The fun fact is this is will follow the line only you can not control it with your device because you are not using Node MCU or Arduino module. Though it is easy. No need to program it. Btw nice project at very low cost. Thanks for the video.
Approximately ₹700 2 IR sensor ₹80 2 Dc motors ₹100 L298n drive ₹140 2 Wheels ₹ 40 Jumpers wires ₹50 9v battery ₹20 or li-ion battery ₹250 (recommend) Chassis ₹90 or you can take Cardboard sheet Caster wheel ₹15
Hi 1 question i went to buy the motors online but non of them have the yellow and green qores attached to them so could you please explain what wires are these pls reply soon thank you 😊
Bro i make wiring according to your given circuit but in my case i use 4 motor and l298 motor driver and 2 ir sensor but the problem is in my case ir stop wheels when any object is near by and if we remove object then the motor start working 😅😅😅😅
I connected everything correctly, lastly I connected a 9v battery. The red light in motor driver and green light in sensors are glowing. But the wheels are not rotating. I need to submit this tomorrow. Please reply
@@skynet-robotics i don't know how to do it... I'm turning the screw in the sensor. I found out I need to adjust the sensor in right way.but I don't know how to do it
Mere do ir sensors hi red light jal raha hai. Tumhara tarha ak green ak red nahi jal raha. And do red jal raha isi liye kam bhi nahi kar raha please help 🙏
This is working correctly without any errors. Thanks for this video.🎉
👍✌
please the code
If there is no Arduino so why you need to upload the codes@@mimoumin8800
Thanks bro
@@mimoumin8800 which😂😂
Thanks.. I'll try to replicate this project for my class..
Very good project,
Make one video using same motordriver with arduino nano
Ok definitely
Thank you for this video it's very useful for me
Glad to hear that
sir, i do same connection like u, but motor run automatic, when i use my hand stop, but i need opposit of this work
can u help me
same thing happened for me
first of all a very good tutorial. also one thing " cant we move the ir sensors out of the line and make it follow it.
Yes but for that you hv to use Arduino
You can use NOT gate to the input from IR sensors also
Do we have to calibrate the ir sensor
Loves your projects without Arduino. Very good for students who are not ready for Arduino yet.
Thanx for appreciation🙏🙏
It motivates me to deliver projects with less resources
The fun fact is this is will follow the line only you can not control it with your device because you are not using Node MCU or Arduino module. Though it is easy. No need to program it. Btw nice project at very low cost. Thanks for the video.
Thanks for sharing
Do we have to calibrate the ir sensor
Bro Thanks its good for my project
Bro can we add another batteries
How volts does it needs
Pls rply bro
yes you can add 9V batteries
Do we have to calibrate the ir sensor
my battery holder's wire gets burnt everytime i connect it , its non functional please help
Can i add 9v battery
You can use a buck converter to lower the voltage | yes!
If we straight the ir sensor than we can make a human following robot
very nice video does it actually works without arduino?
bro need quick reply for comments
Yes it works
Busy in making another line follower
NEED MORE PROJECT LIKE THESE FOR MY CODING AND ROBOTICS PROJECT
Yes I am working on new project will published soon
Sir what is the ampere rate of the battery? please reply, due tomorrow
thank you so much..may i know what is the cost of all the components that are used
Approximately ₹700
2 IR sensor ₹80
2 Dc motors ₹100
L298n drive ₹140
2 Wheels ₹ 40
Jumpers wires ₹50
9v battery ₹20
or li-ion battery ₹250 (recommend)
Chassis ₹90 or you can take Cardboard sheet
Caster wheel ₹15
@@skynet-robotics .
Par battery ko charge karne ke liye tp406 module ko wire attach kar liya aur battery ke + Aur -ke wire ko tape stick kiya to chalega kya😅
Its speed is very fast, please tell me some way to slow it down. Please bro...
Use 100rpm motor
Or any speed controller
Can we use single gear motor....
Can I use 100 rpm bo motor
Yes 👍
@@skynet-robotics thank you 😊
Hi 1 question i went to buy the motors online but non of them have the yellow and green qores attached to them so could you please explain what wires are these pls reply soon thank you 😊
Motor not come with wires
You have to solder wires to newly purchased motor.
