0:00 - Intro 1:32 - How to go into programming mode 3:17 - How to program/add points in the SLC 7:02 - Point programming 12:10 - Notifier special function programming 13:27 - How to program NAC sync/coding options 17:14 - Setting up an agent release NAC 19:21 - How to change notifier LED polling speed 21:12 - How to change the system normal message 22:38 - How to turn off trouble reminder 23:30 - How to change addressable protocols 24:04 - Testing the panel and alarms
@Roxxofoxxo Hey I have this same system but I’m having an issue when my main sprinkler valve is closed I get a trouble but when the valve is close the supervisory light should turn on but it’s not any input would be appreciated thank you.
I'm assuming you know the monitor module address that is connected to the tamper value. You're using the wrong point type for that device, go into programming mode and change the point type from a trouble to a tamper point type
I cant seems to get to the " change program " menu, even im using the correct password. It just gets back to the home screen. Sometimes it works but most of the time not. 1:32 . I know that its not a wrong password since it doesnt shows error it just simply puts me back to home screen.
You have to use the FSP-951IV if not the it won’t accept the new device. New FSP-951 are flash scan protocol the since you were working on an older system which is set up for clip mode protocol, you would have to use a FSP-951IV which is set for both Flash Scan & Clip Mode Protocol.
I have a smoke detector that failed to recall the elevator. So the recall relay isn’t assigned with the smoke. Is it possible to change that through the panel ?
I try modifying a detector and it wouldn’t let me. For example I tried modifying a detector the address was 1D001 but instead it took me to the 2 detector which is 1D002 I tried, and tried changing ID001 but it just skips to 1D002. Do I have to run auto program again to modify this point????
Do you have a template of the word meanings like AHJ codes like that and what they are used for… and please don’t abuse ur panel at 14:48 I almost dropped my dinner 🤣🤣
0:00 - Intro
1:32 - How to go into programming mode
3:17 - How to program/add points in the SLC
7:02 - Point programming
12:10 - Notifier special function programming
13:27 - How to program NAC sync/coding options
17:14 - Setting up an agent release NAC
19:21 - How to change notifier LED polling speed
21:12 - How to change the system normal message
22:38 - How to turn off trouble reminder
23:30 - How to change addressable protocols
24:04 - Testing the panel and alarms
@Roxxofoxxo Hey I have this same system but I’m having an issue when my main sprinkler valve is closed I get a trouble but when the valve is close the supervisory light should turn on but it’s not any input would be appreciated thank you.
I'm assuming you know the monitor module address that is connected to the tamper value. You're using the wrong point type for that device, go into programming mode and change the point type from a trouble to a tamper point type
@@Roxxofoxxo I do have the address I will look at it tomorrow thank you again.
Excelente demostración. Felicidades!
there is some reason we need to shutdown this control box. how do we do it? and how to turn it on again when we want to use it ?
But, what if i don't have the password
I cant seems to get to the " change program " menu, even im using the correct password. It just gets back to the home screen. Sometimes it works but most of the time not. 1:32 .
I know that its not a wrong password since it doesnt shows error it just simply puts me back to home screen.
theres Security LED and try connect home security with panel
I have a remote annunciator, and i do not know how to program it, could you help me with that
Is there a default passwork to access Basic Programming?
y el admin password is 00000
How to Change Date and Time
We replaced an existing FSP-851 with the newer FSP-951 detector and base. But the panel showed trouble TEST F. What could be the problem...?
You have to use the FSP-951IV if not the it won’t accept the new device. New FSP-951 are flash scan protocol the since you were working on an older system which is set up for clip mode protocol, you would have to use a FSP-951IV which is set for both Flash Scan & Clip Mode Protocol.
@@EZBANK4L_ Thanks. That's exactly what we had to do to resolve this issue...
I have a smoke detector that failed to recall the elevator. So the recall relay isn’t assigned with the smoke. Is it possible to change that through the panel ?
Yes, you’ll need the master password. Go into programming and edit the device, you’ll need to add the zone for recall to that detector.
is there any way to remove this beep from the fault ?
Press the acknowledge button
yes I will totally need this for totally legit fire alarm stuff hmmm yes
If cross zones activate, will it cause a pre discharge countdown? Thanks!
Yes, I am pretty sure
@@Roxxofoxxo Cool! Thanks!
@@calebmorand4604 np
nfs 320 next plz
I need you help..
does the 640 use both the 320 and 2-3030 cpu cause ive seen some with the 3030 cpu and the 320 cpu like this one
It used a cpu similar to the 320, that is basically identical besides some hardware and firmware differences
@@Roxxofoxxooh
How to activate the smoke detector remotely, through the control panel ?
no can do, but if you want to make the sirens to go, keep pushing drill botton for 2 seconds
I try modifying a detector and it wouldn’t let me. For example I tried modifying a detector the address was 1D001 but instead it took me to the 2 detector which is 1D002 I tried, and tried changing ID001 but it just skips to 1D002. Do I have to run auto program again to modify this point????
What are you trying to modify detector 1 as, or are you trying to add detector 1 to the panel?
@@Roxxofoxxo I wanted to label it 1D001 - Admin Board room, and it’s zone but it just skips to 1D002 which I already labelled as Admin Sales
to add a new device you need to autoprogram, to erase other you doit in modify point.@@legrandscanlan6336
¿como habilitar software de una nfs2 640 bloqueada?
When i press auto programming nothing is happening what to do?
Do you have devices connected to your SLC?
Can you autoprogram a new device if you already have existing programmed detectors or modules on the slc?
Yes
Just use autoprogram
@@Roxxofoxxo awesome! Thanks.
Np!
@@calebmorand4604 you plan on getting a Notifier onyx?
@@Roxxofoxxo yes I do. They seem very nice. Probably a 320 or 640. Do both program the same?
Can you tell me,how to use CBE
Set the module to the zone you wish to control
Then a output module or a nac to said zone
Do you have a template of the word meanings like AHJ codes like that and what they are used for… and please don’t abuse ur panel at 14:48 I almost dropped my dinner 🤣🤣
I do not.
Notifier simp 😤
Yesssirrr
Tea you are terrible