывать на жизнь!? Долой робототехнику, даёшь труд народа, на благо Родины и мира во всем мире!
В России вовремя СССР много заводов было
Ishlarizga omad 👍
Solo puedo sentir lastima e indignación por las condiciones de trabajo de ésta pobre gente.
Miles de dólares para el empresario, Pero para el trabajador una mierda, como en todas partes.
Nice work, little tweaking and uniforms, boots, glasses, and you will have a world class shop and the pay to go along with it. Poor guy at the end could screw the whole job with one little manual mistake to the bolt hole patterns.
Hlo
Number chahiye
Hooh
@@bhupendrakumar1235 ha
પ
молодцы, кто работает тот развивается!!! 🇷🇺✌😁
Это верно 🤗🚩
First class safety shoes at work. Love it!
Great video, thanks ! 👍
Good work keep it up. You guys r hardworking people. You shall change the destiny of your nation
Someone is making a profit, and is not investing it back in to the company and working conditions..
🤣🤣🤣👍👍👍❤❤🖤🖤❤❤🖤🚴♀️🚴♀️🚴♀️🚴♀️🏍🏍🏍🏍🏍🏍🏍🏍
Non of your business bro
@@tekittontv1 You take all these people through the processes and justify the working practices.
Tipoco y muy comun en ese pais.
@@tekittontv1 Go change your mother's diapers, you have no business here.
ما شا ءالله Good Job
Well done,good job so educating.
I wouldn't want that cheap ass sprocket on anything im riding
Excentric and/or oval sprockets made out of urinal iron.