I will be your saviour my friend. Its the connector or the input of the battery some pins inside are pushed bacjwards over time or you messed up. Its the part when you insert the battery into the drone you plug the cable right next to the start button. That is the problem that plug or input. 😊❤❤❤❤❤❤❤❤❤
@vietmove hello I need your help I watched your video I assembled around 15 axis kits but I want to put rcinpowers like you impossible I have 9 errors in the mask like you what should I do? thanks to you
Did you get a gimbal calibration error after plugging back in cables and putting avata all back together? I did after replacing motor and im stuck there still. It all worked before taking it apart to replace motor😢
hi, thanks for the amazing guide, I have followed all the steps but front 2 motors are not moving. on goggles it show propulsion and esc error. would you please help.
good day fellow pilot, I still have the same problem battery installation error, what can I do about it i.e. watched videos and tried who can help me solve it, even a new battery, same message...!!!!!!
@@vietmove I fixed it by drying it for 2 days and also leaving it powered on in closed bag, so it heated up. It was a mistake to wash the drone with water. I fixed motors by leaving motors with esc beeper enabled. It was probably due to water/dust damage. Thanks for your reply anyway.
#vietmove 🤩🤩hello I need your help I watched your video I assembled around 15 axis kits but I want to put rcinpowers like you impossible I have 9 errors in the mask like you what should I do? thanks to you
I got the same problem, change the bad motor and fixed my problem too. Very nice video explain this problem. Easy to fix
Glad it helped
_how to fix battery communication bro.. its been a month i can't fly my 3.5 avata because of this problem.. please help me bro. Thanks
I will be your saviour my friend. Its the connector or the input of the battery some pins inside are pushed bacjwards over time or you messed up. Its the part when you insert the battery into the drone you plug the cable right next to the start button. That is the problem that plug or input. 😊❤❤❤❤❤❤❤❤❤
May i know if i change motors esc error will fix?
2 error appear in my goggles Propulsion syemtem error and esc error
Absolutely
Thanks for showing this. Awesome video
No problem 👍
@vietmove hello I need your help I watched your video I assembled around 15 axis kits but I want to put rcinpowers like you impossible I have 9 errors in the mask like you what should I do? thanks to you
Nice video!
Did you get a gimbal calibration error after plugging back in cables and putting avata all back together? I did after replacing motor and im stuck there still. It all worked before taking it apart to replace motor😢
No i havent got that, after plug in n out many time, even i replace another cracking gps cable, everything still fine
@VIETMOVE
Can you notice on your avata if you look under the camera or when you took apart was the camera cable covered or showing exposed wire
2cm from camera gimble is covered with fabric/rubber, then is foil sheild to flight controller
Hi ! thank you for your video. I also find the module where the ESC is very hot without having taken off, is this normal?
Try to check or replace the motor at that esc position
hi, thanks for the amazing guide, I have followed all the steps but front 2 motors are not moving. on goggles it show propulsion and esc error.
would you please help.
Try to replace one by one motor you will find the wrong one
I got a problem , I can't connect my avata with goggles how can I fix it?
Replace the rx board
Thank you! Replace motor, solve ESC error?
Almost, test with any another (in good condition) motor
good day fellow pilot, I still have the same problem battery installation error, what can I do about it
i.e. watched videos and tried who can help me solve it, even a new battery, same message...!!!!!!
Maybe one or few wires from the connector to the flightcontroller have broken, need to teardown the drone then check the wire continious.
Brother my DJI avata one side motor working one side not working please help me
Just replace it
@@vietmove thanks brother
How to fix sensor error on avata 2? And what sensor is that!?
Downward sensor
@@vietmove I fixed it by drying it for 2 days and also leaving it powered on in closed bag, so it heated up. It was a mistake to wash the drone with water. I fixed motors by leaving motors with esc beeper enabled. It was probably due to water/dust damage. Thanks for your reply anyway.
#vietmove 🤩🤩hello I need your help I watched your video I assembled around 15 axis kits but I want to put rcinpowers like you impossible I have 9 errors in the mask like you what should I do? thanks to you
What motor model did you use?
bullshit, i had to send mine off for a new board
If you dont have any electrical experience, its the best way