You can use any wire
@@skynet-robotics ok thank you
Bhai can i use 4 wheels
Please say fast because after 2 days my science fair is there in school
why we need to connect the IR1 and IR2 out pin to IN1 and IN3
To give singnal
Bro pls reply how to calibrate the sensor
Rotate potentiometer
Bhai agar battery ke wire ko button ke attached kiya to chalega kya aur fir us wire ko gnd ke sath connect kiya to chalega kya
@@saksham10k yes
Can u please tell me after all connections two wheels can move in same direction or opposite direction
It should move same direction (forward)
If not then make it forward by swaping that motor wire in terminal of driver
Bro i make wiring according to your given circuit but in my case i use 4 motor and l298 motor driver and 2 ir sensor but the problem is in my case ir stop wheels when any object is near by and if we remove object then the motor start working 😅😅😅😅
Yes it's correct
Draw black broad line
It doesn't need coding? And what is the cost of making
800
I connected everything correctly, lastly I connected a 9v battery. The red light in motor driver and green light in sensors are glowing. But the wheels are not rotating. I need to submit this tomorrow. Please reply
Hv u done sensor calibration
@@skynet-robotics i don't know how to do it... I'm turning the screw in the sensor. I found out I need to adjust the sensor in right way.but I don't know how to do it
@@kmadan7248 send video on +919075800409
Do we have to calibrate the ir sensor
Bro car moving in straight line Bro and it can't stop when is comes from the black line please give me a solution
Adjust the sensitivity
How
@@Lovebeats0116blue color potentiometer on IR sensor. Use screwdriver rotate it
Ok bro
@@Lovebeats0116 worked???
Can it work with 3.7 battery?
Oh so this one doesn't need a code? Only the ones with Arduino need codes?
What are they coding on? Is it a software we need to download before hand?
Arduino IDE
Can't we use black cardboard instead of using black tape
Sir my one is not working?
I did the circuit diagram but the l298n and the sensors doesn't light up
Need quick reply sir because I am doing a school project
You can
but it should be perfectly black
Can we use 9 volt battery?
Yes you can use 9v battery but it's backup will be very less 10-20minutes
Mere do ir sensors hi red light jal raha hai. Tumhara tarha ak green ak red nahi jal raha. And do red jal raha isi liye kam bhi nahi kar raha please help 🙏
Great one❤
Thnx
Hello, is it working. I am asking because i am going to find thing to make it.
Sir I want to ask yo a question Is it following black line or white surface
Yes
Which volt battery I use l alredy use 9v battery but is dose't move
7.4 liion
Sir can i connect more 2 dc motor to it how much volt should I give
Yes you can
7.2 to 12 volt
sir how huch volt can i give
@@skynet-robotics thanku sir
Meri gadi gol nhi ghum rhi hai kya kru please jaldi bataiye
How many colour used same like 5v
Not understood u r question
Please tell me in details
9v battery is not enough to provide the needed power
It's depends which company battery you r using.
Duracell recommend
It's depends which company battery you r using.
Duracell recommend
wow amazing
Thnx
Bhai mera robot uthaya to chalta hai aur niche rakha to nahi chalta
Agar 9v ki battery lagai to chalega kya
Chalega
Mine is one side is working and one is not working but i checked th sensivity of ir sensor pls reply thus is my school project
Send video on whatsaapp 9075800409
Bhai ek lithium battery se chalega kya
Driver need 6v
circuit done, arduino code uploaded, now how to sense the sensors???? please reply...urgent
I am not used Arduino in this project
Mine goes too fast and goes out of line during a bend.. can i reduce the speed without Arduino controller?
Use 100rpm motor
Or use only two batteries
Does 9v battery work for these doesn't it need 12v??
Yes it will work but 9V battery backup very less
sir can i give power from ac to dc 12v adopter
Yes
Will work fine with 12v
All connections are same but not following black line sirf gol gumrahi hai so plss tell what can i do 😢😢😢😢
Plss
I am doing this
Sensor calibration Karo potentiometer ghumake
Please tell the name and volt of the battery You used
Li-ion 18650 3.7 Volt
2 batteries (3.7+3.7= 7.2V)
Very nice idea
Thnx
BRO PLZ REPLAY TOMORROW LASTDAY😢😢
I ACCIDENTALLY BUY L293N MOTOR CONTROLLER CAN I USE IT🙏
Yes
how much volt battery needed? 3.7v???
