Hopefully I’ll get this done successfully. It’s bad enough they put halogen bulbs in a 2021 car, but then they have to make it as tight as possible to reach to change the bulbs
The "lock" is on the harness itself, its similar to those clicky pens that unlock using a side button, so it you put your finger in between the lock and the body of the lamp, and push down, so its basically "out and down"
I have had the car for a month and ironically have to drive a long way to work in a rural area in the middles of the night. The halogen lights are terrible.
It’s one bulb. It’s a projector so there is a shutter that covers half of the tunnel the light comes through, then the shutter lifts up when you activate the high beam to allow more light.
Thanks I did all my interior lights from your videos. All worked great except one map light . I pushed too hard and the housing is behind the plastic. Hyundai said its a warranty thing so that works. Headlights arrive in a few days. Again thanks
Thanks for the help dude! When I got to work on changing my headlights I discovered that I had a Bigfoot hand size, so I think I am going to have to remove the bumper to do it ;( tough life man
I did it as shown in the video but it appears that one of the headlights aren't aligned properly. I don't remember if it was like that prior to installation, but I've confirmed that it's not a bulb issue since I w swapped them and the same side was still aimed lower. Is it possible to realign it myself and how would I do that?
I bought Sylvania Led headlights for my 2022 hyundai elantra, but now I am not sure if they are even street legal. Any tips or advice from those in/from Ohio would be appreciated.
Hello, thanks for nice instructions. Today, I put one side in and I have a question. When I turned on light for 10 seconds, the whole SEALIGHT Scoparc 9005 bulb(bulb, box) is extremely hot, so I was scared and hold on to put in otherside. Is this normal and safe? LED bulb + wire + black unit together in the small box with cap would not cool down heat from LED.
I literally just tried to do this on my 23 preferred Elantra and just couldn’t do it. I’ve got somewhat big hands so it’s almost impossible to do that driver side for me. Any tips?
@@RevTheoryWPG I got some good scratches on my wrist at the drivers side, but my hand could fit all the way down there, I think the best to do is to get someone with smaller hands to help 🥲
@@FernandoGranco i managed to get the LED bulb in, but because of how tight the area is I could t for the life of me twist it into place. I think I’m just gonna take the front wheels off and the wheel liners. I’ve seen lots of people doing it that way
@@RevTheoryWPG This side is awful, check to make sure you are putting it with the tabs on the right place, check the ones you took out to see the right way. I had more trouble twisting out the one that came with the car than the new one 😄
@@ClubAmerica92 Very good. Just followed the video. Order parts from Amazon. Just be patient when replacing. Note, recommend adjusting lens angle after doing it. Good luck.
Great tutorial! The drl on one side of my elantra are out. It's not the actual bulb you replaced in this video. It's the drl above that. I can't find the bulb to replace the drl! Do I need to replace the entire headlight for the drl to work again? Please help! Thank you!
So these led replacements dont through up error codes or anything like that? Also, do i need to position them a certain way so other drivers are not blinded, or does the projector headlight housing make it not matter?
Thanks for tutorial, I was able to get the 2nd bulb to twist easier. Waiting for nighttime to check them out. && What did you do with the little rectangular piece attached to bulb, is it ok for it to just dangle in there or did you zip tie it to something. Maybe some double sided 3m tape would do?
Hey, any tips on why I'm getting condensation inside both the headlights even though the dust caps are pretty tightly fit? I got the same bulbs in Toronto, and while they work really well, they won't seal.. Your help would be amazing..
@@taichiherov8135 I reinstalled the bulbs, properly installing them in place the 2nd time. It's been 2 years, and there's no condensation anymore. I think there was a slight gap before, that I was able to get sealed up. Didn't need any silica bags.
Is there only one way for the bulb to sit in the housing? I have a feeling when I put them in, I forgot to lock them in place? Because the are king of pointing down and not straight. I just want to mention that I tried without removing the bumper, just with my hands and it’s pretty hard to see inside the housing that way…Did you have to twist them in after they were in the hole?
Dan, when you put the LED light as shown, did it go into the desired 3 & 9 o’clock position without having to play with it, and looking at it from the front?
Oh gosh I just did this and it was awful. I used to work on cell sites and everything on the top of a tower is extremely compact so I was very good with my hands in super small spaces but this one killed me. Glad it’s done. (2023 Elantra SEL here)
Hi there, I’m having some serious trouble putting in one of the bulbs. The bulb on one side went in smoothly and was tight, but the other bulb is simply not getting set in place. It remains loose when I push it all the way in, and doesn’t respond to clockwise twisting. Could this be an issue with the bulb? It didn’t look any different than the first one I put in.
