thank you soooo much. had to leave my boat 2 hours away today because my trim wouldnt go up. i should be able to easily get it fixed when i get back tomorrow.
Hi Brandon you dont need to cut the plug you can releease the terminals with a thin screwdriver by pressing tabs in on the spade terminals it tricky but i have done it multiple times
Hi, great video. Have a question. I have a 94 Johnson 88 spl and my power trim tilt only go up but not down. I have switch the relay and replace the motor but it still have the same problem. My next step are to replace the seal. What do you think my problem is and would replace the seal fix my problem. Thanks for your help.
I am going through this now. 2004 Tahatsu 30 hp. Salt water New England motor, I got the top pin out but can barely pivot pump on lower shaft or drive shaft out. May end up sawing shaft to get apart.
Having problems with the tilt and trim unit on a Evinrude 90 hp. It will not trim going across the water. I cleaned it and resealed it. Everything works fine but it still will not trim up going across the water. Do you have any idea what could be going on? Do you know if I could get hydraulic stematic for that unit? Thanks for the videos!
I need your help. The manual trim linkage on my Johnson 40 is broken and I’m trying to fix the little plastic piece that clips on but the motor won’t go down moving the shaft
hi i have a johnson 90 from 2000 and its woring okej but now the trimpower goes up and down but stops right before the 2 trim pistones or what you call itwhy ? do you have any idea what to do
Please I have a question, I have a really nice J10R76H outer but engine needs work and a J15RCRM 84’. Can I take the power unit off and stuff it on the 9.9 shell?
Been there and mushroomed out the threads on the lower rod. Was thinking you could drill and tap for a slide hammer adapter on those older style upper pins, but is that stainless?
yes stainless. a slide hammer never thought of that, but you really couldnt get enough force to take a really stuck pin out with that. Just so long as you hit it with a pin that is not larger than the pin in the motor, you should be fine
I need that little plug you despise? In a female 5 pin ..i changed my motor and both ends are male ..the round one with the wire clip that holds it together ..what do they call that omc connector ? I tried my local dealer , but if your not buying a boat from them they arent interisted in finding parts for ya ..
K tal amigo ando buscando el CDI de motor jonshon Evinrude 4 cilindros 115 hp 2 tiempos no lo tendrás soy de Chihuahua México me podrías ayudar con eso te lo agradecería mucho
@@BrandonsGarage There are also outboard motor "junk yards" that sell used parts. Just bought a Tilt/Trim unit for my 50 HP Johnson for $400. The whole kit including switch.
thank you soooo much. had to leave my boat 2 hours away today because my trim wouldnt go up. i should be able to easily get it fixed when i get back tomorrow.
You’re a champion. Was always wondering how to remove top pin on my Evinrude etec 50 hp 2005. Thank you so much mate
Hi Brandon you dont need to cut the plug you can releease the terminals with a thin screwdriver by pressing tabs in on the spade terminals it tricky but i have done it multiple times
Hi, great video. Have a question. I have a 94 Johnson 88 spl and my power trim tilt only go up but not down. I have switch the relay and replace the motor but it still have the same problem. My next step are to replace the seal. What do you think my problem is and would replace the seal fix my problem. Thanks for your help.
1:35 what thread is it? Thanks for a very goo educational video!
I am going through this now. 2004 Tahatsu 30 hp. Salt water New England motor, I got the top pin out but can barely pivot pump on lower shaft or drive shaft out. May end up sawing shaft to get apart.
What is the thread size of the pin that holds the upper end of the tilt/trim cyl. Shaft.
Brandon, I need your expert help with rebuilding this exact tilt trim...do you have a video of this and if you can please send
Thank you!
Having problems with the tilt and trim unit on a Evinrude 90 hp. It will not trim going across the water. I cleaned it and resealed it. Everything works fine but it still will not trim up going across the water. Do you have any idea what could be going on? Do you know if I could get hydraulic stematic for that unit? Thanks for the videos!
I have a 1995 omc 70 hp 3 cly I need to put new seal kit I can not get the pin out of my tilt and trim they are frose in the brackets
I need your help. The manual trim linkage on my Johnson 40 is broken and I’m trying to fix the little plastic piece that clips on but the motor won’t go down moving the shaft
hi i have a johnson 90 from 2000 and its woring okej but now the trimpower goes up and down but stops right before the 2 trim pistones or what you call itwhy ? do you have any idea what to do
Where can I get the adapter for the slide pin? Ive been looking all over the place
Hello, where i can find the adapter you use on video to pull out the pin?
Please I have a question, I have a really nice J10R76H outer but engine needs work and a J15RCRM 84’. Can I take the power unit off and stuff it on the 9.9 shell?
I need to purchase another rod, where can I get it?
Been there and mushroomed out the threads on the lower rod. Was thinking you could drill and tap for a slide hammer adapter on those older style upper pins, but is that stainless?
yes stainless. a slide hammer never thought of that, but you really couldnt get enough force to take a really stuck pin out with that. Just so long as you hit it with a pin that is not larger than the pin in the motor, you should be fine
I need that little plug you despise? In a female 5 pin ..i changed my motor and both ends are male ..the round one with the wire clip that holds it together ..what do they call that omc connector ? I tried my local dealer , but if your not buying a boat from them they arent interisted in finding parts for ya ..
The 5 rubber pin? I hate the 2 pin plastic one.
K tal amigo ando buscando el CDI de motor jonshon Evinrude 4 cilindros 115 hp 2 tiempos no lo tendrás soy de Chihuahua México me podrías ayudar con eso te lo agradecería mucho
Have the puller and tried punches mine won’t budge I’m at a stand still
Top or bottom?
Can you convert a manual trim 40hp Johnson to electric trim or do you have to buy a whole new unit
You'll have to buy the power trim unit.
Will you sell me tilt lock lever assembly?
I have a 48 Spl i need a power trim unit for.
Check out ebay? They are on there frequently.
@@BrandonsGarage There are also outboard motor "junk yards" that sell used parts. Just bought a Tilt/Trim unit for my 50 HP Johnson for $400. The whole kit including switch.
Any outboards for sale? I think I am close to you.
Small ones currently, less than 10hp
Such a really bad engineering and design