I try for at least 3 days to figure out, you need to take out the sensor, or just unplug the 3 wire plug, reset the error cu inpa or ista. And it will work
Hy your video is just crazy, thank you very much 🙏🙏 But i have got a little question, if my problem is on the "satellite front right", is it exactly the same manipulation, just disable this one with ncs expert and dummy ?? And me too i have to unplug the module for the seat ? Thank you for all If you have an answer for me it will be so great 🙏🙏 Have a nice day Enzo
Hi sir,we did it to my e46 facelift 2004 and it work perfectly,and when we try to other e46 which is e46 pre facelift 2001 and doesn’t work,can u advice me how to do it please,thank you sir
Hi there! Not sure if you still monitor these comments, but I am attempting this various fix and need help asap! I am getting a vin faulty error even though it is entered correctly. I have a e46 bmw 330Ci with the Auto Transmission. The ecu model is the Seimens MS45.1. Please help!
You don't have to enter the VIN pretty sure (unless you aren't doing that and it is just NCS-expert being wack with its error codes). You may be able to select a different ECU under "Choose ECU". Try all of them- it may eventually work.
The pregnant man is gone! :D Best video ever. I'm going to code out my sensor on my e85 Z4 rather than fit a bypass resistor/diode mod.
Man, I've been dealing with this for over 6 months and it's finally off. Thank you !
Hello, thanks! Everything is right! But now after this operation, both airbags normally will works when car will be crashed?
thanks man ,great tutorial, the easiest one I have found so far.
Thanks guys! Works like a charm! 😉
What about E87? It’s been quite difficult to get it working getting work with, but toolset32, INPA, and ISTA ok, just that NCS…. :(
Hi,i did all the steps light goes out,but when i restart the car reapears, what i can doo?
Did you find out? Got the same issue at the moment.
I try for at least 3 days to figure out, you need to take out the sensor, or just unplug the 3 wire plug, reset the error cu inpa or ista. And it will work
Aight, gonna see if it works. Plugged the wire out. Got inpa.@@paulsele2875
@@paulsele2875 delete the code. Deleted the plug or wire. Its gone. But everytime i start the car its coming back.
What cable to plug? OBD2? Thanks
And if u choose module this gives error no matter what u choose whats next?
Hello, is it possible to reset SRS module when you had your airbag activated?
Hy your video is just crazy, thank you very much 🙏🙏
But i have got a little question, if my problem is on the "satellite front right", is it exactly the same manipulation, just disable this one with ncs expert and dummy ?? And me too i have to unplug the module for the seat ?
Thank you for all
If you have an answer for me it will be so great 🙏🙏
Have a nice day
Enzo
Paldies par video🙂
Hi sir,we did it to my e46 facelift 2004 and it work perfectly,and when we try to other e46 which is e46 pre facelift 2001 and doesn’t work,can u advice me how to do it please,thank you sir
латышок рулит йо йо LV! :)
I haven't got NCS dummy profile, which one choose?
i would like disable pdc and break sensor
Thanks man , great video!
Thanks a lot !!
thanks in advance. please tell me where I can download them~~~~!!!!!
Thank youuuu !!!!!
No have AGB in box
Ty
528i, 2011 how to clear error.
Hi there! Not sure if you still monitor these comments, but I am attempting this various fix and need help asap! I am getting a vin faulty error even though it is entered correctly. I have a e46 bmw 330Ci with the Auto Transmission. The ecu model is the Seimens MS45.1. Please help!
You don't have to enter the VIN pretty sure (unless you aren't doing that and it is just NCS-expert being wack with its error codes). You may be able to select a different ECU under "Choose ECU". Try all of them- it may eventually work.
I had this issue and it was fixed by switching the pin bridge on the cable
Great video thanks!
pregnant man xD good une
Will the airbag still work though?
Yes
PASoft is a lot easier to use.
Hi i received error when coding
It says
Error in CABD! Look at Cabi.err and error
CC AUFTRAG: ERROR_ECU_PARAMETER_WRITE
Did you solve it? I have the same error when coding out the seat belt pre tensioner. Thanks
@@matthewmicallef8287 I ended up code my airbag with PA Soft / BMW Scanner 1.4 it works perfectly
@@gtalearntodrift I’ll probably end up doing the same. Thanks for the reply :)
@@gtalearntodrift Hey there, did you had to bought a BMW Scanner cable to work with BMW Scanner or the K+DCAN cable can work with the software?
@@matthewmicallef8287hey did you end up doing this? I’m having the same exact issue with seat belt tensioner