I did this many years ago and now it needs it again. I did use ford part. It will a little harder because I don't bend like I use to. Thanks for this post.
Great video! It was a lot of help! We found a way to cheat rather than having to cut it with a hack saw! We also didn’t have to drill any holes with a drill bit! The bottom of the dash comes loose! Was about six screws and it gives wiggle room! We did both actuators while we were in there. The driver side is a lot easier, I’ll tell you what! 😂
@@ryanhablitzel the clicking noise drove me crazy, car had no heat, after watch your video i replaced the part with easy .it fixed the issue , cant say how happy it make the kids to have heat again...thank you
Hi Ryan. I have this exact issue in my 2004 Explorer and am trying to decide whether this fix is truly worth it to me. How long would you say this fix took you from first removal of the center console to reattachment of the center console, excluding your time spent buying the new actuator and your various junkyard pieces?
It was a challenging install. Especially since there weren’t any good videos detailing how to fix it and I had to figure things out on my own. If you follow the steps in my video, I think you could do this install in 4-5 hours depending on your mechanical ability.
There are several issues that could cause a no heat situation, but the blend door is common on these. It doesn’t always make the clunking sound when they go bad.
Hi Ryan great video I did this repair once by removing the dash and don't want to go that route again. My question is, after you drilled the hole in the side of the glove box you then said it was a lesson learned and you went after the wrong gold colored screw but you didn't mention if there is no need to drill that hole?
I definitely needed to drill the hole to get access to the correct screws. The hole drilled in the dash support did not hinder the strength of the dash support significantly in my opinion.
Right on it was the little gear all along just didn't notice it at first. I ordered the motorcraft replacement part, hopefully get it by the end of the week.
how did you get the bottom right bolt out of the on the actuator below where you drilled the hole? OK I SEE WHEN YOU PUT BACK IN THATS WAS WERE YOU DRILLED THE SECOND HOLE AT 14:30 Thanks! Mines never mad a popping sound or clicking just no heat on passenger side!
Does the single climate control also have that second actuator? I have an 05 explorer with the single climate control that was stuck on heat. I ended up removing the driver blend door actuator and the ac started blowing cold on both sides. The actuator has no movement when adjusting the temperature so i know its bad. The only thing is on the passenger side where the other actuator is supposed to be its not there but theres a broken piece of plastic sticking out where the rod is suppose to go in as if there was once an actuator there.
These explorers came with many configurations for the heating and air conditioning set up. It’s hard to know for each design. If you see a plastic peace broken, it would probably indicate something is missing. There are probably plenty of these explorers at local pick and pull. You could go and check out similar models at the junk yard to see what the set-up looks like on your model.
I did this many years ago and now it needs it again. I did use ford part. It will a little harder because I don't bend like I use to. Thanks for this post.
It’s a tough job for sure, but definitely doable!
Excellent video. Thankful you mentioned there are many different ways Ford has these. This one was the one I am dealing with. Thank You!!!!!!
Glad it was helpful!
Great video! Thank you. I can’t wait to do this myself.
Glad it was helpful!
Great video! It was a lot of help! We found a way to cheat rather than having to cut it with a hack saw! We also didn’t have to drill any holes with a drill bit! The bottom of the dash comes loose! Was about six screws and it gives wiggle room! We did both actuators while we were in there. The driver side is a lot easier, I’ll tell you what! 😂
Nice! That’s great info!
Wow I’m going tomorrow it got dark on me good going man !!
Part through the dealer was a bit pricey as I recall, but I would only want to do this repair with quality OEM parts.
great video,you help me diagnose my issue , thanks
Glad it helped!
@@ryanhablitzel the clicking noise drove me crazy, car had no heat, after watch your video i replaced the part with easy .it fixed the issue , cant say how happy it make the kids to have heat again...thank you
I did that in my 05 Ford Explorer v-8
Nice looking ford
Thanks! It’s a big job!
It was very helpful, thanks
You’re welcome!
Thanks for the tip.
You’re welcome
Hi Ryan. I have this exact issue in my 2004 Explorer and am trying to decide whether this fix is truly worth it to me.
How long would you say this fix took you from first removal of the center console to reattachment of the center console, excluding your time spent buying the new actuator and your various junkyard pieces?
It was a challenging install. Especially since there weren’t any good videos detailing how to fix it and I had to figure things out on my own. If you follow the steps in my video, I think you could do this install in 4-5 hours depending on your mechanical ability.
I have that very same issue no heating. I don’t have that clonking sound
There are several issues that could cause a no heat situation, but the blend door is common on these. It doesn’t always make the clunking sound when they go bad.
Hi Ryan great video I did this repair once by removing the dash and don't want to go that route again. My question is, after you drilled the hole in the side of the glove box you then said it was a lesson learned and you went after the wrong gold colored screw but you didn't mention if there is no need to drill that hole?
I definitely needed to drill the hole to get access to the correct screws. The hole drilled in the dash support did not hinder the strength of the dash support significantly in my opinion.
What if you get the driver's side one off, test the motor and it appears to be working right? Its like the door is stuck closed. Any advice?
There also some vacuum operated actuators under there that could fail. Not sure if that’s the issue.
Right on it was the little gear all along just didn't notice it at first. I ordered the motorcraft replacement part, hopefully get it by the end of the week.
Nice! Glad you worked it out!
how did you get the bottom right bolt out of the on the actuator below where you drilled the hole? OK I SEE WHEN YOU PUT BACK IN THATS WAS WERE YOU DRILLED THE SECOND HOLE AT 14:30 Thanks! Mines never mad a popping sound or clicking just no heat on passenger side!
Yeah, it’s a puzzle 👌🏼
The dual climate control has only 1 blend door actuator? Or is there another one on the driver side?
There is another one on the drivers side.
Also pulled the seats out haha!
How much was that part ??
Does the single climate control also have that second actuator? I have an 05 explorer with the single climate control that was stuck on heat. I ended up removing the driver blend door actuator and the ac started blowing cold on both sides. The actuator has no movement when adjusting the temperature so i know its bad. The only thing is on the passenger side where the other actuator is supposed to be its not there but theres a broken piece of plastic sticking out where the rod is suppose to go in as if there was once an actuator there.
These explorers came with many configurations for the heating and air conditioning set up. It’s hard to know for each design. If you see a plastic peace broken, it would probably indicate something is missing. There are probably plenty of these explorers at local pick and pull. You could go and check out similar models at the junk yard to see what the set-up looks like on your model.
FORD JUNK!
Haha 😆
As junk as GM blower motors
The dual climate control has only 1 blend door actuator? Or is there another one on the driver side?
It has two