The tiles at the bottom left & right corners are high as they go into the reveal. (at 3:31 mins) It looks quite bad where they aren't level with the trim.
Thanks for this. I had not been sure if it was OK to put the adhesive on the tiles as I was taught many years ago to put adhesive on an area of wall. The problem with that is you might do too big an area and have to remove excess at the end.
I use my eye to level the tiles , saves on spirit levels, battens, spacers and screws. Easy money in my pocket. FYI I'm not very busy with work if anyone needs a hand.
That rare occasion when you say who the bloody hell gave this 29 up votes! Start at the top...then only tile half way up...oh, the list is endless...worst vid ever!!!!
this is actually poor tiling, no levelling tools, edges are scrappy, the way he applies adhesive was dreadful! the whole back of the tile should have a full layer
Why not have 3 full tiles rather than have to cut all the bottom row. So what if the tiles would be a couple inches higher up the wall. Weird. Also no explanation of the window sil trim. You seem to have left the sil tiles short of the trim? This would then need to be filled with grout. Not a nice look. Trim is so you don't have grout along those corners/bends.
wow! there are alot of amateur things going on here, quite embarrassing tbh. first off, it looks like you layout from left to right is centered incorrectly, yes the window is centered, but if you had moved the complete right to left layout over one half tile, you would of had big centered cuts everywhere instead of those smaller cuts. also tiling the sill should be done before the sides, not after. you never shimmed the schluters to be completed even with the tiles edge. you should always apply adhesive to walls also, not just tile. you also didn't use enough adhesive when you were tiling the bottom section, you can clearly see the wall boards in between the trowel notches. and what's with starting on that board? that's just a waste of time because you now have to shimm from that board and then shimm again at base, if you just start at bottom, your just shimming once and you don't have to spend the time screwing and leveling that board. just make a level line up from base 1 or 2 tiles and shim to it, then keep going up. lots of mistakes imo
incorrect. Around windows tikes needs to be angled, otherwise water will stand. No need to use any profiles for hiding, cut tiles in an angle... like 45 degree
wow! there are alot of amateur things going on here, quite embarrassing tbh. first off, it looks like your layout from left to right is centered incorrectly, yes the window is centered, but if you had moved the complete right to left layout over one half tile, you would of had big centered cuts everywhere instead of those smaller cuts. also tiling the sill should be done before the sides, not after. you never shimmed the schluters to be completely even with the tiles edge. you should always apply adhesive to walls also, not just tile. you also didn't use enough adhesive when you were tiling the bottom section, you can clearly see the wall boards in between the trowel notches. and what's with starting on that board? that's just a waste of time because you now have to shimm from that board and then shimm again at base, if you just start at bottom, your just shimming once and you don't have to spend the time screwing and leveling that board. just make a level line up from base 1 or 2 tiles and shim to it, then keep going up. lots of mistakes imo
vapdivrr you posted the same comment twice?are you a tile setter by trade? If so maybe you should post some videos so others can critique your work. I'm not saying this guy did a good job and your right about everything you said.im just saying.
Well, i'm assuming that batten he used wasn't from B and Q, or it wouldn't of even been straight...
The tiles at the bottom left & right corners are high as they go into the reveal. (at 3:31 mins) It looks quite bad where they aren't level with the trim.
I noticed that too David!! That would irritate me, I'd have had him correct it before giving him his cuppa.
It's a poor tiling job and a poor instructional film to boot!
What's happening with the tiles being proud of the trim. Rough as toast
Thanks for this. I had not been sure if it was OK to put the adhesive on the tiles as I was taught many years ago to put adhesive on an area of wall. The problem with that is you might do too big an area and have to remove excess at the end.
I use my eye to level the tiles , saves on spirit levels, battens, spacers and screws. Easy money in my pocket. FYI I'm not very busy with work if anyone needs a hand.
instablaster.
I have a motorway bridge that needs reinforcing. Interested?
The corner miter is an uneven join. Won't that get moisture inside?
Funniest video I’ve seen for ages
Beautiful work
That guys works in my local b&q and stands at the door and says hello all the time done well for himself
He barely back buttered that tile tho. This going in a shower? Ouch
OMG what a cowboy 🤠😂🤣🤣
Oh god.. there was no adhesive at all around the edges where that tile strip went in.
And he got a cuppa tea at the end.wow
TSCL_LuFc-Jackツ 😂🤣🤣🤣😂😂😂🤣🤣🤣
Why does he have to start tiling by the window? Waiting for the adhesive to set before he can remove the support will just delay the job.