Its prob from fans of the leds. Leds usually come with mini fans attached to help cool them down while on. Since led is working harder since high beams are on it requires more energy in turn, it heats up faster so fans move faster to dissipate the heat so thats prob the noise u hear
Mine does the same thing noticed after I changed. Did you go to the mechanic to check everything okey, or that is just normal sound when you change to high beams ?
Hey bro can you humbly also do the led tail/trunk lights? You’d get a shit ton of views I’ve seen so many people requesting that vid on other peoples channels and reddit etc.
So I just got a 2022 SEL 3 days ago, tint done today too. Does anyone flash their brights at ya when the low beams are on? Just ordered some today. I'm over halogens. Didn't splurge on the Limited like my other half. 😂
Very SOLID Install! I've seen numerous others take off the entire bumper and housings just to do it. You did it flawlessly! Nice work 👍
pure talent here to record with one hand and use the other to do the work
Awesome vid man. I was hoping that wouldn't have to remove the bumper. Thanks again. Going to do mines soon.
Hi ! I see you installed this led headlights bulbs 1 year ago ! Can you tell me if they are still working or already replaced! Thank you
Just did it couple of minutes ago. Thanks for the help brother 🔥
Hopefully I’ll get this done successfully. It’s bad enough they put halogen bulbs in a 2021 car, but then they have to make it as tight as possible to reach to change the bulbs
I’m struggling to actually disconnect the wiring harness. When you say push forward then pull down how exactly do you mean?
The "lock" is on the harness itself, its similar to those clicky pens that unlock using a side button, so it you put your finger in between the lock and the body of the lamp, and push down, so its basically "out and down"
Is it one bulb which includes the highbeam? or two separate bulbs. The yellow bulbs are awful at night... my only complaint.
I have had the car for a month and ironically have to drive a long way to work in a rural area in the middles of the night. The halogen lights are terrible.
It’s one bulb. It’s a projector so there is a shutter that covers half of the tunnel the light comes through, then the shutter lifts up when you activate the high beam to allow more light.
Great detailed explanation of what to feel for! I got it from this video
Hello from New Brunswick. I have the same car same trim. Loving the manual transmission. Thinking of doing this same upgrade.
Thanks I did all my interior lights from your videos. All worked great except one map light . I pushed too hard and the housing is behind the plastic. Hyundai said its a warranty thing so that works. Headlights arrive in a few days. Again thanks
Thanks for the help dude! When I got to work on changing my headlights I discovered that I had a Bigfoot hand size, so I think I am going to have to remove the bumper to do it ;( tough life man
I did it as shown in the video but it appears that one of the headlights aren't aligned properly. I don't remember if it was like that prior to installation, but I've confirmed that it's not a bulb issue since I w swapped them and the same side was still aimed lower. Is it possible to realign it myself and how would I do that?
There is a grey "thingy" right next to the where the light goes, you can use a philips screwhead to change align
I bought Sylvania Led headlights for my 2022 hyundai elantra, but now I am not sure if they are even street legal. Any tips or advice from those in/from Ohio would be appreciated.
Pls , put a link with the bulbs model . I tried to find on Amazon but I didn’t find this model bulbs . Thanks !
Hello, thanks for nice instructions. Today, I put one side in and I have a question. When I turned on light for 10 seconds, the whole SEALIGHT Scoparc 9005 bulb(bulb, box) is extremely hot, so I was scared and hold on to put in otherside. Is this normal and safe? LED bulb + wire + black unit together in the small box with cap would not cool down heat from LED.
Thanks, just installed on the Elantra 2023 Prefered, it was exactly like the tutorial. How are the lights after one year?
I literally just tried to do this on my 23 preferred Elantra and just couldn’t do it. I’ve got somewhat big hands so it’s almost impossible to do that driver side for me. Any tips?
@@RevTheoryWPG I got some good scratches on my wrist at the drivers side, but my hand could fit all the way down there, I think the best to do is to get someone with smaller hands to help 🥲
@@FernandoGranco i managed to get the LED bulb in, but because of how tight the area is I could t for the life of me twist it into place. I think I’m just gonna take the front wheels off and the wheel liners. I’ve seen lots of people doing it that way
@@RevTheoryWPG This side is awful, check to make sure you are putting it with the tabs on the right place, check the ones you took out to see the right way. I had more trouble twisting out the one that came with the car than the new one 😄
Thank you so much for doing the video. Very helpful and plan to do the swap later today.
