Skipped over one of the things I really needed to see 😭. Can we talk about how freaking difficult it is to remove the plastic cover because of the wire harness clips in the back that are hooked to both the plastic cover and a bulky plastic bracket. The squeeze is so tight that even though I finally got the clips separated I STILL can’t get the plastic cover off. I’ve probably spent more time trying to remove it than it takes some to rebuild the dang engine. Haha
Good job showing the process little by little. However my GMC Sierra 1500 had 4 plastic retainers attached to the cover secured to the wire bundle behind the top cover of the manifold valve cover and against the fire wall that would not allow to be removed both together. Be aware of this.
I have a code p0300 i replaced spark plugs and wires. Had the code removed after and ran good no issue but the engine light came back on.. sometimes it blinks and stays solid. Any suggestions ??
Hello I think I'm having the same problem with my 2016 Chevrolet Silverado Lt 1500 I thought it was spark plugs or ignition coil. I replace the spark plugs. But still have the rough idle engine shaking. Also change the O2 sensors. So you think it could be the fuel injector??
I am having the same issue engine shakes bad scanner detected #5 misfires I change spark plugs coils wires and still nothing did u happen to figure out what it was ??
Авто/Мото
Ary, mi amigo...RUclips needs more guys like you. Doing a voice over on a tutorial is perfect!
Skipped over one of the things I really needed to see 😭. Can we talk about how freaking difficult it is to remove the plastic cover because of the wire harness clips in the back that are hooked to both the plastic cover and a bulky plastic bracket. The squeeze is so tight that even though I finally got the clips separated I STILL can’t get the plastic cover off. I’ve probably spent more time trying to remove it than it takes some to rebuild the dang engine. Haha
This is the only video that helped me do a step by step
Did you truck start to jerk a lot and take off when accelerating from a stop?
Thank you for sharing this video Very helpful for us silverado owners whose doing DIY maintenance.
Great job buddy! Thanks for passing along this tutorial. I love the accent 😃 ! Blessings!
Good video, thank you!
Good job showing the process little by little. However my GMC Sierra 1500 had 4 plastic retainers attached to the cover secured to the wire bundle behind the top cover of the manifold valve cover and against the fire wall that would not allow to be removed both together. Be aware of this.
Thank you señor, bendiciones
Great Video! Thank you!
Glad you liked it!
Thanks!
Gracias
Your a God send to many people my friend never stop the information you have God Bless Amigo
Muy buen video usted sabe cual es el sensor que activa y desactiva los cuatro cilindros en estas trocas ???? Gracias
Do i have to replace the fuel line feeder?
Crees que esto cause que me salga el código p219a es un air/fuel ratio bank 1 imbalance
Did you use the same fuel line feed to the injectors or bought new ones?
Nice 👍😎
Thanks for the visit
What happened to the white seal gaskets? Do they go in or not?
Did these fuel injectors last?
What was the mileage on this vehicle?
Where did you buy the fuel injectors?
How have those injectors worked out
Need to do mines diz summer lol
I have a code p0300 i replaced spark plugs and wires. Had the code removed after and ran good no issue but the engine light came back on.. sometimes it blinks and stays solid. Any suggestions ??
What symptoms does it have as long as it’s not shaking and idling bad your fine
How much will u charges to do this type of job to my truck ?
Gracias a migo aslo en español te saldria exelente gracias
i belive i have the same problem, my engine makes tick tick noise i get the code P219A in bank 1 . does anyone else is getting this problem?
the tick is probably the lifters
Hello I think I'm having the same problem with my 2016 Chevrolet Silverado Lt 1500 I thought it was spark plugs or ignition coil. I replace the spark plugs. But still have the rough idle engine shaking. Also change the O2 sensors. So you think it could be the fuel injector??
What should I do
If it's cylinder # 1,7,2 or 6 it might Be a bad lifter
I am having the same issue engine shakes bad scanner detected #5 misfires I change spark plugs coils wires and still nothing did u happen to figure out what it was ??
@@manuelj9812 my issue was an injector #6
Did it smell like gas ? Did u ever get fixed ?
I have p050D
P050d code on mine to. Code reader says to replace injectors.
You not supposed to put grease bro
Kitchen Grease is absolutely fine. Small amounts of Crisco works great.
Mejor aslo en español
Which Scanner do you use Ary? I would like to buy one but which do you use and which do you think is best?