Hes Having a right mare with that trowel
Yes, the corner must be decorated with ceramic tiles, for the sake of beauty and safety.
Thank you..now i look really good :)
U don't need any support wood for holding tiles if you use good adhesive not ready mixed shit
Stevie wonder would be happy to see that
WELL DONE, CHEERS
Wow! That’s rough!
That rare occasion when you say who the bloody hell gave this 29 up votes! Start at the top...then only tile half way up...oh, the list is endless...worst vid ever!!!!
Thanks
The left lower corner tile is uneven.
this is actually poor tiling, no levelling tools, edges are scrappy, the way he applies adhesive was dreadful! the whole back of the tile should have a full layer
Should be titled How NOT to tile around window.
Why not have 3 full tiles rather than have to cut all the bottom row. So what if the tiles would be a couple inches higher up the wall. Weird.
Also no explanation of the window sil trim. You seem to have left the sil tiles short of the trim? This would then need to be filled with grout. Not a nice look. Trim is so you don't have grout along those corners/bends.
Suggested title change - "Why Not to Tile Windows by Yourself"
This man isn’t a tiler ...
wow! there are alot of amateur things going on here, quite embarrassing tbh. first off, it looks like you layout from left to right is centered incorrectly, yes the window is centered, but if you had moved the complete right to left layout over one half tile, you would of had big centered cuts everywhere instead of those smaller cuts. also tiling the sill should be done before the sides, not after. you never shimmed the schluters to be completed even with the tiles edge. you should always apply adhesive to walls also, not just tile. you also didn't use enough adhesive when you were tiling the bottom section, you can clearly see the wall boards in between the trowel notches. and what's with starting on that board? that's just a waste of time because you now have to shimm from that board and then shimm again at base, if you just start at bottom, your just shimming once and you don't have to spend the time screwing and leveling that board. just make a level line up from base 1 or 2 tiles and shim to it, then keep going up. lots of mistakes imo
incorrect. Around windows tikes needs to be angled, otherwise water will stand. No need to use any profiles for hiding, cut tiles in an angle... like 45 degree
What a joke! Tiles not fully buttered.Tiles cut inacurrately. Trim inserted AFTER tiles laid(!)- remind me not to follow B and Q advice on anything.
It's easier to remove adhesive before it hardens. Huh, who knew....?
i tried to tile my bathroom floor and walls once... made a right pigs ear of it.
Nicely mansplained at the end, and good girl bringing up the tea!
😒
How it should be!
She forgot his sandwich! 😂
How about using bullnose tile on the edges instead of amateur looking metal edging?
Hahahahaha! Omg the comments here! Lmfao! Mr. Magoo doing tile hahahahaha.
I wouldn’t get paid for that job.
Guy's guy's come on it is BQ after all !!! Did you expect anything more than shite....?
Bloody awful around that window
My dad could do a better job than this, and he’s never done any tiling ! And he’s been dead for 23 years!!!
I'm off for a little cry.
😆😆😆😆😆 It's satire, right?
Omg and he’s got a B&q shirt..he’s got to be fired by now
I only tiled twice and mine looks so much better than his crappy job
The wrong thing is happening
Flipping rookies
wow thats a bad job
That jobs shite.
and this is a tutorial LMAO im no tiler but that is poor tiling
Tile sill last...fail!
Ty Seng i
Absolutely terrible , no one should use this as a guide
That’s poor wow 😮
Looks horrible
wow! there are alot of amateur things going on here, quite embarrassing tbh. first off, it looks like your layout from left to right is centered incorrectly, yes the window is centered, but if you had moved the complete right to left layout over one half tile, you would of had big centered cuts everywhere instead of those smaller cuts. also tiling the sill should be done before the sides, not after. you never shimmed the schluters to be completely even with the tiles edge. you should always apply adhesive to walls also, not just tile. you also didn't use enough adhesive when you were tiling the bottom section, you can clearly see the wall boards in between the trowel notches. and what's with starting on that board? that's just a waste of time because you now have to shimm from that board and then shimm again at base, if you just start at bottom, your just shimming once and you don't have to spend the time screwing and leveling that board. just make a level line up from base 1 or 2 tiles and shim to it, then keep going up. lots of mistakes imo
vapdivrr you posted the same comment twice?are you a tile setter by trade? If so maybe you should post some videos so others can critique your work. I'm not saying this guy did a good job and your right about everything you said.im just saying.