How did the swap go? Any suggestions?
@@ClubAmerica92
Very good. Just followed the video. Order parts from Amazon. Just be patient when replacing. Note, recommend adjusting lens angle after doing it. Good luck.
Great tutorial! The drl on one side of my elantra are out. It's not the actual bulb you replaced in this video. It's the drl above that. I can't find the bulb to replace the drl! Do I need to replace the entire headlight for the drl to work again? Please help! Thank you!
Warranty should cover that.
Go through the wheel well is the easiest way
I wanted to know that if i change the headlight bulbs than my warranty will be voidable or not ?
Are these led headlights compatible with the 2021 Hyundai Elantra N Line and do these led lights cause any issues within the cars computer system.
The guy does not reply
what did you do to the headlights check signal ⚠️? Because I got this signal on the screen and it's annoying.
Thank you for your video!! Seriously, THANK YOU!! 😊
Did you have "check headlight" warning after installing these?
Do you get any "Check headlight" code when you installed them?
Thanks for this video bro It helped a lot!
So these led replacements dont through up error codes or anything like that? Also, do i need to position them a certain way so other drivers are not blinded, or does the projector headlight housing make it not matter?
Do you know if these lights are dot approved?
Thanks for tutorial, I was able to get the 2nd bulb to twist easier. Waiting for nighttime to check them out. && What did you do with the little rectangular piece attached to bulb, is it ok for it to just dangle in there or did you zip tie it to something. Maybe some double sided 3m tape would do?
do you have issues where the high beam barely light up the road but the tip of the trees instead? - tried to adjust the height, but no luck so far
Hey, any tips on why I'm getting condensation inside both the headlights even though the dust caps are pretty tightly fit? I got the same bulbs in Toronto, and while they work really well, they won't seal.. Your help would be amazing..
Replace the Silica Bag in the cap. It worked for me.
But condensation still builds up even after doing this
@@taichiherov8135 I reinstalled the bulbs, properly installing them in place the 2nd time. It's been 2 years, and there's no condensation anymore. I think there was a slight gap before, that I was able to get sealed up. Didn't need any silica bags.
Bro my car same model no working the display , not turn on ,I check the fuse everything looking goods ,you have any details for this problem
just got a 2023 SEL elantra do you actually have to buy the whole compartment or just the bulb ?
Bulb
Hey my front signal light blew . What kind of bulb does 2021 Elantra take
Dude, you don't wear the gloves for disassembly. The glove is for handling the new bulb itself.
i’m confused what i’m supposed to do after i unscrew the cover? like what am i grabbing on to to pull the old light out
Bro i bought the same ones and on the street they seem hella dim are yours like that?
If you can’t take them off just take the whole bumper off made everything so much easier for me
My left headlight looks odd and is giving me an error code at times. Any tips?
Is there only one way for the bulb to sit in the housing? I have a feeling when I put them in, I forgot to lock them in place? Because the are king of pointing down and not straight. I just want to mention that I tried without removing the bumper, just with my hands and it’s pretty hard to see inside the housing that way…Did you have to twist them in after they were in the hole?
You have to twist them in place, its a very small twist
My hands can't fit where yours do unfortunately.. Can I not just remove the headlight to change out the headlight bulb?
I've seen others turn the wheel completely and access the headlight compartment from underneath the fender.
Going through the wheel well is the easiest
I bought 2022 elantra hybrid is it same bulb type(9005/HB3) used?
Last step.. mine does not click . Yes I have the right bulb and same car . I don’t hear the click
Dan, when you put the LED light as shown, did it go into the desired 3 & 9 o’clock position without having to play with it, and looking at it from the front?
It only fits this way, so you don't need to check it
Will these lights fit 2023 Elantra Hybrid Blue?
Is this for both the high and low beam?
Yes
so instead of a nasty yellow it’s a bright white? I need
was wondering if anyone knows why my left side daytime running lights won't turn on?
Do the lights have to be adjusted ?
Oh gosh I just did this and it was awful. I used to work on cell sites and everything on the top of a tower is extremely compact so I was very good with my hands in super small spaces but this one killed me. Glad it’s done. (2023 Elantra SEL here)
Hey man, I’m trying to twist out the original bulb but it will not twist out for me, am I doing something wrong?
@@jamespan8027 It’s not a full screw out or anything, just a quarter turn if that. I honestly just fiddled with mine for 30 mins or so.