6-12
@@skynet-robotics i have bough 2 lithium ion battery which is 3.7v each
If the sensor is on and the driver is too but it won't work, what's the cause?
Send video on Instagram
@@skynet-robotics I've done it bro
sir how much weight it can carry
3kg if you are using plastic gear motor
10kg if you are using metal Gear big motor
When i connect 5v With Input 2 motor not working (Testing Condition)
Make sure you are providing 5v
I am using 9 volt Battery for power supply
@@TheNoobVishuwhatsApp connection on 9405276005
Coding nahi karani padati hai kya 😮
Thax bro i have made it
👍❤
Super dear keep it up
Thnx
How many students can do this
2
Is it work in sunlight? And can I use one lithium battery?
Yes it will work in sunlight.
You have to use two Li-ion batteries because one Li-ion battery not gives sufficient voltage to motor driver
it wont works in sulight
Wow
There is some doubt in this project bro you will solve it my doubt?
Yes, tell me
I have a robot but it just vibrate it doesnt go forward why ?
Battery voltage?
Hey i have also tried same model ,my sensors are working but my model is not following line i have used 9v battery
Pls reply what should I do?
Adjust sensitivity of sensor
Do we have to calibrate the ir sensor
can we make it follow a white line instead of black?
if so then how?
For that you have to use Arduino
In the coding you have to make adjustment
Don't worry I will bring next video on white line follower
Good
Thnx
One motor is not rotating the other one is help me reply pls is urgent
Send screenshot on Instagram @skynetrobotics
Thanku bro
Welcome
Is it going ro work only with one sensor?
Both direction with Both sensor
What is the use of line follower
Industry
Where can we buy these parts
Is it available online
Yes
Bro will it work in fast line following Robot n20 motors (600rpm)
Which sensor u r going to use
I tried it but Motor speed is very high can't control it. I used 2 lithium iron battery what can I do
Use 150rpm motors
@@skynet-robotics there is any other ways?
Can we use timer 555?
Yes but what is your project theme
How many volt in DC motor sir?
Use 150 rpm BO gear motor
Volt 5-12
@@skynet-robotics thanks bro
Weele is not working in cap wire
Insert cap at EnA and EnB pins
My robot too fast moving forward, can't following the line
plz help me sir
Use motor with low RPM
It working bro tq
Make another black line and do it
Not getting your point
Bro this project using one sensor car is run or not sir?
You need two
All wiring or current but the will dose't move😢😢
Insert jumpers to EnA and EnB pin
@@skynet-robotics what is this sir . This car project will wort or not .
Mau nanya tanda out put nya itu A0 apa d0?
Not understood
Explain in detail
Not working bro 😐
What problem u facing
It round moving
Bhaiya mere gadi ka ek wheel clockwise aur dusra anticlockwise ghum rha hai kya kru please jaldi bataiye
Jo motor reverse ghum raha hain uske wire ulte kardo
@@skynet-robotics ok
Sir how much will this cost?
850
Without Arduino how is it possible to follow only one line even on turns
It's possible you can try
@@skynet-robotics Without processor how can we control it !
Fake 😂
@@siumbinamin9695 really??
Real l have made it before
Bhai properly work toh karega na kyunki bina Arduino ke hai yeh
Yes of course
that's why video ka title diya hain.
Go for it
If I give 7.2 volt ,will the ir sensor burn.Can i use power bank as battery
Don't worry you can give voltage between 6 to 12 V to drive then drive covert 5v for IR sensor
Just follow connection diagram
It’s not work only one wheel move
Can you please help
Adjust the sensitivity of sensors.
It will work fine.
If not then send me video of project on 9405276005(whatsapp)
But is this following white or black
Black
Bro only one tyre is working
Adjust sensor sensitivity
@@skynet-robotics nhi ho rha h bro
The well is not rotate😢😢
What is +/- in motor
No
Motor does not follow +/- Polarity
It simply change directions according to battery terminal
EnA and EnB jumpers chk
Why my project didnt work?
Insert enA and EnB jumpers
How to increase speed
Use 12v battery
Thanks
@@skynet-robotics
Is that needs a code and if were we have to put that code😢
No need for this
@@skynet-robotics thanks for very fast reply
My robot is not following the line
Adjust the sensitivity of sensor