Hey is their any error messages on your dash or no? Im making sure these work on my 2023 Elantra SEL
@@GamingNarwhal It works on the 2023, no error code
@@FernandoGranco what about an N-Line?
Now I imagine this would work for my ‘22, but Amazon says these do not fit.
That’s what I’m trying to figure out, I have the 22 also
Have you guys figured this out yet? XD
It works, I just installed them on my '22 SEL
@@grahambradshaw6590 have they thrown any codes or “check headlights”? I have a 22 as well
@@grahambradshaw6590 yeah how is it now that it’s been 1 month? Also do you know the name of the bulb??
Hi there, I’m having some serious trouble putting in one of the bulbs. The bulb on one side went in smoothly and was tight, but the other bulb is simply not getting set in place. It remains loose when I push it all the way in, and doesn’t respond to clockwise twisting. Could this be an issue with the bulb? It didn’t look any different than the first one I put in.
I’m having the same issue
Check out Precision LED for an in interior package for your car . I’ve used them since 2016 . 2016 Elantra GT. Good video 👍🇨🇦
Is this the same for 2022 Elantra or did the bulbs change? Can't find much on Google.
The same for the 2022 and 2023
i put my car and now just coming check headlights now how to i fixed
I wanna do this to mine but it looks so f difficult
its fit on ioniq ?
how do you disconnect the wiring harness what do you mean by push forward and pull?
Push down on the tab on back of the light and pull out
Did you install the led headlight for high beams as well?
One bulb does both . . .
Pls show us tue product next time,nerded to see if it needed an anti flicker device which most ppl say it is not necessary
is it hi/low function the one you replaced ?
Yed
Does the stock bulb have one or two filaments?
One, but its the low and high in the same bulb
Hey bro i just followed what you did they fit turn on but the lights are so weak :(
For the Elantra too!??
I just changed mine out but it’s day time right now so idk how well they work… I hope it’s worth it 😩😩 I spent so much time on this
It doesn't work for my 2022 Elantra SE
Muchas gracias lo pude lograr te agradezco muchísimo
Hi! Can you PLEASE give a link for which lights you used for this upgrade.
it’s in the description :)
Hey is it possible to show where the leveler is ? I have a dead spot after I installed my LEDs
It's a gray circular funnel. Can't miss it.
@@WilldaBear BRUH it was in my face the whole time 🤣 thanks man i’ll try that tonight
@@mc-ri2zp No problem, I had the same issue.
i keep getting check headlight warning
What year what leds u use
Idk if it was there before but when I change from low beams to high beams it makes a noise…. Is that normal???
Mine does the same thing noticed after but couldn’t remember from before
Its prob from fans of the leds. Leds usually come with mini fans attached to help cool them down while on. Since led is working harder since high beams are on it requires more energy in turn, it heats up faster so fans move faster to dissipate the heat so thats prob the noise u hear
@@jamesmoon3345 ahh okay yeah could simply be how it is. My leds make noise & they come factory from hyundai . I have a sonata n line
Mine does the same thing noticed after I changed. Did you go to the mechanic to check everything okey, or that is just normal sound when you change to high beams ?
Hey bro can you humbly also do the led tail/trunk lights? You’d get a shit ton of views I’ve seen so many people requesting that vid on other peoples channels and reddit etc.
I have a bunch of led’s on order should be here in a few days upgrading everything
You must have the tiniest hands in the world.
Show the passenger side smart guy
5:01 no pun intended
From where did you order the led lights?
He said Amazon
So I just got a 2022 SEL 3 days ago, tint done today too. Does anyone flash their brights at ya when the low beams are on? Just ordered some today. I'm over halogens. Didn't splurge on the Limited like my other half. 😂
Funny because my other half got the limited in black and I got the SEL in red. How did changing the bulbs go for you
FFS, nice going Hyundai, we dont all have tiny Korean hands 🤬
👍 süper
Links for the bulbs?
SEALIGHT Scoparc 9005/HB3 LED Headlights Bulb, High Beam LED Bulb, 9145/H10 Fog Light Bulbs, 6000K Bright White, Halogen Replacement, Quick Installation www.amazon.ca/dp/B079KB8J98/ref=cm_sw_r_cp_api_glt_i_2P6GTTX767KWY1VBN8AH?_encoding=UTF8&psc=1
@@DANNYGZK this is for low beam? How about high beam
@@kyawlinhtoo low and high in same bulb
Any plans on upgrading the turn signals??
@@DANNYGZK when I follow the link to Amazon, it says it does not fit my 2021 Elantra?
Does the auto headlight feature still work when switching to LED lights?
It will yes.